The hydrogen system of the FC system feeds the FC stack with hydrogen, so that the FC stack can generate power. The low-range pressure circuit is located after the hydrogen injectors, and pressure applied to the circuit is regulated by the hydrogen injectors to an appropriate level for FC stack power generation.
If the regulated low-range hydrogen pressure exceeds a threshold, the EV control ECU interprets it as a higher pressure limit error, and stores this DTC.
For the circuit diagram, refer to DTC P1DC000.
Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1DC000
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P1DC100 | Low-Range Hydrogen Pressure Too High | Low-range hydrogen pressure has exceeded a threshold. This malfunction detection is active all the time.
(1 trip detection logic) |
·
FC stack assembly ·
Hydrogen injector (fuel injector assembly) ·
Hydrogen secondary pressure sensor |
Master Warning: Comes on | EV | B |
If low-range hydrogen pressure increases despite hydrogen injectors being not forced to open, it is suspected that hydrogen injectors are malfunctioning.
| Vehicle Condition | FC shutdown
(ignition switch ON) |
FC startup process | FC intermittent operation | FC is generating power
(vehicle is in stationary) |
FC is generating power
(vehicle is traveling) |
FC shutdown process |
|---|---|---|---|---|---|---|
| Data List
"FC Work Mode" |
Stop | Startup | Working | Finishing | ||
| Data List
"FC Intermittent Operation" |
OFF | ON | OFF | OFF | ||
| DTC Detection | ○ | ○ | ○ | ○ | ○ | ○ |
| DTC No. | Data List |
|---|---|
| P1DC100 | ·
Target Low-Range Hydrogen Pressure ·
Low-Range Hydrogen Pressure (Filtered Value) ·
Tank Shut Valve 1 Drive Status ·
Tank Shut Valve 2 Drive Status ·
Tank Shut Valve 3 Drive Status ·
Hydrogen Injector 1 Injection Period ·
Hydrogen Injector 2 Injection Period ·
Hydrogen Injector 3 Injection Period ·
Motor Room Hydrogen Density ·
Tank Area 1 Hydrogen Density ·
Tank Area 2 Hydrogen Density |
| DTC No. | Active Test |
|---|---|
| P1DC100 | Control the Select Hydrogen Injector |
If any one of the hydrogen injectors does not close, malfunctioning injectors cannot be identified through an Active Test.
Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.
Accumulated hydrogen gas could ignite, resulting in a serious accident.
Click hereEngine / Hybrid System>FUEL>FUEL SYSTEM>PRECAUTION
This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.
When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Mode" is FC Working and "FC Intermittent Operation" is OFF. Then, wait 2 minutes or more.
Check that the "Low-Range Hydrogen Pressure (Filtered Value)" in the Data List is 280 kPa(abs) or less.
After completion of repair, check that no hydrogen leaks from the hydrogen system components with a hydrogen gas detector.
The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.
Pre-procedure1
None
Procedure1
According to the display on the GTS, check for DTCs in the Health Check.
| Result | Proceed to |
|---|---|
| Only P1DC100 is output | A |
| P1DC100 is output and DTCs other than the DTCs in the table below are output | B |
| P1DC100 is output and any DTCs in the table below are output | C |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Sensor and actuator circuit malfunction | P1D9A1C (FC) | Hydrogen Injector 1 Circuit Voltage Out of Range |
| P1DA01C (FC) | Hydrogen Injector 2 Circuit Voltage Out of Range | |
| P1DA51C (FC) | Hydrogen Injector 3 Circuit Voltage Out of Range | |
| P1DBA11 (FC) | Low-Range Hydrogen Pressure Sensor Circuit Short to Ground | |
| P1DBA15 (FC) | Low-Range Hydrogen Pressure Sensor Circuit Short to Battery or Open | |
P1DC100 may be store due to problems that cause the DTCs shown above to be output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order starting with the listed DTCs shown in the table above.
If DTC P1E407A or P1E4100 is output together with P1DC100, hydrogen may have leaked from the low-range hydrogen pressure components, or hydrogen may have been discharged by the low-range hydrogen pressure relief valve. After completion of repair, check for hydrogen leaks in the FC stack assembly.
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for 10 minutes or more.
NEXT
Pre-procedure1
None
Procedure1
Read the value displayed on the GTS.
| Tester Display |
|---|
| Low-Range Hydrogen Pressure (Filtered Value) |
| Result | Proceed to |
|---|---|
| When the ignition switch is turned to ON, "Low-Range Hydrogen Pressure (Filtered Value)" does not increase. | A |
| When the ignition switch is turned to ON, "Low-Range Hydrogen Pressure (Filtered Value)" increases to 160 kPa (abs) or higher. | B |
If the ignition switch is turned to ON and "Low-Range Hydrogen Pressure (Filtered Value)" increases, it may be due to poor closing of the hydrogen injector.
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
None
Procedure1
Using the GTS snapshot, record the values of the Data List items listed above.
| Tester Display |
|---|
| Tank Shut Valve 1 Drive Status |
| Tank Shut Valve 2 Drive Status |
| Tank Shut Valve 3 Drive Status |
| FC Work Mode |
| Hydrogen Injector 1 Injection Period |
| Hydrogen Injector 2 Injection Period |
| Hydrogen Injector 3 Injection Period |
| Target Low-Range Hydrogen Pressure |
| Low-Range Hydrogen Pressure (Filtered Value) |
Turn the ignition switch to ON (READY) and check that the Data List "FC Work Mode" is Working.
If DTCs are store and Working is disabled, record data from when the ignition switch is turned to ON until the FC system shuts down.
Check the "Low-Range Hydrogen Pressure (Filtered Value)" with the following conditions met.
FC Work Mode = Startup*1
Tank Shut Valve 1 Drive Status = Open
Tank Shut Valve 2 Drive Status = Open
Tank Shut Valve 3 Drive Status = Open
Hydrogen Injector 1 Injection Period = Value other than 0 μs*2
Hydrogen Injector 2 Injection Period = Value other than 0 μs*2
Hydrogen Injector 3 Injection Period = Value other than 0 μs*2
*1: If it can be started, check with "FC Work Mode" set to Working.
*2: If either "Hydrogen Injector 1 Injection Period", "Hydrogen Injector 2 Injection Period" or "Hydrogen Injector 3 Injection Period" shows a value other than 0 μs, an injection command is being sent to the injector.
| Result | Proceed to |
|---|---|
| When the hydrogen injector injection command is being given*1, "Low-Range Hydrogen Pressure (Filtered Value)" increases to a pressure higher than "Target Low-Range Hydrogen Pressure" by 50 kPa or more*2 | A |
| Other than above | B |
*1: If either Hydrogen Injector 1 Injection Period, Hydrogen Injector 2 Injection Period or Hydrogen Injector 3 Injection Period shows a value other than 0 μs, the injector can be determined that an injection command is being sent.
*2: Malfunction in the flow rate (larger than normal) of the hydrogen injector
If the Active Test shows that only a particular injector is malfunctioning, replace the malfunctioning injector.
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Remove the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor).
Reconnect the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor) connector.
Read the value displayed on the GTS.
| Tester Display |
|---|
| Low-Range Hydrogen Pressure (Filtered Value) |
Procedure1
Using the table, read the normal atmospheric pressure value for the applicable altitude.
| *a | Altitude, Temperature and Atmospheric Pressure Correlation Table | *b | Altitude (m (ft.)) |
| *c | Temperature (°C (°F)) | *d | Atmospheric Pressure (kPa (psi)) |
Standard atmospheric pressure is approximately 101 kPa (15 psi).
For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.
Compare the "Low-Range Hydrogen Pressure (Filtered Value)" values in the Data List with the normal atmospheric value from the table.
| Result | Proceed to |
|---|---|
| Difference between "Low-Range Hydrogen Pressure (Filtered Value)" in Data List and normal atmospheric pressure value is 35 kPa or more. | A |
| Other than above. | B |
Post-procedure1
Turn the ignition switch off.
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING