Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P274A11  Transmission Fluid Temperature Sensor "C" Circuit Short to Ground  P274A15  Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the transaxle fluid temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

EV control ECU internal malfunction
·

EV control ECU malfunction


Transaxle fluid temperature sensor malfunction
·

Internal transaxle fluid temperature sensor malfunction

·

Open or short in transaxle fluid temperature sensor


Wire harness between the transaxle fluid temperature sensor and EV control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness



DESCRIPTION

A380229E03
0.104,0.406 1.208,0.76 1.104,0.354 10 false Resistance (kΩ) 1.75,3.052 3.385,3.375 1.635,0.323 10 false Temperature (°C (°F)) 0.729,2.26 0.885,2.458 0.156,0.198 10 false 0 0.865,2.396 1.021,2.594 0.156,0.198 10 false 0 1.563,2.396 1.865,2.625 0.302,0.229 10 false 50 1.188,2.396 1.49,2.625 0.302,0.229 10 false 25 1.938,2.396 2.24,2.625 0.302,0.229 10 false 75 2.271,2.396 2.573,2.625 0.302,0.229 10 false 100 2.635,2.396 2.938,2.625 0.302,0.229 10 false 125 3.01,2.396 3.313,2.625 0.302,0.229 10 false 150 0.719,2.031 1.021,2.26 0.302,0.229 10 false 5 0.688,1.781 0.99,2.01 0.302,0.229 10 false 10 0.677,1.563 0.979,1.792 0.302,0.229 10 false 15 0.688,1.333 0.99,1.563 0.302,0.229 10 false 20 0.688,1.115 0.99,1.344 0.302,0.229 10 false 25 0.688,0.885 0.99,1.115 0.302,0.229 10 false 30 1.167,2.635 1.479,2.906 0.313,0.271 10 false (77) 0.813,2.625 1.125,2.896 0.313,0.271 10 false (32) 1.5,2.646 1.875,2.927 0.375,0.281 10 false (122) 1.885,2.656 2.292,2.927 0.406,0.271 10 false (167) 2.26,2.656 2.667,2.927 0.406,0.271 10 false (212) 2.635,2.656 3.031,2.938 0.396,0.281 10 false (257) 3.021,2.656 3.417,2.99 0.396,0.333 10 false (302)

The resistance of the thermistor built into the transaxle fluid temperature sensor changes in accordance with changes in the transmission fluid temperature. The lower the transaxle fluid temperature, the higher the thermistor resistance. Conversely, the higher the transaxle fluid temperature, the lower the resistance.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P274A11 Transmission Fluid Temperature Sensor "C" Circuit Short to Ground Short to ground in the transmission fluid temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

FCV with motor transaxle assembly (Transaxle fluid temperature sensor)


Master Warning:
Comes on
EV A
P274A15 Transmission Fluid Temperature Sensor "C" Circuit Short to Auxiliary Battery or Open Open or short to +B in the transmission fluid temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

FCV with motor transaxle assembly (Transaxle fluid temperature sensor)


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P274A11 Transaxle Oil Temperature
P274A15

HINT:

After confirming that DTC P274A11 or P274A15 is output, use the GTS to check "Transaxle Oil Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

With ignition switch ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A466134E02
5.604,2.813 6.729,3.073 1.125,0.26 10 false EV Control ECU 6.51,0.792 6.969,0.99 0.458,0.198 10 false ADC 5.396,0.688 5.854,0.885 0.458,0.198 10 false TTA 5.375,1.865 5.927,2.073 0.552,0.208 10 false ETTA 1.333,0.667 1.792,0.865 0.458,0.198 10 false TTA 1.219,1.875 1.771,2.083 0.552,0.208 10 false ETTA 0.188,2.854 2.073,3.438 1.885,0.583 10 false FCV with Motor Transaxle Assembly (Transaxle Flud Temperature Sensor) 2.365,0.656 2.823,0.854 0.458,0.198 10 false 15 2.313,2.688 3.333,3.115 1.021,0.427 10 false NO. 3 Floor Wire Connector 5.094,0.677 5.552,0.875 0.458,0.198 10 false 20 5.104,1.865 5.563,2.063 0.458,0.198 10 false 28 5.615,2.646 6.073,2.844 0.458,0.198 10 false A15 0.198,2.688 0.656,2.885 0.458,0.198 10 false G154 2.615,2.51 2.927,2.708 0.313,0.198 10 false GG2 3.031,1.865 3.49,2.063 0.458,0.198 10 false 16 3.75,1.854 4.052,2.042 0.302,0.188 10 false 18 4.438,0.677 4.896,0.875 0.458,0.198 10 false 17 3.042,0.656 3.5,0.854 0.458,0.198 10 false 15 1.76,0.667 2.219,0.865 0.458,0.198 10 false 12 1.75,1.854 2.208,2.052 0.458,0.198 10 false 4 2.354,1.865 2.813,2.063 0.458,0.198 10 false 16 3.781,0.667 4.24,0.865 0.458,0.198 10 false 17 4.458,1.854 4.76,2.042 0.302,0.188 10 false 18 4.021,2.521 4.333,2.719 0.313,0.198 10 false AG2 3.677,2.708 4.813,3.063 1.135,0.354 10 false NO. 2 Floor Wire Connector

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2A11

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK CONNECTOR CONNECTION CONDITION (TRANSAXLE FLUID TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CONNECTOR CONNECTION CONDITION (TRANSAXLE FLUID TEMPERATURE SENSOR CONNECTOR)
a.
A479479

Check the connection condition of the transaxle fluid temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

5.READ VALUE USING GTS (TRANSAXLE OIL TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (TRANSAXLE OIL TEMPERATURE)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Transaxle Oil Temperature
50003 397 322
Result:
Result Proceed to
The value of Transaxle Oil Temperature is -40 °C A
The value of Transaxle Oil Temperature is 215 °C B
None of the above conditions are met C


HINT:

-40°C = -40°F

215°C = 419°F



Post-procedure1

a.

Turn the ignition switch off.



A

6.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (TRANSAXLE FLUID TEMPERATURE SENSOR)

B

8.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (TRANSAXLE FLUID TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (TRANSAXLE FLUID TEMPERATURE SENSOR)

Pre-procedure1

a.
A479479

Disconnect the G154 transaxle fluid temperature sensor connector.


Procedure1

a.
A479452C02
1.458,0.208 1.969,0.583 0.51,0.375 1.844,1.427 2.406,1.813 true 1.104,1.823 1.615,1.094 true 0.135,0.167 0.448,0.365 0.313,0.198 10 false *a 0.792,1.844 1.25,2.042 0.458,0.198 10 false ETTA 2.302,1.844 2.76,2.042 0.458,0.198 10 false TTA 1.563,0.323 1.958,0.521 0.396,0.198 10 false G154
*a Component without harness connected
(Transaxle Fluid Temperature Sensor (FCV with Motor Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G154)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

G154-12 (TTA) - G154-4 (ETTA) Ignition switch off 1.4 to 94 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G154 transaxle fluid temperature sensor connector.



OK

7.INSPECT EV CONTROL ECU

NG

7.INSPECT EV CONTROL ECU

Pre-procedure1

a.
A478491C20
0.802,0.802 1.271,1.156 0.469,0.354 1.281,1.906 1.063,2.49 true 1.292,1.823 1.833,2.552 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.927,0.906 1.229,1.073 0.302,0.167 10 false A15 0.885,2.552 1.51,2.75 0.625,0.198 10 false ETTA 1.865,2.552 2.25,2.719 0.385,0.167 10 false TTA
*a Component with harness connected
(EV Control ECU)


Connect terminals 20 (TTA) and 28 (ETTA) of the A15 EV control ECU connector.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Transaxle Oil Temperature
50003 397 322
OK:
Tester Display Condition Specified Condition
Transaxle Oil Temperature Terminals A15-20 (TTA) and A15-28 (ETTA) connected
Ignition switch ON
215°C (419°F)


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSAXLE FLUID TEMPERATURE SENSOR - EV CONTROL ECU)

NG

8.INSPECT FCV WITH MOTOR TRANSAXLE ASSEMBLY (TRANSAXLE FLUID TEMPERATURE SENSOR)

Pre-procedure1

a.
A479479

Disconnect the G154 transaxle fluid temperature sensor connector.


Procedure1

a.
A479452C02
1.458,0.208 1.969,0.583 0.51,0.375 1.844,1.427 2.406,1.813 true 1.104,1.823 1.615,1.094 true 0.135,0.167 0.448,0.365 0.313,0.198 10 false *a 0.792,1.844 1.25,2.042 0.458,0.198 10 false ETTA 2.302,1.844 2.76,2.042 0.458,0.198 10 false TTA 1.563,0.323 1.958,0.521 0.396,0.198 10 false G154
*a Component without harness connected
(Transaxle Fluid Temperature Sensor (FCV with Motor Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G154)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

G154-12 (TTA) - G154-4 (ETTA) Ignition switch off 1.4 to 94 kΩ


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G154 transaxle fluid temperature sensor connector.



OK

9.CHECK HARNESS AND CONNECTOR (TRANSAXLE FLUID TEMPERATURE SENSOR - EV CONTROL ECU)

NG

9.CHECK HARNESS AND CONNECTOR (TRANSAXLE FLUID TEMPERATURE SENSOR - EV CONTROL ECU)

Pre-procedure1

a.

Disconnect the G154 transaxle fluid temperature sensor connector.


b.

Disconnect the A15 EV control ECU connector.


Procedure1

a.
A481449C01
0.906,1.917 1.427,2.302 0.521,0.385 1.479,0.104 1.958,0.5 0.479,0.396 1.813,0.958 2.354,0.438 true 1.698,1.219 1.969,1.74 true 1.333,3.854 1.219,4.302 true 1.333,3.781 1.813,3.708 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.167,2.01 0.479,2.208 0.313,0.198 10 false *b 1.563,0.24 1.99,0.438 0.427,0.198 10 false G154 1.063,2.042 1.375,2.24 0.313,0.198 10 false A15 1.875,1.792 2.271,2.063 0.396,0.271 10 false TTA 2.406,0.323 2.938,0.635 0.531,0.313 10 false ETTA 1.094,4.344 1.625,4.656 0.531,0.313 10 false ETTA 1.854,3.656 2.25,3.927 0.396,0.271 10 false TTA
*a Front view of wire harness connector
(to Transaxle Fluid Temperature Sensor)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(G154,A15)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G154-12 (TTA) - A15-20 (TTA) Ignition switch off Below 1 Ω
G154-4 (ETTA) - A15-28 (ETTA) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(G154,A15)Location & Routing

Click Connector(G154)Body>Floor Wire / No. 3 Floor Wire>FCV Transaxle with Motor Assembly

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G154-12 (TTA) or A15-20 (TTA) - Body ground and other terminals Ignition switch off 10 kΩ or higher
G154-4 (ETTA) or A15-28 (ETTA) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A15 EV control ECU connector.


b.

Reconnect the G154 transaxle fluid temperature sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR