Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P260096  Motor/Generator Coolant Pump "A" Control Circuit Component Internal Failure  


DESCRIPTION

Refer to the description for DTC P260031.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P260031

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P260096 Motor/Generator Coolant Pump "A" Control Circuit Component Internal Failure When the oil pump startup request signal is output, the temperature of the drive motor exceeds the threshold due to excessive starting failure.
(2 trip detection logic)
·

Oil pipe

·

OIL PMP fuse

·

OIL PMP MTR relay

·

Oil pump with motor assembly

·

EV control ECU

·

Wire harness or connector


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P260096
·

Target Motor/Generator Cooling Oil Pump Motor Duty

·

Motor/Generator Cooling Oil Pump Motor Revolution

·

Motor/Generator Cooling Oil Pump Motor Power Relay Request



HINT:

The oil pump with motor assembly cannot be activated only with the OIL PMP relay on. It is activated after receiving the command signals (OPM1) from the EV control ECU.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Enter the following menus: Powertrain / EV / Active Test / Control the Motor/Generator Cooling Oil Pump.

4.

According to the display on the GTS, perform the Active Test and set the duty to 90%.

HINT:

The Active Test cannot be performed if the duty ratio is set to 50% or lower or 95% or higher, or if the ambient temperature is -11°C (12.2°F) or lower.


5.

According to the display on the GTS, read the Data List and check that the value of "Motor/Generator Cooling Oil Pump Motor Revolution" is between 450 rpm and 7000 rpm.

6.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

7.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P260031.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P260031

PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P260096 is output A
P260096 and any DTCs in the table below are output B


Relevant DTC
P274A11 Transmission Fluid Temperature Sensor "C" Circuit Short to Ground
P274A15 Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open
P274A1C Transmission Fluid Temperature Sensor "C" Voltage Out of Range
P274A1F Transmission Fluid Temperature Sensor "C" Circuit Intermittent

HINT:

The transmission fluid temperature sensor value is used to detect DTC P260096. Check that the transmission fluid temperature sensor operates normally, as the detection condition for DTC P260096 may be mistakenly detected due to a malfunction in the transmission fluid temperature sensor.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK OIL PIPE

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK OIL PIPE
a.

Check that there is no clogging in the oil pipes connected to the oil pump with motor assembly, oil cooler assembly and hybrid vehicle transaxle assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (OIL PUMP WITH MOTOR ASSEMBLY CONNECTOR)

NG

REPAIR OR REPLACE OIL PIPE

3.CHECK CONNECTOR CONNECTION CONDITION (OIL PUMP WITH MOTOR ASSEMBLY CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

5.CHECK FUSE (OIL PMP)

NG

CONNECT SECURELY

5.CHECK FUSE (OIL PMP)

OK

6.INSPECT OIL PMP MTR RELAY

NG

REPLACE FUSE (OIL PMP)

6.INSPECT OIL PMP MTR RELAY

OK

7.CHECK HARNESS AND CONNECTOR (LUGGAGE ROOM RELAY BLOCK)

NG

REPLACE RELAY (OIL PMP MTR)

7.CHECK HARNESS AND CONNECTOR (LUGGAGE ROOM RELAY BLOCK)

OK

8.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)

OK

9.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - OIL PMP MTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - OIL PMP MTR RELAY)

OK

10.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PMP MTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PMP MTR RELAY)

OK

11.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (OIL PUMP WITH MOTOR ASSEMBLY - BODY GROUND)

OK

12.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

OK

13.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - OIL PUMP WITH MOTOR ASSEMBLY)

OK

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE MOTOR/GENERATOR COOLING OIL PUMP MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE MOTOR/GENERATOR COOLING OIL PUMP MOTOR)

Pre-procedure1

a.

Set the Duty ratio to 90%.

HINT:

The active test is not performed when the Duty ratio is 50% or lower or 95% or higher, or the ambient temperature is -11°C (12.2°F) or lower.


Powertrain > EV > Active Test
Tester Display
Control the Motor/Generator Cooling Oil Pump
50004 397 42002

Procedure1

a.

Confirm that the oil pump with motor assembly is operating.

OK:

The oil pump with motor assembly is operating.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

15.INSPECT OIL PUMP WITH MOTOR ASSEMBLY

NG

16.INSPECT EV CONTROL ECU
15.INSPECT OIL PUMP WITH MOTOR ASSEMBLY

Pre-procedure1

a.

Remove the oil pump with motor assembly.

HINT:

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>OIL PUMP (for Mechanical Type)>REMOVAL



Procedure1

a.
A217273C19
0.75,1.667 1.125,1.052 true 1.833,1.667 1.615,1.052 true 0.156,0.177 0.5,0.396 0.344,0.219 11 false *a 0.719,1.74 1.063,1.958 0.344,0.219 11 false L 1.688,1.729 2.292,1.948 0.604,0.219 11 false OPM1
*a Component without harness connected
(Oil Pump with Motor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (OPM1) - 4 (L) Ignition switch off 10 kΩ or higher
3 (OPM1) - Body ground Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the oil pump with motor assembly.



OK

NG

16.INSPECT EV CONTROL ECU

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Set the Duty ratio to 90%.

HINT:

The active test is not performed when the Duty ratio is 50% or lower or 95% or higher, or the ambient temperature is -11°C (12.2°F) or lower.


Powertrain > EV > Active Test
Tester Display
Control the Motor/Generator Cooling Oil Pump
50004 397 42002

Procedure1

a.
A478491C52
2.031,0.833 2.458,1.188 0.427,0.354 0.188,0.375 0.646,0.729 0.458,0.354 0.198,0.813 0.656,1.167 0.458,0.354 2.219,1.677 1.948,2.479 true 0.302,1.76 0.24,2.427 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.333,0.917 0.781,1.083 0.448,0.167 10 false A14 2.135,0.948 2.438,1.115 0.302,0.167 10 false A17 1.833,2.51 2.135,2.677 0.302,0.167 10 false E1 0.177,2.49 0.635,2.719 0.458,0.229 10 false OPM1 0.302,0.479 0.75,0.646 0.448,0.167 10 false G14 0.729,0.927 1.177,1.094 0.448,0.167 10 false *B 0.719,0.51 1.167,0.677 0.448,0.167 10 false *A
*A for LHD
*B for RHD
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,A17)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G14-15 (OPM1) - A17-4 (E1) During Active Test 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,A17)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A14-15 (OPM1) - A17-4 (E1) During Active Test 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG