Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1E7B11  Air Shunt Valve Position Sensor Circuit Short to Ground  P1E7B15  Air Shunt Valve Position Sensor Circuit Short to Battery or Open  


DESCRIPTION

The opening sensor is installed on the air shunt valve to detect the opening angle of the valve as voltage.

This is a non-contact type sensor. As the valve closes, the sensor output voltage decreases and the sensor calculates the opening angle of the valve based on the signal which increases as the valve opens.

A477006E02
0.073,0.094 1.427,0.698 1.354,0.604 10 false Reference: Opening Sensor Characteristic Graph 1.594,0.604 2.365,0.802 0.771,0.198 10 false Voltage (V) 2.052,0.938 2.552,1.135 0.5,0.198 10 false 5.0 2.042,1.49 2.542,1.688 0.5,0.198 10 false 3.0 2.042,1.771 2.542,1.969 0.5,0.198 10 false 2.0 2.219,2.563 2.719,2.76 0.5,0.198 10 false 0.5 2.771,2.448 3.271,2.646 0.5,0.198 10 false 20 3.344,2.458 3.844,2.656 0.5,0.198 10 false 40 3.896,2.448 4.396,2.646 0.5,0.198 10 false 60 4.333,2.552 4.5,2.74 0.167,0.188 10 false 75 2.135,2.365 2.635,2.563 0.5,0.198 10 false 0 4.573,2.552 4.74,2.74 0.167,0.188 10 false 83 1.833,1.24 2.333,1.438 0.5,0.198 10 false 3.69 1.813,2.156 2.313,2.354 0.5,0.198 10 false 0.69 2.719,0.594 4.948,0.844 2.229,0.25 10 false Valve operation angle 2.781,0.188 4.896,0.438 2.115,0.25 10 false Valve control range 4.958,2.396 6.625,2.625 1.667,0.229 10 false Valve Opening Angle (°)

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E7B11 Air Shunt Valve Position Sensor Circuit Short to Ground If the +B voltage is not low when the ignition switch is ON, the output voltage of the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) circuit remains at less than 0.10 V for more than 3 seconds.
(1 trip detection logic)
·

FC air by-pass valve assembly (air shunt valve (opening angle sensor))

·

FC control ECU

·

Wire harness or connector


Master Warning: Comes on FC A
P1E7B15 Air Shunt Valve Position Sensor Circuit Short to Battery or Open If the +B voltage is not low when the ignition switch is ON, the output voltage of the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) circuit remains at more than 4.80 V for more than 3 seconds.
(1 trip detection logic)
·

FC air by-pass valve assembly (air shunt valve (opening angle sensor))

·

FC control ECU

·

Wire harness or connector


Master Warning: Comes on FC A

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List (EV)
"FC Work Mode"
Stop Startup Working Finishing
Data List (EV)
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection ○ ○ ○ ○ ○ -

Related Data List
DTC No. Data List
P1E7B11 Air Shunt Valve Position Sensor Voltage
P1E7B15

HINT:

If DTCs are found, read the "Air Shunt Valve Position Sensor Voltage" in the Data List on a GTS.


Air Shunt Valve Position Sensor Voltage Malfunction
Less than 0.10 V
·

Open in VABP (5 V power supply) circuit

·

Short in ABP circuit to ground

·

Short in ABP circuit to GABP (GND) circuit


Higher than 4.80 V
·

Short in VABP circuit to ABP circuit

·

Open in ABP circuit

·

Open in GABP (GND) circuit

·

Short in VABP circuit to ground



HINT:

It is suspected that malfunctions, or open/short circuits have occurred in the air shunt valve (opening angle sensor).


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))

Pre-procedure1

a.
A476968

Disconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B15)Location & Routing

Click Connector(B15)Engine Compartment>No. 2 Stack Wire>FC Air By-Pass Valve Assembly

B15-4 (VABP) - B15-5 (GABP) Ignition switch ON 4.75 to 5.25 V
B15-6 (ABP) - B15-5 (GABP) Ignition switch ON 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.



OK

2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))

NG

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))
2.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Disconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,B15)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(B15)Engine Compartment>No. 2 Stack Wire>FC Air By-Pass Valve Assembly

B1-120 (ABP) - B15-6 (ABP) Always Below 1 Ω
B1-119 (GABP) - B15-5 (GABP) Always Below 1 Ω
B1-118 (VABP) - B15-4 (VABP) Always Below 1 Ω
B1-120 (ABP) or B15-6 (ABP) - Body ground and other terminals Always 10 kΩ or higher
B1-118 (VABP) or B15-4 (VABP) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.


b.

Reconnect the FC control ECU connector.



OK

3.REPLACE FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR))

NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FC > Clear DTCs
50002 490
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FC > Trouble Codes
50001 490
Result:
Result Proceed to
P1E7B11 or P1E7B15 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

END

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))

Pre-procedure1

a.

Disconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.


b.
A476967

Disconnect the FC air pressure regulator assembly (air sealing valve (opening angle sensor)) connector.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B15)Location & Routing

Click Connector(B15)Engine Compartment>No. 2 Stack Wire>FC Air By-Pass Valve Assembly

B15-4 (VABP) - B15-5 (GABP) Ignition switch ON 4.75 to 5.25 V
B15-6 (ABP) - B15-5 (GABP) Ignition switch ON 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC air pressure regulator assembly (air sealing valve (opening angle sensor)) connector.


c.

Reconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.



OK

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE (OPENING ANGLE SENSOR))

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))
7.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))

Pre-procedure1

a.

Disconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.


b.
A476969

Disconnect the FC air pressure regulator assembly (air pressure regulating valve (opening angle sensor)) connector.


c.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B15)Location & Routing

Click Connector(B15)Engine Compartment>No. 2 Stack Wire>FC Air By-Pass Valve Assembly

B15-4 (VABP) - B15-5 (GABP) Ignition switch ON 4.75 to 5.25 V
B15-6 (ABP) - B15-5 (GABP) Ignition switch ON 4.75 to 5.25 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the FC air pressure regulator assembly (air pressure regulating valve (opening angle sensor)) connector.


c.

Reconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.



OK

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE (OPENING ANGLE SENSOR))

NG

8.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))
8.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE (OPENING ANGLE SENSOR)))

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Disconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,B15)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(B15)Engine Compartment>No. 2 Stack Wire>FC Air By-Pass Valve Assembly

B1-120 (ABP) - B15-6 (ABP) Always Below 1 Ω
B1-119 (GABP) - B15-5 (GABP) Always Below 1 Ω
B1-118 (VABP) - B15-4 (VABP) Always Below 1 Ω
B1-120 (ABP) or B15-6 (ABP) - Body ground and other terminals Always 10 kΩ or higher
B1-118 (VABP) or B15-4 (VABP) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC air by-pass valve assembly (air shunt valve (opening angle sensor)) connector.


b.

Reconnect the FC control ECU connector.



OK

9.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE (OPENING ANGLE SENSOR)))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE (OPENING ANGLE SENSOR)))

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Disconnect the FC air pressure regulator assembly (air pressure regulating valve (opening angle sensor)) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,B16)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(B16)Engine Compartment>No. 2 Stack Wire>FC Air Pressure Regulator Assembly (Air Pressure Regulation Valve)

B1-72 (VAVP) - B16-2 (VAVP) Always Below 1 Ω
B1-72 (VAVP) or B16-2 (VAVP) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC air pressure regulator assembly (air pressure regulating valve (opening angle sensor)) connector.


b.

Reconnect the FC control ECU connector.



OK

10.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE (OPENING ANGLE SENSOR)))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (FC CONTROL ECU - FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE (OPENING ANGLE SENSOR)))

Pre-procedure1

a.

Disconnect the FC control ECU connector.


b.

Disconnect the FC air pressure regulator assembly (air sealing valve (opening angle sensor)) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1,B14)Location & Routing

Click Connector(B1)Engine Compartment>No. 2 Stack Wire>FC Control ECU

Click Connector(B14)Engine Compartment>No. 2 Stack Wire>FC Air Pressure Regulator Assembly (Air Shut Valve)

B1-97 (VASP) - B14-2 (VASP) Always Below 1 Ω
B1-97 (VASP) or B14-2 (VASP) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC air pressure regulator assembly (air sealing valve (opening angle sensor)) connector.


b.

Reconnect the FC control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR