Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D0F62  Cell Monitor Voltage/FC Converter Input Voltage Signal Compare Failure  


DESCRIPTION

Refer to high voltage system diagram for the System Description.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION

The FC boost control ECU detects high voltage before boosting (FVL) using the voltage sensor which is located inside the FC converter assembly. In addition, the FC control ECU detects FC total voltage (cell monitor voltage (FVC)) using the cell monitor, which is located inside the FC stack assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D0F62 Cell Monitor Voltage/FC Converter Input Voltage Signal Compare Failure The difference between the cell monitor voltage (FVH) and the FC converter input voltage (FVL) is too large.
(1 trip detection logic)
·

FC converter assembly

·

FC stack assembly

·

Wire harness or connector


Master Warning: Comes on FCDC B

Related Data List
DTC No. System Data List
P1D0F62 FCDC FC Voltage (Filtered Value)
EV Total Voltage

WIRING DIAGRAM

Refer to the wiring diagram for the high-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON.

2.

Enter the following menus: Powertrain / EV / Data List / FC Work Mode, FC Intermittent Operation.

3.

Put the state in park (P), turn the ignition switch to ON (READY) and wait until the FC system is activated (Waiting for at least 2 minutes is required after turning the ignition switch to ON (READY)).

FC system is activated: Data List shows that "FC Work Mode" is "Working" and "FC Intermittent Operation" is "OFF".


4.

Wait at least 15 seconds with the FC system activated.

5.

Drive the vehicle forward with the shift state in drive (D) for 5 m (16 ft.) or more.

6.

Drive the vehicle backward with the shift state in reverse (R) for 5 m (16 ft.) or more.



PROCEDURE

1.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1D0F62 is output A
P1D0F62 and DTCs other than the DTCs in the table below are output B
P1D0F62 and any DTCs in the table below are output C


Malfunction Content Relevant DTC
Communication system malfunction U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message
Sensor and actuator circuit malfunction P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold

HINT:

DTC P1D0F62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (EV)

B

2.CHECK DTC OUTPUT (EV)

C

GO TO DTC CHART

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

Connect the GTS to the DLC3.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B


Malfunction Content Relevant DTC
Microcomputer malfunction/Power source circuit malfunction P1DCF96 Cell Monitor Component Internal Failure

HINT:

DTC P1D0F62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

3.CLEAR DTC

B

GO TO DTC CHART

3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

5.CHECK DTC OUTPUT (FCDC)
5.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Communication system malfunction U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message
Sensor and actuator circuit malfunction P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold


HINT:

DTC P1D0F62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

6.CHECK DTC OUTPUT (EV)

B

GO TO DTC CHART

6.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B


Malfunction Content Relevant DTC
Microcomputer malfunction/Power source circuit malfunction P1DCF96 Cell Monitor Component Internal Failure

HINT:

DTC P1D0F62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

7.SIMULATION TEST (FCDC)

B

GO TO DTC CHART

7.SIMULATION TEST (FCDC)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


b.

Drive the vehicle for approximately 10 minutes referring to the following freeze frame data.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B

Malfunction Content Relevant DTC
Communication system malfunction U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message
Sensor and actuator circuit malfunction P1D2017 FC Converter Input Voltage Sensor Circuit Voltage Above Threshold


HINT:

DTC P1D0F62 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

8.SIMULATION TEST (EV)

B

GO TO DTC CHART

8.SIMULATION TEST (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
Any of the DTCs in the table below are output B


Malfunction Content Relevant DTC
Microcomputer malfunction/Power source circuit malfunction P1DCF96 Cell Monitor Component Internal Failure

HINT:

DTC P1D0F62 may be output as a result of the malfunction indicated by the DTCs above.



Post-procedure1

a.

Turn the ignition switch off.



A

9.READ VALUE USING GTS

B

GO TO DTC CHART

9.READ VALUE USING GTS
HINT:

Perform the inspection with the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) connected.


Pre-procedure1

a.

Turn the ignition switch off and wait for 18 hours or more.

HINT:

Waiting for at least 18 hours is required to discharge the FC stack assembly and FC converter assembly to 0 V.



Procedure1

a.

Read the Data List.

Powertrain > FCDC > Data List
Tester Display
FC Voltage (Filtered Value)
50003 493 6
Result:
Result Proceed to
The value of FC Voltage (Filtered Value) is less than 10 V A
The value of FC Voltage (Filtered Value) is 10 V or more B



Post-procedure1

a.

None



A

10.READ VALUE USING GTS

B

16.READ VALUE USING GTS
10.READ VALUE USING GTS
HINT:

Perform the inspection with the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) connected.


Pre-procedure1

a.

None


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Total Voltage
50003 397 929
Result:
Result Proceed to
The value of Total Voltage is less than 10 V A
The value of Total Voltage is 10 V or more B



Post-procedure1

a.

Turn the ignition switch off.



A

11.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

B

REPLACE FC STACK ASSEMBLY

11.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

12.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P19FD73

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

13.CHECK FC CONVERTER ASSEMBLY (FC STACK ASSEMBLY CONNECTION CONDITION)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK FC CONVERTER ASSEMBLY (FC STACK ASSEMBLY CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to EV supply battery assembly and the FC converter power outlet cable (inverter with converter assembly) is not connected to the FC converter assembly.

NOTICE:

After removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the FC stack assembly from the vehicle.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL



c.

Remove the front FC converter service hole cover, No. 1 FC stack case plug and FC converter vent cover from the FC converter assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL



Procedure1

a.
A480010

A480002

Check that the bolts for the FC converter assembly are tightened to the specified torque, the FC converter assembly is connected securely, and there are no contact problems.

Standard:
Item Specified Condition
Torque 14.0 N*m
143 kgf*cm
124 in.*lbf



b.

Remove the FC converter assembly from the FC stack assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL



c.

Check for arc marks at the terminals for the FC converter assembly.


Result:
Result Proceed to
The terminals are connected securely and there are no contact problems There are no arc marks A
The terminals are not connected securely and there is a contact problem There are arc marks B
The terminals are connected securely and there are no contact problems There are arc marks
The terminals are not connected securely and there is a contact problem There are no arc marks C


Post-procedure1

a.

Install the FC converter assembly to the FC stack assembly.


b.

Install the front FC converter service hole cover, No.1 FC stack case plug and FC converter vent cover from the FC converter assembly.


c.

Install the FC stack assembly to the vehicle.



A

14.CLEAR DTC

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

14.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

15.CHECK DTC OUTPUT (FCDC)
15.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
OK:

DTCs are not output.


Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

16.READ VALUE USING GTS
HINT:

Perform the inspection with the service plug grip connected.


Pre-procedure1

a.

None


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Total Voltage
50003 397 929
Result:
Result Proceed to
The value of Total Voltage is less than 10 V A
The value of Total Voltage is 10 V or more B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE FC CONVERTER ASSEMBLY

B

REPLACE FC CONVERTER ASSEMBLY AND FC STACK ASSEMBLY