Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P312487  Communication Error from Hybrid/EV Powertrain Control Module to Drive Motor Control Module "A" Missing Message  


DESCRIPTION

The MG ECU, which is built into in the inverter with converter assembly, controls drive motor based on commands from the EV control ECU.

The MG ECU monitors communication data and detects malfunctions.

A communication error between the MG ECU and EV control ECU is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P312487 Communication Error from Hybrid/EV Powertrain Control Module to Drive Motor Control Module "A" Missing Message Error in signal EV control ECU to the inverter with converter assembly (MG ECU) via serial communication (no transmission, out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

EV control ECU


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 2 minutes or more.

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the inverter low-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

If DTC P312487 was stored due to incomplete engagement of the connectors, and the system returns to normal when the ignition switch is turned to ON after clearing the DTCs, DTC P0A1B1F will be stored. Proceed to troubleshooting without considering DTC P0A1B1F.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK DTC OUTPUT (EV)
2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Turn the ignition switch to ON and wait for 2 minutes or more.


b.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P312487 is output A
P312487 is not output B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK EV CONTROL ECU (HTM CHECK WAVEFORM)

B

3.CHECK EV CONTROL ECU (HTM CHECK WAVEFORM)
a.

Turn the ignition switch to ON (IG).


b.

Connect an oscilloscope between the EV control ECU terminals specified in the table below.


c.
A481543C03
1.469,0.365 1.885,0.677 0.417,0.313 2.073,0.365 2.49,0.677 0.417,0.313 1.406,1.813 1.76,1.125 true 2.083,1.823 1.813,1.125 true 2.656,1.813 2.271,1.063 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.573,0.448 1.885,0.604 0.313,0.156 10 false A16 2.167,0.458 2.552,0.615 0.385,0.156 10 false A17 2.073,1.854 2.521,2.094 0.448,0.24 10 false HTM+ 1.115,1.844 1.563,2.083 0.448,0.24 10 false HTM- 2.677,1.833 3.125,2.073 0.448,0.24 10 false E1 0.323,2.792 0.771,3.031 0.448,0.24 10 false CH1 0.302,3.49 0.75,3.729 0.448,0.24 10 false CH2 2.927,3.208 3.375,3.448 0.448,0.24 10 false GND 2.917,3.813 3.365,4.052 0.448,0.24 10 false GND
*a Component with harness connected
(EV Control ECU)


Measure the waveform.

Tester Connection Condition Equipment Setting

Click Location & Routing(A16,A17)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

CH1: A16-10 (HTM+) - A17-4 (E1)
CH2: A16-11 (HTM-) - A17-4 (E1)
Ignition switch ON 1 V/DIV, 200 μs/DIV

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




Result:
Result Proceed to
There is an interruption or distortion in the waveform A
There are no interruptions or distortions in the waveform B


d.

Turn the ignition switch off.



A

4.CHECK EV CONTROL ECU (CLK CHECK WAVEFORM)

B

10.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)
4.CHECK EV CONTROL ECU (CLK CHECK WAVEFORM)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P312387

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



A

5.CHECK EV CONTROL ECU (REQ CHECK WAVEFORM)

B

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
5.CHECK EV CONTROL ECU (REQ CHECK WAVEFORM)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P312387

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

OK

7.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERNAL RESISTANCE (REQ))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERNAL RESISTANCE (REQ))

OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

OK

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERNAL RESISTANCE (CLK))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERNAL RESISTANCE (CLK))

OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Disconnect the A16 EV control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON (IG).


f.

Measure the voltage according to the value(s) in the table below.

A480891C18
1.948,0.427 2.365,0.76 0.417,0.333 5.208,0.156 5.625,0.49 0.417,0.333 1.219,0.427 1.635,0.76 0.417,0.333 1.76,2.188 1.49,1.417 true 1.01,2.167 1.406,1.417 true 5.104,2.281 5.448,1.656 true 5.885,2.292 5.5,1.656 true 0.552,0.208 0.865,0.365 0.313,0.156 10 false *a 3.531,0.188 3.844,0.344 0.313,0.156 10 false *b 1.313,0.531 1.583,0.729 0.271,0.198 10 false A19 5.313,0.26 5.583,0.458 0.271,0.198 10 false A16 1.719,2.219 2.146,2.427 0.427,0.208 10 false HTM+ 0.823,2.229 1.25,2.438 0.427,0.208 10 false HTM- 4.813,2.302 5.24,2.51 0.427,0.208 10 false HTM- 5.885,2.302 6.313,2.51 0.427,0.208 10 false HTM+ 1.688,0.521 1.958,0.719 0.271,0.198 10 false *A 2.031,0.521 2.302,0.719 0.271,0.198 10 false A18 2.417,0.552 2.688,0.75 0.271,0.198 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-10 (HTM+) - Body ground Ignition switch ON Below 1 V
A16-11 (HTM-) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON (IG) with the EV control ECU connector and the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A19)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-10 (HTM+) - A19-23 (HTM+) Ignition switch off Below 1 Ω
A16-11 (HTM-) - A19-22 (HTM-) Ignition switch off Below 1 Ω
A16-10 (HTM+) or A19-23 (HTM+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-11 (HTM-) or A19-22 (HTM-) - Body ground and other terminals Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A16,A18)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A16-10 (HTM+) - A18-23 (HTM+) Ignition switch off Below 1 Ω
A16-11 (HTM-) - A18-22 (HTM-) Ignition switch off Below 1 Ω
A16-10 (HTM+) or A18-23 (HTM+) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A16-11 (HTM-) or A18-22 (HTM-) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG


j.

Reconnect the A16 EV Control ECU connector.


k.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

11.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERNAL RESISTANCE (HTM))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERNAL RESISTANCE (HTM))

Pre-procedure1

a.

Disconnect the A16 EV control ECU connector.


Procedure1

a.
A478494C11
1.427,0.646 1.885,1 0.458,0.354 1.708,2.385 1.385,3.01 true 1.781,2.375 2.24,2.979 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.552,0.75 1.854,0.917 0.302,0.167 10 false A16 1.125,3.042 1.51,3.229 0.385,0.188 10 false HTM- 2.01,3.031 2.469,3.229 0.458,0.198 10 false HTM+
*a Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A16)Location & Routing

Click Connector(A16)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A16-10 (HTM+) - A16-11 (HTM-) Ignition switch off 109 to 131 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A16 EV control ECU connector.



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY