Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DAA12  Exhaust Drainage Valve Circuit Short to Battery  P1DAA14  Exhaust Drainage Valve Circuit Short to Ground or Open  


DESCRIPTION

The FC system normally seals the FC stack assembly to keep hydrogen so as to deliver sufficient power generation performance of the FC stack. The exhaust drainage valve is used to remove produced water, which impedes power generation, and nitrogen, which comes from the cathode, from the hydrogen circulation system as needed.

The entire FC system is monitored by the FC control ECU, and the exhaust drainage valve is actuated open when it receives request signals from the FC control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DAA12 Exhaust Drainage Valve Circuit Short to Battery All of the following conditions are met, and there is a short in the +B circuit of the exhaust drainage valve circuit (DTC detection signal is large) for more than 2 seconds.
·

Auxiliary battery voltage is between 10.5 to 15 V

·

Exhaust drainage valve is not being energized


(1 trip detection logic)
·

Exhaust drainage valve (hydrogen recirculation separator assembly)

·

FC control ECU

·

FC-B relay

·

Wire harness or connector


Master Warning: Comes on FC A
P1DAA14 Exhaust Drainage Valve Circuit Short to Ground or Open All of the following conditions are met, and there is an open in the exhaust drainage valve circuit or a short to the GND circuit (DTC detection signal is small) for more than 2 seconds.
·

Auxiliary battery voltage is between 10.5 to 15 V

·

Exhaust drainage valve is not being energized


(1 trip detection logic)
·

Exhaust drainage valve (hydrogen recirculation separator assembly)

·

FC control ECU

·

FC PWR relay

·

Wire harness or connector


Master Warning: Comes on FC A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List
DTC No. Data List
P1DAA12 -
P1DAA14

HINT:

It is suspected that malfunctions, or open/short circuits have occurred in the exhaust drainage valve.


WIRING DIAGRAM

A477002E08
0.531,0.51 1.448,0.708 0.917,0.198 10 false FC-B NO. 1 3.521,0.385 4.438,0.583 0.917,0.198 10 false +BP3 1.625,2.438 2.542,2.635 0.917,0.198 10 false IGCT NO. 2 0.583,3.823 1.177,4.292 0.594,0.469 10 false Auxiliary Battery 1.542,1.688 1.708,1.854 0.167,0.167 10 false 3 1.542,2.042 1.708,2.208 0.167,0.167 10 false 2 2.313,2.052 2.479,2.219 0.167,0.167 10 false 1 2.313,1.677 2.479,1.844 0.167,0.167 10 false 5 1.49,0.625 1.656,0.792 0.167,0.167 10 false 2 2.281,0.646 2.448,0.813 0.167,0.167 10 false 1 2.292,0.26 2.458,0.427 0.167,0.167 10 false 5 1.49,0.26 1.656,0.427 0.167,0.167 10 false 3 3.521,3.667 4.438,3.865 0.917,0.198 10 false E1 3.198,3.646 3.594,4.031 0.396,0.385 10 false B1 3.177,0.375 3.542,0.646 0.365,0.271 10 false A48 5.198,1.24 5.563,1.49 0.365,0.25 10 false B1 5.208,1.771 5.542,2.042 0.333,0.271 10 false B1 4.688,1.125 5.604,1.323 0.917,0.198 10 false VHVP 4.792,1.667 5.708,1.865 0.917,0.198 10 false HVP 5.906,1.125 6.823,1.323 0.917,0.198 10 false VHVP 5.906,1.656 6.823,1.854 0.917,0.198 10 false HVP 5.719,1.115 5.885,1.281 0.167,0.167 10 false 2 5.708,1.656 5.875,1.823 0.167,0.167 10 false 1 5.656,2.563 7.156,3.271 1.5,0.708 10 false Exhaust Drainage Valve (Hydrogen Recirculation Separator Assembly) 5.656,2.385 6.073,2.646 0.417,0.26 10 false B26 5.208,1.573 5.438,1.74 0.229,0.167 10 false 81 5.208,1.042 5.438,1.208 0.229,0.167 10 false 41 3.24,0.198 3.469,0.365 0.229,0.167 10 false 2 3.156,3.458 3.438,3.625 0.281,0.167 10 false 104 1.74,1 2.656,1.198 0.917,0.198 10 false FC-B 3.823,4.031 5.229,4.333 1.406,0.302 10 false FC Control ECU 3.604,2.573 4.344,3.198 0.74,0.625 10 false DTC detection signal 4.094,0.677 4.552,0.875 0.458,0.198 10 false +BP3 4.74,0.677 5.198,0.875 0.458,0.198 10 false +BP3 1.646,3.948 2.76,4.302 1.115,0.354 10 false EV Control ECU 0.417,0.896 1.333,1.094 0.917,0.198 10 false R/B-B NO. 1 0.406,1.448 1.323,1.646 0.917,0.198 10 false R/B FR 0.604,1.948 1.521,2.146 0.917,0.198 10 false IGCT NO. 2 0.573,3 1.281,3.26 0.708,0.26 10 false R/R RR# 2 1.646,3.333 2.24,3.563 0.594,0.229 10 false MREL 1.656,3.792 2.146,3.969 0.49,0.177 10 false A8*1 1.396,3.219 1.594,3.375 0.198,0.156 10 false 21 2.594,1.333 3.375,1.771 0.781,0.438 10 false IGCT NO. 6 2.427,0.521 3.344,0.719 0.917,0.198 10 false FC-B NO. 4 2.052,3.792 2.542,3.969 0.49,0.177 10 false D15*2 5.729,3.854 6.594,4.052 0.865,0.198 10 false *1: for LHD 5.75,4.177 6.615,4.375 0.865,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 2 seconds or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FC CONTROL ECU)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A48,B1)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

A48-2 (+BP3) - B1-104 (E1) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC control ECU connector.



OK

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - EXHAUST DRAINAGE VALVE (HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY))

NG

4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - EXHAUST DRAINAGE VALVE (HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY))

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.
A476973

Disconnect the exhaust drainage valve (hydrogen recirculation separator assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,B26)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(B26)Engine Compartment>No. 2 Stack Wire>Hydrogen Recirculation Separator Assembly

B1-41 (VHVP) - B26-2 (VHVP) Always Below 1 Ω
B1-81 (HVP) - B26-1 (HVP) Always Below 1 Ω
B1-41 (VHVP) or B26-2 (VHVP) - Body ground and other terminals Always 10 kΩ or higher
B1-81 (HVP) or B26-1 (HVP) - Body ground and other terminals Always 10 kΩ or higher



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-41 (VHVP) or B1-81 (HVP) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the exhaust drainage valve (hydrogen recirculation separator assembly) connector.


c.

Reconnect the FC control ECU connector.



OK

3.INSPECT EXHAUST DRAINAGE VALVE (HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT EXHAUST DRAINAGE VALVE (HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY)

OK

NG

REPLACE EXHAUST DRAINAGE VALVE (HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - BODY GROUND)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

B1-104 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC control ECU connector.



OK

5.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC-B RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC-B RELAY)

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Remove the FC-B relay from the No. 1 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A48)Location & Routing

Click Connector(A48)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>FC Control ECU

A48-2 (+BP3) - 5 (FC-B relay holder) Always Below 1 Ω
A48-2 (+BP3) or 5 (FC-B relay holder) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reinstall the FC-B relay.


b.

Reconnect the FC control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR