Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AA649  Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure  P1C7C49  Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure  P1C7D49  Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure  P1C7E49  Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure  P1C7F49  Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure  P1EEC49  Hybrid/EV Battery Voltage System Isolation (FC Air Compressor Area) Internal Electronic Failure  P1EED49  Hybrid/EV Battery Voltage System Isolation (FC Area) Internal Electronic Failure  P1EEE49  Hybrid/EV Battery Voltage System Isolation (Hydrogen Pump Area) Internal Electronic Failure  P1EEF49  Hybrid/EV Battery Voltage System Isolation (FC Coolant Pump Area) Internal Electronic Failure  


DESCRIPTION

The EV control ECU monitors the battery ECU assembly and detects insulation malfunctions in the high-voltage system.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0AA649 Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure Insulation resistance between the high-voltage circuit and the body has decreased.*1
(1 trip detection logic)
·

Inverter with converter assembly

·

Electric heater sub-assembly

·

FC converter assembly

·

FC stack assembly

·

FC cooling water pump assembly

·

FCV with motor transaxle assembly

·

FC air compressor with motor assembly

·

FC coolant (Toyota genuine FC stack coolant)

·

FC cooling water ion exchanger element

·

FC air compressor motor cable assembly

·

No. 1 battery pack wire

·

Motor cable

·

Front compartment main wire

·

No. 2 battery pack wire

·

FC cooling water pump cable

·

Hydrogen recirculation pump assembly

·

Compressor with motor assembly

·

FC hydrogen pump inverter assembly

·

FC cooling water pump inverter assembly

·

Floor under wire

·

FC junction cable

·

No. 1 EV battery junction block assembly

·

FC inverter input terminal

·

Air conditioning compressor cable


Master Warning:
Comes on
EV A
P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure Insulation resistance of the compressor with motor assembly or air conditioning inverter has decreased.*2
(1 trip detection logic)
Air conditioning system Master Warning:
Comes on
EV A
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure Insulation resistance of the EV supply battery, battery ECU assembly or SMR has decreased.*2
(1 trip detection logic)
·

No. 1 EV battery junction block assembly

·

Battery ECU assembly

·

Battery voltage sensor (for upper side)

·

Battery voltage sensor (for lower side)

·

EV battery terminal block

·

No. 1 EV supply stack sub-assembly

·

No. 2 EV supply stack sub-assembly


Master Warning:
Comes on
EV A
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure Insulation resistance of the FCV with motor transaxle assembly or inverter with converter assembly has decreased.*2
(1 trip detection logic)
·

FCV with motor transaxle assembly

·

Inverter with converter assembly


Master Warning:
Comes on
EV A
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure Insulation resistance of the drive motor, FC air compressor with motor assembly, FC cooling water pump assembly, hydrogen recirculation pump assembly, A/C inverter, SMR or FC stack main relay has decreased.*2
(1 trip detection logic)
·

Inverter with converter assembly

·

Electric heater sub-assembly

·

FC converter assembly

·

No. 1 battery pack wire

·

Motor cable

·

Front compartment main wire

·

No. 2 battery pack wire

·

FC cooling water pump cable

·

Air conditioning system

·

FC hydrogen pump inverter assembly

·

FC cooling water pump inverter assembly

·

Floor under wire

·

FC junction cable

·

No. 1 EV battery junction block assembly


Master Warning:
Comes on
EV A
P1EEC49 Hybrid/EV Battery Voltage System Isolation (FC Air Compressor Area) Internal Electronic Failure Insulation resistance of the FC air compressor with motor assembly or inverter for the FC air compressor motor has decreased.*2
(1 trip detection logic)
·

FC air compressor with motor assembly

·

Inverter with converter assembly


Master Warning:
Comes on
EV A
P1EED49 Hybrid/EV Battery Voltage System Isolation (FC Area) Internal Electronic Failure Insulation resistance of the FC stack assembly, FC coolant or FC converter assembly has decreased.*2
(1 trip detection logic)
·

FC coolant (Toyota genuine FC stack coolant)

·

FC cooling water ion exchanger element

·

FC converter with FC stack assembly


Master Warning:
Comes on
EV A
P1EEE49 Hybrid/EV Battery Voltage System Isolation (Hydrogen Pump Area) Internal Electronic Failure When the insulation resistance of the hydrogen recirculation pump assembly, or the insulation resistance inside the FC hydrogen pump inverter assembly, has decreased.*2
(1 trip detection logic)
·

Hydrogen recirculation pump assembly

·

FC hydrogen pump inverter assembly

·

FC cooling water pump inverter assembly


Master Warning:
Comes on
EV A
P1EEF49 Hybrid/EV Battery Voltage System Isolation (FC Coolant Pump Area) Internal Electronic Failure When the insulation resistance of the FC cooling water pump assembly, or the insulation resistance inside the FC cooling water pump inverter assembly, has decreased.*2
(1 trip detection logic)
·

FC cooling water pump assembly

·

FC cooling water pump inverter assembly

·

FC hydrogen pump inverter assembly


Master Warning:
Comes on
EV A

HINT:
·

*1: The insulation malfunction detection circuit in the battery ECU assembly monitors the insulation resistance between the high voltage circuits and body. If the insulation resistance decreases, the EV control ECU stores DTC P0AA649 and illuminates the master warning light regardless of malfunction area.

Sometimes the insulation malfunction is hard to duplicate due to the vehicle's condition changing. So if DTC P0AA649 outputs, complete the following steps as soon as possible.

·

*2: If the following operations are performed within the same trip after DTC P0AA649 is stored, just one of the related DTCs (P1C7C49, P1C7D49, P1C7E49, P1C7F49, P1EEC49, P1EED49, P1EEE49 or P1EEF49) will be stored.

(a)

Apply the parking brake firmly.

(b)

Wait for 5 minutes or more with the vehicle stopped, the ignition switch to ON (READY), push the P position switch and the air conditioning system on (Lo/MAX COOL, blower speed HI).

(c)

Turn the ignition switch off and wait for 10 minutes or more.

HINT:
·

DTCs and freeze frame data are useful information in determining the malfunctioning part. Before performing diagnosis, make sure to check and make a note of all output DTCs and freeze frame data. (Even if a high-voltage insulation malfunction cannot be reproduced, once stored, DTCs of insulation will not be cleared unless the clear operation is performed.)

·

When the insulation resistance of the EV supply battery area decreases and the ignition switch is turned to ON, DTC P1C7D49 is stored within 2 minutes.




·

When measuring insulation resistance using a megohmmeter, measure the resistance while jiggling the high voltage wire harness.



Related Data List (Reproduction of Phenomenon and Check)
DTC No. Data List
P0AA649
·

Short Wave Highest Value Level

·

Hybrid/EV Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Boost Ratio

·

A/C Consumption Power

·

SMRP Status

·

SMRB Status

·

SMRG Status

·

Motor Inverter Shutdown Status

·

FC Air Compressor Gate Shutdown Request

·

Boosting Converter Gate Shutdown Request

·

Insulation Resistance Division Check Completion using MG Inv

·

Insulation Resistance Division Check Completion using A/C Inv

·

Insulation Resistance Division Check Completion using SMR

·

Short Wave Highest Value Availability just after MG Inv On/Off

·

Short Wave Highest Value Availability just after A/C Inv On/Off

·

Short Wave Highest Value Availability just after SMR On/Off

·

FC Air Compressor Area Insulation Resistance Division Check Completion

·

FC Coolant Pump Area Insulation Resistance Division Check Completion

·

Hydrogen Pump Area Insulation Resistance Division Check Completion

·

FC Area Insulation Resistance Division Check Completion

·

Motor Area Insulation Resistance Division Check Completion

·

A/C Area Insulation Resistance Division Check Completion

·

Hybrid/EV Battery Area Insulation Resistance Division Check Completion

·

FC Coolant Pump Consumption Power

·

FC Positive Relay Drive Status

·

FC Negative Relay Drive Status

·

FC Precharge Relay Status

·

FC Coolant Pump Consumption Power


P1C7C49
P1C7D49
P1C7E49
P1C7F49
P1EEC49
P1EED49
P1EEE49
P1EEF49

Use the following items as a reference when duplicating the vehicle conditions at the time when the malfunction occurred.

Data List
·

Ready Signal

·

Vehicle Speed

·

BATT Voltage

·

Distance from DTC Cleared

·

Engine Run Time

·

Hybrid/EV Battery SOC


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure. (Do not turn the ignition switch off (READY off) during this inspection.)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Apply the parking brake and secure the wheels using chocks.

2.

When the vehicle is stationary, turn the ignition switch to ON (READY) with push the P position switch and wait for 10 minute or more.

NOTICE:

If "FC System Periodic Check in Progress" is displayed on the multi-information display inside the combination meter, wait until "FC System Periodic Check Completed" is displayed. Waiting for at least 8 minutes is required until "FC System Check Complete" is displayed. The waiting time will be longer if the temperature of the FC coolant is high, such as immediately after the vehicle had been driven.


3.

Turn the air conditioning system on (MAX COLD, blower speed HI).

4.

Push the P position switch and wait for 5 minutes.

-

If the following operations are performed in the same trip after DTC P0AA649 is stored, theparts with insufficient resistance will be determined, and an additional DTC (P1C7C49, P1C7D49, P1C7E49, P1C7F49, P1EEC49, P1EED49, P1EEE49 or P1EEF49) will likely be stored.

-

Operations to determine the part with insufficient insulation resistance

Wait for 5 minutes or more with the vehicle stopped, the ignition switch to ON (READY), push the P position switch and the air conditioning system on (Lo/COOL MAX, blower speed HI), then turn the ignition switch off and wait for 10 minutes or more.

-

If no DTCs are output, proceed to the next step.

NOTICE:

Power is supplied to the drive motor only when the vehicle is driven. If a drop in insulation resistance is detected in the transaxle assembly area, perform the following procedure to drive the vehicle as DTC P0AA649 will not be output unless the vehicle is driven with the shift lever in D.



5.

Drive the vehicle for approximately 5 minutes referring to the following freeze frame data items: "Vehicle Speed", "Shift Position", "Accelerator Position Sensor No.1 Voltage %", "Engine Speed", "Coolant Temperature", "Master Cylinder Control Torque", "Inverter Coolant Water Temperature", "Motor Inverter Temperature" and "FC Air Compressor Inverter Temperature"

(If the freeze frame data item "Vehicle Speed" is 10 km/h (6 mph) or less, drive the vehicle at 10 km/h (6 mph) or more.)

-

If the following operations are performed in the same trip after DTC P0AA649 is stored, the parts within sufficient insulation resistance will be determined, and a DTC (P1C7C49, P1C7D49, P1C7E49, P1C7F49, P1EEC49, P1EED49, P1EEE49 or P1EEF49) will likely be stored.

-

Operations to determine the part with insufficient insulation resistance

When the vehicle is stationary, turn the ignition switch to ON (READY) with the push the P position switch and the air conditioning system on (Lo/COOL MAX, blower speed HI), and wait for 5 minutes or more. Then turn the ignition switch off (READY not on) and wait for 5 minutes or more.

HINT:

If a DTC is not output, check the driving condition that the Data List item (Short Wave Highest Val) decreases.





WIRING DIAGRAM

A479469N01
0.604,1.74 0.917,1.938 0.313,0.198 10 false *1 1.167,1.75 1.479,1.948 0.313,0.198 10 false *2 1.333,2.833 1.646,3.031 0.313,0.198 10 false *3 1.854,2 2.167,2.198 0.313,0.198 10 false *4 1.833,2.802 2.146,3 0.313,0.198 10 false *5 1.844,3.26 2.156,3.458 0.313,0.198 10 false *6 2.542,3.167 2.854,3.365 0.313,0.198 10 false *7 3.927,1.135 4.24,1.333 0.313,0.198 10 false *8 4.969,1.135 5.281,1.333 0.313,0.198 10 false *9 4.375,1.917 4.688,2.115 0.313,0.198 10 false *10 4.24,3.885 4.552,4.083 0.313,0.198 10 false *11 5.74,2.479 6.052,2.677 0.313,0.198 10 false *12 0.156,0.094 0.469,0.292 0.313,0.198 10 false *a 6.052,4.323 6.365,4.521 0.313,0.198 10 false *13 2.24,4.938 2.552,5.135 0.313,0.198 10 false *14 1.313,4.927 1.625,5.125 0.313,0.198 10 false *15 0.729,4.885 1.042,5.083 0.313,0.198 10 false *16 2.302,6.156 2.615,6.354 0.313,0.198 10 false *17 2.313,7.146 2.625,7.344 0.313,0.198 10 false *18 1.302,6.167 1.615,6.365 0.313,0.198 10 false *19 1.333,7.146 1.646,7.344 0.313,0.198 10 false *20 3.302,0.958 3.615,1.156 0.313,0.198 10 false *g 5.573,0.948 5.885,1.146 0.313,0.198 10 false *e 0.438,4.875 0.75,5.073 0.313,0.198 10 false *c 0.781,7.073 1.094,7.271 0.313,0.198 10 false *j 0.75,6.146 1.063,6.344 0.313,0.198 10 false *i 0.635,1.302 0.948,1.5 0.313,0.198 10 false *h 6.354,1.698 6.667,1.896 0.313,0.198 10 false *f 3.469,0.323 3.781,0.521 0.313,0.198 10 false *b 0.146,8.083 0.458,8.281 0.313,0.198 10 false *A 2.094,8.073 2.406,8.271 0.313,0.198 10 false *B 3.76,8.073 4.073,8.271 0.313,0.198 10 false *C 5.156,8.052 5.469,8.25 0.313,0.198 10 false *D 6.635,8.042 6.948,8.24 0.313,0.198 10 false *E 6.917,8.042 7.104,8.229 0.188,0.188 10 false *F

A484697C01
3.896,4.927 4.208,5.125 0.313,0.198 10 false *b 2.635,1.677 2.948,1.875 0.313,0.198 10 false *21 4.01,1.656 4.323,1.854 0.313,0.198 10 false *22 4.49,1.667 4.802,1.865 0.313,0.198 10 false *23 5.24,1.542 5.552,1.74 0.313,0.198 10 false *24 3.542,2.771 3.854,2.969 0.313,0.198 10 false *25 4.344,4.292 4.656,4.49 0.313,0.198 10 false *28 3.656,3.292 3.969,3.49 0.313,0.198 10 false *27 3.271,3.292 3.583,3.49 0.313,0.198 10 false *26 4.656,2.292 4.969,2.49 0.313,0.198 10 false *7 5.531,3.563 5.844,3.76 0.313,0.198 10 false *d 0.563,0.219 0.875,0.417 0.313,0.198 10 false *A 0.958,0.219 1.271,0.417 0.313,0.198 10 false *B 2.938,0.229 3.25,0.427 0.313,0.198 10 false *C 4.313,0.219 4.625,0.417 0.313,0.198 10 false *D 6.24,0.229 6.552,0.427 0.313,0.198 10 false *E 6.563,0.229 6.875,0.427 0.313,0.198 10 false *F
*1 FC Stack Assembly *2 FC Converter Assembly
*3 FC Boost Control ECU *4 FCRB
*5 FCRP *6 FCRG
*7 System Main Resistor *8 FC Air Compressor with Motor Assembly
*9 FCV with Motor Transaxle Assembly *10 Inverter
*11 Boost Converter *12 Inverter with Converter Assembly
*13 Electric Heater Sub-assembly *14 A/C Inverter
*15 A/C Motor *16 Compressor with Motor Assembly
*17 Hydrogen Recirculation Pump Inverter Assembly *18 FC Cooling Water Pump Inverter Assembly
*19 Hydrogen Recirculation Pump Assembly *20 FC Cooling Water Pump Assembly
*21 SMRB *22 SMRG
*23 SMRP *24 EV Supply Assembly
*25 Battery ECU Assembly *26 Battery Voltage Sensor (for Lower Side)
*27 Battery Voltage Sensor (for Upper Side) *28 Service Plug Grip
*a High-voltage Areas *b DTC P0AA649 Vehicle Insulation Resistance Reduction Area
*c DTC P1C7C49 Air Conditioning System Area *d DTC P1C7D49 EV Supply Battery Area
*e DTC P1C7E49 FCV with Motor Transaxle Assembly or Inverter with Converter Assembly AC (Alternation Current) Section Area *f DTC P1C7F49 High Voltage Direct Current Area
*g DTC P1EEC49 FC Air Compressor with Motor Assembly or Inverter with Converter Assembly AC (Alternation Current) Section Area *h DTC P1EED49 FC Stack Area
*i DTC P1EEE49 Hydrogen Recirculation Pump Assembly or Hydrogen Recirculation Pump Inverter Assembly AC (Alternation Current) Section Area *j DTC P1EEF49 FC Cooling Water Pump Assembly, FC Cooling Water Pump Cable or FC Cooling Water Pump Inverter Assembly AC (Alternation Current) Section Area


A484696E01
3,4.042 5.635,4.271 2.635,0.229 10 false NO.1 EV Battery Junction Block Assembly 0.313,1.854 1.563,2.219 1.25,0.365 10 false EV Battery Terminal Block 0.198,1.135 1.667,1.5 1.469,0.365 10 false No. 2 EV Supply Stack Sub-assembly 0.167,2.823 1.604,3.198 1.438,0.375 10 false No. 1 EV Supply Stack Sub-assembly 0.469,3.844 1.667,4.031 1.198,0.188 10 false Service Plug Grip 1.083,5.354 3.99,5.552 2.906,0.198 10 false : High Voltage Line 1.938,1.677 2.396,1.875 0.458,0.198 10 false Z19 1.938,2.365 2.396,2.563 0.458,0.198 10 false Z18 4.208,1.115 4.667,1.313 0.458,0.198 10 false SMRB 4.198,2.104 4.656,2.302 0.458,0.198 10 false SMRG 4.198,3.135 4.656,3.333 0.458,0.198 10 false SMRP 3.198,3.073 4.021,3.521 0.823,0.448 10 false System Main Resistor 2.625,0.771 3.083,0.969 0.458,0.198 10 false Z13 2.625,1.76 3.083,1.958 0.458,0.198 10 false Z12 5.771,0.781 6.229,0.979 0.458,0.198 10 false N1 5.76,1.76 6.219,1.958 0.458,0.198 10 false N2 2.688,0.573 2.844,0.771 0.156,0.198 10 false 1 1.74,1.667 1.896,1.865 0.156,0.198 10 false 1 1.729,2.375 1.885,2.573 0.156,0.198 10 false 1 2.688,1.552 2.844,1.75 0.156,0.198 10 false 1 5.792,0.573 5.948,0.771 0.156,0.198 10 false 1 5.792,1.552 5.948,1.75 0.156,0.198 10 false 1 5.406,1.604 5.865,1.802 0.458,0.198 10 false CEI 5.396,0.625 5.854,0.823 0.458,0.198 10 false CBI 6.542,0.781 6.698,0.979 0.156,0.198 10 false A 6.521,1.76 6.677,1.958 0.156,0.198 10 false B 2.979,1.604 3.135,1.802 0.156,0.198 10 false - 2.958,0.635 3.115,0.833 0.156,0.198 10 false +

A479475E01
2.135,0.615 2.375,0.76 0.24,0.146 10 false N3 2.135,1.042 2.375,1.188 0.24,0.146 10 false N3 2.115,1.979 2.354,2.125 0.24,0.146 10 false z30 2.104,2.5 2.344,2.646 0.24,0.146 10 false z30 2.104,3.052 2.344,3.198 0.24,0.146 10 false z30 2.135,4.885 2.375,5.031 0.24,0.146 10 false b1 2.146,5.615 2.385,5.76 0.24,0.146 10 false b1 2.125,6.344 2.365,6.49 0.24,0.146 10 false b1 4.031,0.604 4.271,0.75 0.24,0.146 10 false x2 4.031,1.021 4.271,1.167 0.24,0.146 10 false x2 4.031,1.438 4.271,1.583 0.24,0.146 10 false x2 5.344,0.615 5.583,0.76 0.24,0.146 10 false x1 5.344,1.021 5.583,1.167 0.24,0.146 10 false x1 5.344,1.438 5.583,1.583 0.24,0.146 10 false x1 4.021,2.76 4.26,2.906 0.24,0.146 10 false z31 4.021,3.188 4.26,3.333 0.24,0.146 10 false z31 4.031,6.271 4.271,6.417 0.24,0.146 10 false b4 4.031,7.25 4.271,7.396 0.24,0.146 10 false b4 2.427,0.615 2.885,0.813 0.458,0.198 10 false CBI 2.427,1.01 2.885,1.208 0.458,0.198 10 false CEI 2.448,2 2.667,2.167 0.219,0.167 10 false U 2.448,2.521 2.667,2.688 0.219,0.167 10 false V 2.427,3.052 2.646,3.219 0.219,0.167 10 false W 0.969,4.865 1.188,5.031 0.219,0.167 10 false U 0.979,5.635 1.198,5.802 0.219,0.167 10 false V 0.948,6.344 1.167,6.51 0.219,0.167 10 false W 0.771,0.594 0.99,0.76 0.219,0.167 10 false A 0.781,1.01 1,1.177 0.219,0.167 10 false B 3.75,0.594 3.969,0.76 0.219,0.167 10 false P 3.729,1.021 3.948,1.188 0.219,0.167 10 false N 3.458,1.438 3.917,1.625 0.458,0.188 10 false C-OFF 3.552,2.76 3.969,2.917 0.417,0.156 10 false F-VH 3.646,3.188 3.99,3.333 0.344,0.146 10 false F-N 3.552,3.615 3.969,3.792 0.417,0.177 10 false SHLD 0.125,3.458 1.594,3.896 1.469,0.438 10 false Hydrogen Recirculation Pump Aaaembly 0.104,7.438 1.219,7.823 1.115,0.385 10 false FC Cooling Water Pump Assembly 0.115,7.26 0.354,7.406 0.24,0.146 10 false b2 1.24,8.542 2.594,8.74 1.354,0.198 10 false : High Voltage Line 2.438,8.219 4.042,8.458 1.604,0.24 10 false FC Converter Assembly 5.323,7.875 5.563,8.021 0.24,0.146 10 false b3 5.313,8.031 6.74,8.396 1.427,0.365 10 false Compressor with Motor Assembly 5.229,6.271 5.448,6.438 0.219,0.167 10 false N 5.229,7.229 5.448,7.396 0.219,0.167 10 false P 3.729,6.26 3.948,6.427 0.219,0.167 10 false N 3.76,7.24 3.979,7.406 0.219,0.167 10 false P 5.656,3.594 6.073,3.771 0.417,0.177 10 false SHLD 5.656,3.188 6,3.333 0.344,0.146 10 false F-N 5.656,2.771 6.073,2.927 0.417,0.156 10 false F-VH 5.646,1.448 6.104,1.635 0.458,0.188 10 false C-OFF 5.656,1.021 5.875,1.188 0.219,0.167 10 false N 5.656,0.594 5.875,0.76 0.219,0.167 10 false P 4.042,0.406 4.229,0.573 0.188,0.167 10 false 1 5.375,0.417 5.563,0.583 0.188,0.167 10 false 1 4.083,2.552 4.271,2.719 0.188,0.167 10 false 1 2.177,1.792 2.365,1.958 0.188,0.167 10 false 1 2.146,6.135 2.333,6.302 0.188,0.167 10 false 1 4.073,6.083 4.26,6.25 0.188,0.167 10 false 1 4.052,0.844 4.24,1.01 0.188,0.167 10 false 2 4.063,1.26 4.25,1.427 0.188,0.167 10 false 3 5.375,0.844 5.563,1.01 0.188,0.167 10 false 2 5.375,1.271 5.563,1.438 0.188,0.167 10 false 3 4.063,3 4.25,3.167 0.188,0.167 10 false 2 2.156,0.406 2.344,0.573 0.188,0.167 10 false 2 2.167,0.833 2.354,1 0.188,0.167 10 false 1 2.167,2.323 2.354,2.49 0.188,0.167 10 false 2 2.177,2.865 2.365,3.031 0.188,0.167 10 false 3 2.177,4.698 2.365,4.865 0.188,0.167 10 false 3 2.167,5.417 2.354,5.583 0.188,0.167 10 false 2 4.063,7.063 4.25,7.229 0.188,0.167 10 false 2 5.031,7.104 5.219,7.271 0.188,0.167 10 false 2 5.01,6.115 5.198,6.281 0.188,0.167 10 false 1 1.219,4.74 1.406,4.906 0.188,0.167 10 false 3 1.219,5.479 1.406,5.646 0.188,0.167 10 false 2 1.229,6.208 1.417,6.375 0.188,0.167 10 false 1 5.594,4.552 6.948,4.958 1.354,0.406 10 false Inverter with Converter Assembly 4.292,8.573 5.156,8.76 0.865,0.188 10 false *: Shielded 4.563,6.885 4.698,7.063 0.135,0.177 10 false * 4.573,5.896 4.708,6.073 0.135,0.177 10 false * 1.604,6.125 1.74,6.302 0.135,0.177 10 false * 1.604,5.427 1.74,5.604 0.135,0.177 10 false * 1.583,4.656 1.719,4.833 0.135,0.177 10 false * 4.719,2.438 4.854,2.615 0.135,0.177 10 false * 4.698,0.302 4.833,0.479 0.135,0.177 10 false * 2.448,4.896 2.667,5.063 0.219,0.167 10 false U 2.448,5.604 2.667,5.771 0.219,0.167 10 false V 2.438,6.354 2.656,6.521 0.219,0.167 10 false W

for LHD:
A479476E01
0.875,8.375 2.115,8.573 1.24,0.198 10 false : High Voltage Line 0.156,3.458 0.469,3.656 0.313,0.198 10 false q1 1.635,1.094 1.948,1.292 0.313,0.198 10 false q2 1.625,1.75 1.938,1.948 0.313,0.198 10 false q2 1.625,2.417 1.938,2.615 0.313,0.198 10 false q2 1.625,3.063 1.938,3.26 0.313,0.198 10 false q2 2.344,1.115 2.656,1.313 0.313,0.198 10 false O3 2.333,1.781 2.646,1.979 0.313,0.198 10 false O3 2.323,2.438 2.635,2.635 0.313,0.198 10 false O3 3.073,1.115 3.385,1.313 0.313,0.198 10 false O2 3.073,1.771 3.385,1.969 0.313,0.198 10 false O2 3.063,2.438 3.375,2.635 0.313,0.198 10 false O2 3.083,5.031 3.396,5.229 0.313,0.198 10 false o3 3.083,5.76 3.396,5.958 0.313,0.198 10 false o3 3.073,6.5 3.385,6.698 0.313,0.198 10 false o3 4.531,3.552 4.844,3.75 0.313,0.198 10 false A32 4.542,5.042 4.854,5.24 0.313,0.198 10 false A32 0.156,3.625 1.156,4.177 1,0.552 10 false FCV with Motor Transaxle Assembly 0.26,7.219 0.573,7.417 0.313,0.198 10 false o1 0.25,7.406 1.729,7.813 1.479,0.406 10 false FC Air Compressor with Motor Assembly 2.896,7.51 5.177,7.698 2.281,0.188 10 false Inverter with Converter Assembly 5.792,5.844 6.104,6.042 0.313,0.198 10 false O4 5.781,6.021 6.75,6.406 0.969,0.385 10 false Electric Heater Sub-assembly 0.813,1.125 1.01,1.292 0.198,0.167 10 false U 0.823,1.771 1.021,1.938 0.198,0.167 10 false V 0.823,2.406 1.021,2.573 0.198,0.167 10 false W 1.792,5.042 1.99,5.208 0.198,0.167 10 false U 1.802,5.771 2,5.938 0.198,0.167 10 false V 1.781,6.49 1.979,6.656 0.198,0.167 10 false W 3.396,1.125 3.771,1.292 0.375,0.167 10 false R-U 3.396,1.771 3.771,1.938 0.375,0.167 10 false R-V 3.396,5.052 3.594,5.219 0.198,0.167 10 false U 3.396,5.771 3.594,5.938 0.198,0.167 10 false V 3.385,6.5 3.583,6.667 0.198,0.167 10 false W 5.823,3.552 6.198,3.719 0.375,0.167 10 false VOL- 5.792,3.969 6.167,4.135 0.375,0.167 10 false DRN 5.823,5.052 6.26,5.219 0.438,0.167 10 false VOL+ 5.792,5.479 6.167,5.646 0.375,0.167 10 false DRN 3.375,2.438 3.75,2.604 0.375,0.167 10 false R-W 4.052,3.583 4.469,3.74 0.417,0.156 10 false ACPE 4.052,5.052 4.469,5.208 0.417,0.156 10 false ACPB 1.667,0.906 1.865,1.073 0.198,0.167 10 false 1 1.677,1.573 1.875,1.74 0.198,0.167 10 false 2 1.667,2.219 1.854,2.448 0.188,0.229 10 false 3 1.667,2.885 1.854,3.115 0.188,0.229 10 false 4 3.125,0.906 3.313,1.135 0.188,0.229 10 false 3 3.125,1.573 3.323,1.74 0.198,0.167 10 false 2 3.104,4.844 3.292,5.073 0.188,0.229 10 false 1 3.104,5.563 3.302,5.729 0.198,0.167 10 false 2 3.094,2.219 3.292,2.417 0.198,0.198 10 false 1 3.115,6.292 3.313,6.49 0.198,0.198 10 false 3 4.604,3.354 4.792,3.583 0.188,0.229 10 false 1 5.604,3.396 5.792,3.625 0.188,0.229 10 false 1 4.615,4.854 4.813,5.021 0.198,0.167 10 false 2 5.604,4.885 5.802,5.052 0.198,0.167 10 false 2 2.052,4.875 2.24,5.104 0.188,0.229 10 false 1 2.052,5.625 2.25,5.792 0.198,0.167 10 false 2 2.052,6.354 2.25,6.552 0.198,0.198 10 false 3 2.438,8.385 3.354,8.583 0.917,0.198 10 false *: Shielded 2.51,4.813 2.656,5.031 0.146,0.219 10 false * 5.115,3.313 5.271,3.51 0.156,0.198 10 false * 5.115,4.813 5.26,5.031 0.146,0.219 10 false * 2.74,0.792 2.896,0.99 0.156,0.198 10 false * 1.063,0.969 1.26,1.135 0.198,0.167 10 false 3 1.052,1.594 1.25,1.76 0.198,0.167 10 false 2 1.052,2.26 1.24,2.49 0.188,0.229 10 false 1 1.042,2.969 1.229,3.198 0.188,0.229 10 false 4 2.365,0.906 2.552,1.135 0.188,0.229 10 false 1 2.385,1.563 2.583,1.729 0.198,0.167 10 false 2 2.375,2.24 2.573,2.406 0.198,0.167 10 false 3 1.573,3.469 3.865,3.667 2.292,0.198 10 false Connector Cover 3.385,3.083 4.333,3.313 0.948,0.229 10 false PCU_MOTOR

for RHD:
A479476E02
0.896,8.365 2.135,8.563 1.24,0.198 10 false : High Voltage Line 0.156,3.458 0.469,3.656 0.313,0.198 10 false q1 1.625,1.083 1.938,1.281 0.313,0.198 10 false q2 1.625,1.75 1.938,1.948 0.313,0.198 10 false q2 1.625,2.406 1.938,2.604 0.313,0.198 10 false q2 1.625,3.063 1.938,3.26 0.313,0.198 10 false q2 2.333,1.104 2.646,1.302 0.313,0.198 10 false O3 2.323,1.771 2.635,1.969 0.313,0.198 10 false O3 2.323,2.427 2.635,2.625 0.313,0.198 10 false O3 3.073,1.115 3.385,1.313 0.313,0.198 10 false O1 3.073,1.771 3.385,1.969 0.313,0.198 10 false O1 3.063,2.427 3.375,2.625 0.313,0.198 10 false O1 3.073,5.021 3.385,5.219 0.313,0.198 10 false o2 3.073,5.74 3.385,5.938 0.313,0.198 10 false o2 3.073,6.469 3.385,6.667 0.313,0.198 10 false o2 4.531,3.552 4.844,3.75 0.313,0.198 10 false A32 4.542,5.042 4.854,5.24 0.313,0.198 10 false A32 0.156,3.625 1.156,4.177 1,0.552 10 false FCV with Motor Transaxle Assembly 0.24,7.219 0.552,7.417 0.313,0.198 10 false o1 0.229,7.427 1.708,7.833 1.479,0.406 10 false FC Air Compressor with Motor Assembly 2.906,7.479 5.188,7.667 2.281,0.188 10 false Inverter with Converter Assembly 5.792,5.865 6.104,6.063 0.313,0.198 10 false O4 5.792,6.042 6.76,6.427 0.969,0.385 10 false Electric Heater Sub-assembly 0.813,1.125 1.01,1.292 0.198,0.167 10 false U 0.823,1.771 1.021,1.938 0.198,0.167 10 false V 0.802,2.406 1,2.573 0.198,0.167 10 false W 1.792,5.042 1.99,5.208 0.198,0.167 10 false U 1.802,5.771 2,5.938 0.198,0.167 10 false V 1.781,6.49 1.979,6.656 0.198,0.167 10 false W 3.396,1.125 3.771,1.292 0.375,0.167 10 false R-U 3.396,1.771 3.771,1.938 0.375,0.167 10 false R-V 3.396,5.052 3.594,5.219 0.198,0.167 10 false U 3.396,5.771 3.594,5.938 0.198,0.167 10 false V 3.385,6.5 3.583,6.667 0.198,0.167 10 false W 5.813,3.563 6.188,3.729 0.375,0.167 10 false VOL- 5.802,3.969 6.177,4.135 0.375,0.167 10 false DRN 5.823,5.063 6.26,5.229 0.438,0.167 10 false VOL+ 5.792,5.469 6.167,5.635 0.375,0.167 10 false DRN 3.375,2.438 3.75,2.604 0.375,0.167 10 false R-W 4.063,3.563 4.479,3.719 0.417,0.156 10 false ACPE 4.052,5.052 4.469,5.208 0.417,0.156 10 false ACPB 1.656,0.906 1.854,1.073 0.198,0.167 10 false 1 1.656,1.573 1.854,1.74 0.198,0.167 10 false 2 1.667,2.219 1.854,2.448 0.188,0.229 10 false 3 1.667,2.906 1.854,3.135 0.188,0.229 10 false 4 3.094,0.906 3.281,1.135 0.188,0.229 10 false 1 3.104,1.573 3.302,1.74 0.198,0.167 10 false 2 3.104,4.844 3.292,5.073 0.188,0.229 10 false 3 3.104,5.563 3.302,5.729 0.198,0.167 10 false 2 3.094,2.219 3.292,2.417 0.198,0.198 10 false 3 3.104,6.292 3.302,6.49 0.198,0.198 10 false 1 4.615,3.354 4.802,3.583 0.188,0.229 10 false 1 5.604,3.396 5.792,3.625 0.188,0.229 10 false 1 4.625,4.844 4.823,5.01 0.198,0.167 10 false 2 5.604,4.875 5.802,5.042 0.198,0.167 10 false 2 2.052,4.875 2.24,5.104 0.188,0.229 10 false 1 2.052,5.625 2.25,5.792 0.198,0.167 10 false 2 2.052,6.354 2.25,6.552 0.198,0.198 10 false 3 2.313,8.344 3.229,8.542 0.917,0.198 10 false *: Shielded 2.51,4.813 2.656,5.031 0.146,0.219 10 false * 5.115,3.313 5.271,3.51 0.156,0.198 10 false * 5.115,4.802 5.26,5.021 0.146,0.219 10 false * 2.74,0.792 2.896,0.99 0.156,0.198 10 false * 1.052,0.948 1.25,1.115 0.198,0.167 10 false 3 1.052,1.604 1.25,1.771 0.198,0.167 10 false 2 1.042,2.26 1.229,2.49 0.188,0.229 10 false 1 1.042,2.958 1.229,3.188 0.188,0.229 10 false 4 2.365,0.906 2.552,1.135 0.188,0.229 10 false 1 2.385,1.563 2.583,1.729 0.198,0.167 10 false 2 2.375,2.24 2.573,2.406 0.198,0.167 10 false 3 1.542,3.479 2.604,3.656 1.063,0.177 10 false Connector Cover 3.375,3.094 4.385,3.302 1.01,0.208 10 false PCU_MOTOR

SYSTEM DESCRIPTION

HINT:

If a decrease in insulation resistance cannot be confirmed using a megohmmeter, check "Short Wave Highest Value Level" in the Data List.


SHORT WAVE HIGHEST VALUE LEVEL


a.

"Short Wave Highest Value Level" shows a decrease in insulation resistance. When insulation resistance decreases, "Insulation Lower" will be displayed. However, even though the insulation resistance of the vehicle is normal, "Short Wave Highest Value Level" may decrease, so that "Not Judge" will be displayed for any of the following conditions.

·

Within approximately 10 minutes since the ignition switch was turned to ON.

·

When the system voltages ("Hybrid/EV Battery Voltage", "VL-Voltage before Boosting" and "VH-Voltage after Boosting") are changing.

·

During boosting. If the Data List item "Boost Ratio" is not 0% or within a few seconds of it becoming 0%. (The values of "Hybrid/EV Battery Voltage", "VL-Voltage before Boosting" and "VH-Voltage after Boosting" are about the same when not boosting.)

·

When "No" is displayed for any of the following Data List items:

- Short Wave Highest Value Availability just after MG Inv On/Off

- Short Wave Highest Value Availability just after A/C Inv On/Off

- Short Wave Highest Value Availability just after SMR On/Off



b.

When "Short Wave Highest Value Level" shows "Insulation Lower LV3", insulation resistance will be close to 0 Ω. In this case, damage to a high-voltage cable or hybrid component (high-voltage), or a short to body ground due to intrusion of foreign matter, such as metal particles, can be suspected.



RELATED FREEZE FRAME DATA


If problem symptoms cannot be reproduced and a malfunction still exists after replacing a part as instructed, checking the following freeze frame data can help determine a trouble area.


Items to be Checked Using Freeze Frame Data:
Freeze Frame Data Diagnostic Note
Short Wave Highest Value Level Indicates that the insulation resistance has decreased.
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid/EV Battery Voltage

·

Boost Ratio


During boosting (when "Boost Ratio" is not 0%), or when "VL-Voltage before Boosting", "VH-Voltage after Boosting" or "Hybrid/EV Battery Voltage" is varying, "Short Wave Highest Value Level" may decrease even though the insulation resistance is normal.
·

SMRP Status

·

SMRB Status

·

SMRG Status


When "SMRP Status", "SMRB Status" and "SMRG Status" are all OFF, the insulation malfunction detection circuit detects a decrease in insulation resistance in the EV supply battery area ((*d) in the wiring diagram).
Example:

When the ignition switch is turned to ON (not to ON (READY)), all 3 system main relays are off and it is suspected that the EV supply battery assembly is disconnected from the high voltage circuits. If "Short Wave Highest Value Level" decreases a few minutes after the ignition switch is turned to ON (not to ON (READY)), the EV supply battery assembly may have an insulation malfunction.


Drive Motor Inverter Shutdown Request When "Drive Motor Inverter Shutdown Request" is ON, the insulation malfunction detection circuit cannot detect a decrease in insulation resistance in the drive motor system AC (alternating current) section (drive motor side of (*e) in the wiring diagram).
The drive motor system AC (alternating current) section includes the drive motor in the FCV with motor transaxle assembly, drive motor cables and the AC (alternating current) section of the motor drive circuit in the inverter with converter assembly.
FC Air Compressor Gate Shutdown Request When "FC Air Compressor Gate Shutdown Request" is ON, the insulation malfunction detection circuit cannot detect a decrease in insulation resistance in the FC air compressor motor system AC (alternating current) section (FC air compressor motor side of (*d) in the wiring diagram).
The FC air compressor system AC (alternating current) section includes the motor in the FC air compressor with motor assembly, FC air compressor motor cables and the AC (alternating current) section of the compressor motor drive circuit in the inverter with converter assembly.
A/C Consumption Power When the air conditioning system is off (air conditioning system power consumption is 0 W), the insulation malfunction detection circuit cannot detect a decrease in insulation resistance in the compressor with motor assembly AC (alternating current) section ((*c) in the wiring diagram).
The compressor with motor assembly AC (alternating current) section ((*c) in the wiring diagram) includes the air conditioning motor, wiring between the air conditioning motor and air conditioning inverter, and the AC (alternating current) section of the air conditioning motor drive circuit in the air conditioning inverter.
With the vehicle stopped, turn on/off the air conditioning system and observe "Short Wave Highest Val" to use as a diagnosis reference.

HINT:
·

Reproducing the vehicle conditions the moment a DTC was stored according to the freeze frame data and results of the customer problem analysis helps ensure that the same DTC is stored again.

Driving Status
Item Diagnostic Note
Vehicle Speed -
Accelerator Position Sensor No.1 Voltage % -
Shift Position -
Master Cylinder Control Torque -

Operation Conditions
Item Diagnostic Note
Drive Motor Temperature If any liquid leaks into the ATF, insulation resistance may decrease only when the temperature is high.
The motor temperature is likely to increase if the motor speed is low and output torque is high such as when cruising uphill slowly or accelerating from a low speed.

·

Customer Problem Analysis

Ask the customer about the operating conditions and environment when the malfunction occurred.

Item Diagnostic Note
Driving Condition (acceleration, deceleration, turning, etc.) Changes in the insulation of the parts with insufficient insulation due to changes in G force or vibration is suspected.
Road Condition (unpaved, etc.)
Weather (rain, snow, etc.) Water intrusion is suspected
Washing the vehicle (Whether the malfunction occurred after washing the vehicle?)
Whether water was spilled on the rear seats or in the luggage compartment
Was the luggage compartment trim cover installed?




FC COOLING SYSTEM CONFIRMATION ITEM


a.

The FC cooling system may be the likely cause of DTCs P0AA649 and P1EED49. If these DTCs are output, check the following items.

Item Note
FC coolant refilling and replacement history Make sure that water, LLC or any coolant other than the specific coolant for the FC cooling system (Toyota genuine FC stack coolant) has never been added.
HINT:

Do not add or replace with water or any coolant other than the specific coolant, as the insulation resistance inside the FC stack assembly may decrease.


FC cooling water ion-exchanger element replacement history Make sure that the FC cooling water ion-exchanger element is not used beyond its design life.
HINT:
·

If it is used beyond its design life, the insulation resistance of the FC coolant will become insufficient, because the ion-exchange power decreases as the element is used over time.

·

When the life of the FC cooling water ion-exchanger element is near to the end, an alert message will be indicated on the multi-information display inside the combination meter to urge the user to replace it.



Whether the vehicle was left stationary for a long period of time Confirm the usage of the vehicle, and check whether the vehicle was left stationary for a long period of time.
HINT:
·

If the vehicle remains stationary for a long period, impurities in the FC coolant may increase, and these impurities will increase the electrical conductivity.

·

If insulation resistance is low immediately after the system is started, the electrical conductivity of the coolant may have increased because the vehicle had been left stationary for a long period of time. If this occurs, the system performs control to increase the amount of FC coolant flow to quickly restore the electrical conductivity to normal.

·

During the above control, the master warning light comes on and "FC System Periodic Check in Progress" is displayed on the multi-information display inside the combination meter. In addition, "FC System Periodic Check Completed" will be displayed on the multi-information display when the control completes.






CAUTION / NOTICE / HINT

CAUTION:
·
A361801

When troubleshooting DTC P0AA649, use either a tool wrapped with vinyl insulation tape or an insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)

·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery with insulating tape after removing it.

If the EV supply battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C32
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an EV supply battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the EV supply battery or the EV supply stack sub-assembly is disposed of improperly or abandoned.

Therefore, make sure to return EV supply battery and all EV supply stack sub-assemblies through an authorized collection agent.


·

Before returning the EV supply battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the EV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the EV supply battery and EV supply stack sub-assemblies.

·
A358020

After removing the EV supply battery or the EV supply stack sub-assembly, keep it away from water. Exposure to water may cause the EV supply battery or the EV supply stack sub-assembly to produce heat, resulting in a fire.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

When measuring insulation resistance using a megohmmeter, set the megohmmeter to 500 V.


PROCEDURE

1.CHECK DTC OUTPUT (EV, EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P0AA649, P1C7C49, P1C7D49, P1C7E49, P1C7F49, P1EEC49, P1EED49, P1EEE49 or P1EEF49 only is output, or DTCs except the ones in the table below are also output. A
Any hybrid control system DTCs in the table below are output B
Any hybrid battery system DTCs in the table below are output C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
Hybrid battery system P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P062F46 Hybrid/EV Battery Energy Control Module EEPROM Calibration / Parameter Memory Failure
Power Source Circuit Malfunction Hybrid control system P06881F ECM/PCM Power Relay Sense Circuit Intermittent
System malfunction Hybrid control system P1C9E9F Hybrid/EV System Reset Stuck Off

HINT:
·

P0AA649 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (EV)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
NOTICE:
·

DTC P1C7C49, P1C7D49, P1C7E49, P1C7F49, P1EEC49, P1EED49, P1EEE49 and P1EEF49 are not stored with P0AA649 at the same time. If a drop in insulation resistance is detected and DTC P0AA649 is output, wait for 1 minute with the ignition switch ON (READY), the shift state is in drive (D) and the air conditioning system on within the same trip, then turn the ignition switch off and wait for 2 minutes to determine the DTC (P1C7C49, P1C7D49, P1C7E49, P1C7F49, P1EEC49, P1EED49, P1EEE49 or P1EEF49).

·

If only DTC P0AA649 is output, perform the diagnostic procedure for DTC P0AA649 to inspect all of the high voltage circuits.

·

When any other DTC indicating parts which the insulation resistance dropped are output, perform the diagnostic procedure for each DTC.



Result:
Result Proceed to
Only P0AA649 is output A
P0AA649 and P1C7C49 are output B
P0AA649 and P1C7D49 are output C
P0AA649 and P1C7E49 are output D
P0AA649 and P1C7F49 are output E
P0AA649 and P1EEC49 are output F
P0AA649 and P1EED49 are output G
P0AA649 and P1EEE49 are output H
P0AA649 and P1EEF49 are output I



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK FC COOLING WATER ION EXCHANGER ELEMENT

B

82.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

C

5.CHECK EV SUPPLY BATTERY ASSEMBLY (HIGH VOLTAGE CABLE)

D

84.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY

E

85.CHECK HIGH VOLTAGE DIRECT CURRENT AREA

F

101.CHECK FC AIR COMPRESSOR AREA (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)

G

102.CHECK FC COOLING WATER ION EXCHANGER ELEMENT

H

111.CHECK HYDROGEN RECIRCULATION PUMP ASSEMBLY

I

114.CHECK FC COOLING WATER PUMP ASSEMBLY
3.CHECK FC COOLING WATER ION EXCHANGER ELEMENT
a.

Make sure that the FC cooling water ion-exchanger element is not used beyond its design life.

HINT:
·

If it is used beyond its design life, the insulation resistance of the FC coolant will become insufficient, because the ion-exchange power decreases as the element is used over time.

·

When the life of the FC cooling water ion-exchanger element is near to the end, an alert message "Ion Filter Maintenance Required Visit Your Dealer" will be indicated on the multi-information display inside the combination meter.



Result:
Result Proceed to
"Ion Filter Maintenance Required Visit Your Dealer" is not displayed in the multi-information display of the combination meter. A
"Ion Filter Maintenance Required Visit Your Dealer" is displayed in the multi-information display of the combination meter. B




A

4.READ VALUE USING GTS (SHORT WAVE HIGHEST VALUE LEVEL)

B

80.REPLACE FC COOLING WATER ION EXCHANGER ELEMENT
4.READ VALUE USING GTS (SHORT WAVE HIGHEST VALUE LEVEL)

Pre-procedure1

a.

None.


Procedure1

a.

Read the Data List.

Powertrain > EV > Data List
Tester Display
Short Wave Highest Value Level
50003 397 242

b.

After turning the ignition switch to ON, wait 1 minute or more and check "Short Wave Highest Value Level".

HINT:

Do not turn the ignitionr switch to ON (READY).


Result:
Result Proceed to
Short Wave Highest Value Level displays Insulation Lower LV2 or Insulation Lower LV3 A
Other than above B



Post-procedure1

a.

Turn the ignition switch off.



A

5.CHECK EV SUPPLY BATTERY ASSEMBLY (HIGH VOLTAGE CABLE)

B

22.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY (NO. 2 BATTERY PACK WIRE)
5.CHECK EV SUPPLY BATTERY ASSEMBLY (HIGH VOLTAGE CABLE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


HINT:

Make sure that no foreign matter or water has entered the EV supply battery.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



c.
C373311N02
0.833,0.042 1.271,0.333 0.438,0.292 0.063,1.25 0.5,1.542 0.438,0.292 0.906,0.115 1.208,0.281 0.302,0.167 10 true z14 0.167,1.323 0.427,1.5 0.26,0.177 10 true z15

Disconnect the z14 and z15 battery voltage sensor (for upper side) connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
C373310N06
0.385,0.458 0.802,0.75 0.417,0.292 0.49,0.531 0.74,0.708 0.25,0.177 10 true y2

Disconnect the y2 battery ECU assembly connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C387667C01
1.646,1.146 1.063,0.563 true 1.656,1.344 1.115,1.792 true 0.083,0.073 0.396,0.271 0.313,0.198 10 true *a 0.958,0.406 1.115,0.604 0.156,0.198 10 false 1 0.99,1.781 1.146,1.979 0.156,0.198 10 false 2
*a Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Ignition switch off 10 MΩ or higher
2 - Body ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR (for Upper Side))

NG

11.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY
6.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR (for Upper Side))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



c.
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

Disconnect the y1 battery voltage sensor (for upper side) connector.

CAUTION:

Before disconnecting the y1 battery voltage sensor (for Upper Side) connector, disconnect the z14 and z15 connectors.



d.
C373310N06
0.385,0.458 0.802,0.75 0.417,0.292 0.49,0.531 0.74,0.708 0.25,0.177 10 true y2

Disconnect the y2 battery ECU assembly connector.

NOTICE:
·

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

·

Before disconnecting the connector, check that it is not loose or disconnected.




Procedure1

a.
C374919C38
1.49,2.438 1.927,2.74 0.438,0.302 1.49,0.188 1.927,0.5 0.438,0.313 2.844,4.24 3.063,3.458 true 0.792,1.135 0.469,0.583 true 1.646,0.271 1.958,0.469 0.313,0.198 10 false y2 1.667,2.51 1.979,2.708 0.313,0.198 10 false y1 2.688,4.292 3.146,4.49 0.458,0.198 10 false GA0 0.302,0.396 0.76,0.594 0.458,0.198 10 false GA0 0.052,0.198 0.365,0.354 0.313,0.156 10 false *a 0.115,2.448 0.427,2.604 0.313,0.156 10 false *b
*a Rear view of wire harness and connector
(to Battery ECU Assembly)
*b Rear view of wire harness and connector
(to Battery Voltage Sensor (for Upper Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y2,y1)Location & Routing

Click Connector(y2)Body>No. 1 EV Battery Pack Wire>Battery ECU Assembly

Click Connector(y1)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Upper)

y2-17 (GA0) - y1-19 (GA0) Ignition switch off Below 1 Ω
y2-17 (GA0) or y1-19 (GA0) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the y2 battery ECU assembly connector.


b.
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

Reconnect the y1 battery voltage sensor (for upper side) connector.

CAUTION:

Before connecting the z14 and z15 battery voltage sensor (for Upper Side) connectors, connect the y1 connector.




OK

7.INSPECT BATTERY VOLTAGE SENSOR (for Upper Side)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.INSPECT BATTERY VOLTAGE SENSOR (for Upper Side)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

When checking the battery voltage sensor (for Upper Side) resistance, select a probe of appropriate thickness (approximately 0.5 mm) from the tester lead set, and perform the measurement.


Pre-procedure1

a.
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

Disconnect the y1 battery voltage sensor (for upper side) connector.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:

Before disconnecting the y1 battery voltage sensor (for Upper Side) connector, disconnect the z14 and z15 connectors.



Procedure1

a.
C374921C24
1.51,1.094 1.927,1.396 0.417,0.302 0.573,3.5 0.99,3.802 0.417,0.302 2.354,3.5 2.771,3.802 0.417,0.302 2.958,2.156 2.75,1.729 true 0.5,4.396 0.115,4.073 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.667,1.167 1.979,1.365 0.313,0.198 10 false y1 0.688,3.583 1.146,3.781 0.458,0.198 10 false z14 2.479,3.583 2.938,3.781 0.458,0.198 10 false z15 2.854,2.229 3.313,2.427 0.458,0.198 10 false GA0 0.604,4.396 1.063,4.594 0.458,0.198 10 false GA0
*a Component without harness connected
(Battery Voltage Sensor (for Upper Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y1,z14)Location & Routing

Click Connector(y1)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Upper)

Click Connector(z14)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

y1-19 (GA0) - z14-10 (GA0) Ignition switch off 5.88 to 6.12 kΩ
y1-19 (GA0) or z14-10 (GA0) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

Reconnect the y1 battery voltage sensor (for upper side) connector.

CAUTION:

Before connecting the z14 and z15 battery voltage sensor (for Upper Side) connectors, connect the y1 connector.




OK

8.REPLACE BATTERY ECU ASSEMBLY

NG

9.REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)
8.REPLACE BATTERY ECU ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

9.REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

11.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


HINT:

Make sure that no foreign matter or water has entered the EV supply battery assembly.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A478514N01
2.333,0.104 2.792,0.438 0.458,0.333 0.896,0.104 1.354,0.438 0.458,0.333 2.469,0.208 2.927,0.406 0.458,0.198 10 false z13 1.031,0.208 1.49,0.406 0.458,0.198 10 false z12

Disconnect the high voltage cable connector of the EV supply battery assembly from the No. 1 EV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

A478515C01
2.302,0.083 2.802,0.448 0.5,0.365 5.344,0.135 5.844,0.5 0.5,0.365 1.625,1.302 2.042,0.885 true 5.583,1.271 5.125,0.917 true 2.469,0.198 2.927,0.396 0.458,0.198 10 false z12 5.479,0.26 5.938,0.458 0.458,0.198 10 false z13 0.198,0.156 0.656,0.354 0.458,0.198 10 false *a 1.51,1.292 1.969,1.49 0.458,0.198 10 false - 5.667,1.281 6.125,1.479 0.458,0.198 10 false +
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z13,z12)Location & Routing

Click Connector(z13)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

Click Connector(z12)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z13-1 (+) - Body ground Ignition switch off 10 MΩ or higher
z12-1 (-) - Body ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

12.CHECK EV BATTERY TERMINAL BLOCK

NG

21.REPLACE NO.1 EV BATTERY JUNCTION BLOCK ASSEMBLY
12.CHECK EV BATTERY TERMINAL BLOCK
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371877

Disconnect the high voltage cable connector of the EV supply battery assembly from the EV battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C371878C12
2.313,0.156 2.729,0.51 0.417,0.354 0.594,0.156 1.01,0.51 0.417,0.354 0.427,1.573 0.865,1.031 true 2.875,1.521 2.479,1.031 true 2.427,0.26 2.729,0.406 0.302,0.146 10 false z18 0.354,1.552 0.667,1.698 0.313,0.146 10 false - 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.708,0.271 1.021,0.417 0.313,0.146 10 false z19 2.865,1.552 3.177,1.698 0.313,0.146 10 false +
*a Component without harness connected
(EV Battery Terminal Block)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
z18 (+) - Body ground Ignition switch off 10 MΩ or higher
z19 (-) - Body ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

13.INSPECT BATTERY VOLTAGE SENSOR (for Lower Side)

NG

20.REPLACE EV BATTERY TERMINAL BLOCK
13.INSPECT BATTERY VOLTAGE SENSOR (for Lower Side)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

When checking the battery voltage sensor (for Lower Side) resistance, select a probe of appropriate thickness (approximately 0.5 mm) from the tester lead set, and perform the measurement.


Pre-procedure1

a.
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

Disconnect the y3 battery voltage sensor (for lower side) connector.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:

Before disconnecting the y3 battery voltage sensor (for Lower Side) connector, disconnect the z16 and z17 connectors.



Procedure1

a.
C374921C25
1.51,1.094 1.896,1.385 0.385,0.292 0.583,3.5 0.969,3.792 0.385,0.292 2.385,3.5 2.771,3.792 0.385,0.292 2.958,2.156 2.75,1.729 true 0.5,4.396 0.125,4.073 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.656,1.167 1.969,1.365 0.313,0.198 10 false y3 0.688,3.583 1.146,3.781 0.458,0.198 10 false z16 2.479,3.583 2.938,3.781 0.458,0.198 10 false z17 2.854,2.229 3.313,2.427 0.458,0.198 10 false GA2 0.604,4.396 1.063,4.594 0.458,0.198 10 false GA2
*a Component without harness connected
(to Battery Voltage Sensor (for Lower Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y3,z16)Location & Routing

Click Connector(y3)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Lower)

Click Connector(z16)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

y3-19 (GA2) - z16-10 (GA2) Ignition switch off 5.88 to 6.12 kΩ
y3-19 (GA2) or z16-10 (GA2) - Body ground and other terminals Ignition switch off 10 kΩ or higher



b.
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

Reconnect the y3 battery voltage sensor (for lower side) connector.

CAUTION:

Before connecting the z16 and z17 battery voltage sensor (for Lower Side) connectors, connect the y3 connector.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

14.CHECK NO.2 EV SUPPLY STACK SUB-ASSEMBLY

NG

19.REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)
14.CHECK NO.2 EV SUPPLY STACK SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
C377850C05
1.479,0.271 1.885,0.563 0.406,0.292 1.74,1.385 2.125,1.823 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.594,0.354 2.052,0.552 0.458,0.198 10 false z19 2.167,1.781 2.323,1.979 0.156,0.198 10 false -
*a No. 2 HV Supply Stack Sub-assembly
(to EV Battery Terminal Block)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
z19 (-) - Body ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

15.CHECK EV SUPPLY BATTERY ASSEMBLY

NG

18.REPLACE NO.2 EV SUPPLY STACK SUB-ASSEMBLY
15.CHECK EV SUPPLY BATTERY ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that no electrolyte is leaking from each EV supply stack sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>INSPECTION


Result:
Result Proceed to
Electrolyte is not leaking from the EV supply stack sub-assembly. A
Electrolyte is leaking from the EV supply stack sub-assembly. B



A

16.REPLACE NO.1 EV SUPPLY STACK SUB-ASSEMBLY

B

17.REPLACE EV SUPPLY STACK SUB-ASSEMBLY (EV supply stack sub-assembly that has a leak of electrolyte)
16.REPLACE NO.1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

17.REPLACE EV SUPPLY STACK SUB-ASSEMBLY (EV supply stack sub-assembly that has a leak of electrolyte)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

18.REPLACE NO.2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

19.REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

20.REPLACE EV BATTERY TERMINAL BLOCK

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

21.REPLACE NO.1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

22.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY (NO. 2 BATTERY PACK WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371865C04
0.021,0.021 0.333,0.26 0.313,0.24 12 true *A 0.021,2.458 0.313,2.698 0.292,0.24 12 true *B
*A for LHD
*B for RHD


Remove the NO. 2 battery pack wire from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water has entered the inverter assembly with converter. Confirm that the inverter coolant volume has not increased.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

HINT:

As the insulation resistance may vary when drive motor rotates, perform this inspection while rotating the rear wheels.



d.

Move the shift lever to N and lift the vehicle.


Procedure1

a.
C371859C11
0.302,3.073 0.708,3.427 0.406,0.354 0.156,0.875 0.563,1.229 0.406,0.354 1.083,0.583 0.917,0.417 false 1.365,0.583 1.396,0.208 false 1.677,0.552 2.021,0.313 false 2.406,0.698 2.24,0.844 false 1.667,2.813 1.49,2.521 false 1.958,2.813 2.281,2.167 false 2.26,2.813 2.417,2.521 false 0.948,2.938 1.167,3.104 false 0.448,0.219 0.969,0.417 0.521,0.198 10 false 3 (R-U) 1.427,0.094 1.99,0.281 0.563,0.188 10 false 2 (R-V) 2.063,0.229 2.677,0.417 0.615,0.188 10 false 1 (R-W) 2.417,0.563 2.635,0.75 0.219,0.188 10 false *1 0.083,0.094 0.302,0.281 0.219,0.188 10 false *a 0.448,0.531 0.76,0.729 0.313,0.198 12 false *A 0.417,3.167 0.729,3.365 0.313,0.198 10 false O1 2.448,2.417 3.042,2.635 0.594,0.219 10 false 3 (R-W) 2.333,2.073 2.917,2.271 0.583,0.198 10 false 2 (R-V) 1,2.427 1.563,2.625 0.563,0.198 10 false 1 (R-U) 0.729,2.792 0.948,2.979 0.219,0.188 10 false *1 0.656,2.365 0.969,2.563 0.313,0.198 12 false *B 0.281,0.969 0.594,1.167 0.313,0.198 10 false O2
*A for LHD
*B for RHD
*1 Shield Ground
*a NO. 2 Battery Pack Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below while rotating the rear wheels 2 revolutions in the same direction simultaneously.

NOTICE:
·

Carefully perform this inspection as the drive motor may generate current when the front wheels are rotated by hand.

·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.



Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O2-3 (R-U) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher
O2-2 (R-V) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher
O2-1 (R-W) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O1-3 (R-W) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher
O1-2 (R-V) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher
O1-1 (R-U) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Lower the vehicle and push the P position switch.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

23.CHECK FC AIR COMPRESSOR AREA (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)

NG

77.CHECK NO. 2 BATTERY PACK WIRE
23.CHECK FC AIR COMPRESSOR AREA (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371868C04
0.021,0.021 0.354,0.24 0.333,0.219 12 true *A 0.021,2.458 0.333,2.688 0.313,0.229 12 true *B
*A for LHD
*B for RHD


Remove the FC air compressor motor cable assembly from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water has entered the inverter assembly with converter. Confirm that the inverter coolant volume has not increased.



Procedure1

a.
C371862C08
0.229,0.771 0.646,1.135 0.417,0.365 0.302,3.01 0.719,3.375 0.417,0.365 1.125,0.438 1.323,0.635 false 1.5,0.438 1.625,0.625 false 1.833,0.438 1.938,0.625 false 0.781,1.042 0.667,1.219 false 1.313,2.583 1.417,2.75 false 1.656,2.573 1.75,2.76 false 1.969,2.563 2.052,2.74 false 2.792,3.333 2.635,3.198 false 0.198,0.25 0.531,0.438 0.333,0.188 12 false *A 0.26,2.281 0.615,2.521 0.354,0.24 12 false *B 0.563,1.24 0.875,1.396 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.896,0.26 1.281,0.458 0.385,0.198 10 false 1 (U) 1.354,0.26 1.74,0.458 0.385,0.198 10 false 2 (V) 1.76,0.26 2.146,0.458 0.385,0.198 10 false 3 (W) 1.854,2.385 2.24,2.583 0.385,0.198 10 false 3 (U) 1.073,2.385 1.458,2.583 0.385,0.198 10 false 1 (W) 1.479,2.385 1.865,2.583 0.385,0.198 10 false 2 (V) 2.76,3.385 3.073,3.542 0.313,0.156 10 false *1 0.365,0.854 0.615,1.052 0.25,0.198 10 false o3 0.427,3.094 0.677,3.292 0.25,0.198 10 false o2
*A for LHD
*B for RHD
*1 Shield Ground
*a FC Air Compressor Motor Cable Assembly
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
fpr LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o3-1 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o3-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o3-3 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o2-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o2-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o2-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

24.CHECK ELECTRIC HEATER SUB-ASSEMBLY

NG

74.CHECK FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
24.CHECK ELECTRIC HEATER SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483163C01
0.031,0 0.344,0.198 0.313,0.198 10 true *A 0.031,2.479 0.344,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the front compartment main wire connector from inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered orcontaminated the front compartment main wire.



Procedure1

a.
A260188C72
0.635,1.198 1.031,1.49 0.396,0.292 1,1.76 1.531,1.531 true 2.396,1.729 1.917,1.531 true 2.344,0.896 2.115,0.938 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 0.719,1.271 1.031,1.427 0.313,0.156 10 false A32 0.635,1.698 1.125,1.927 0.49,0.229 10 false ACPE 2.438,1.698 2.927,1.927 0.49,0.229 10 false ACPB
*1 Shield Ground
*a Component without harness connected
(Electric Heater Sub-assembly)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A32)Location & Routing

Click Connector(A32)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A32-2 (ACPB) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher
A32-1 (ACPE) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

25.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

69.CHECK FRONT COMPARTMENT MAIN WIRE
25.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483165C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC junction cable from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



Procedure1

a.
A493916C01
1.208,0.844 1.313,0.844 1.313,0.844 1.438,1.146 true 1.094,3.323 1.198,3.323 1.198,3.323 1.323,3.625 true 0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.448 0.313,2.646 0.313,0.198 10 true *B 0.958,3.24 1.146,3.438 0.188,0.198 10 true *1 1.042,0.771 1.208,0.979 0.167,0.208 10 true *1
*A for LHD
*B for RHD
*1 High Voltage Terminal


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
High voltage terminal - Body ground Ignition switch off 1 MΩ or higher


HINT:

Perform this inspection with the FC junction cable and front compartment main wire disconnected from the inverter with converter assembly.



b.
A481495C04
1.417,0.188 1.938,0.573 0.521,0.385 1.25,1.719 1.479,1.25 true 2.135,1.729 1.885,1.271 true 0.969,0.729 1.198,0.844 true 1.083,1.76 1.604,1.979 0.521,0.219 10 true F-N 1.604,0.333 1.854,0.531 0.25,0.198 10 true z31 2.104,1.76 2.625,1.979 0.521,0.219 10 true F-VH 0.115,0.135 0.365,0.333 0.25,0.198 10 true *a 0.771,0.677 1.021,0.875 0.25,0.198 10 true *1
*1 Shield Ground
*a FC Converter Power Outlet Cable (Inverter with Converter Assembly)
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z31)Location & Routing

Click Connector(z31)Engine Compartment>other>Inverter with Converter Assembly , FC Converter Assembly

z31-1 (F-VH) - Body ground and shield ground Ignition switch off 10 MΩ or higher
z31-2 (F-N) - Body ground and shield ground Ignition switch off 10 MΩ or higher


HINT:

Visually check the FC converter power outlet cable. Any damage may cause an insulation resistance drop.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

26.CHECK FC JUNCTION CABLE

NG

68.REPLACE INVERTER WITH CONVERTER ASSEMBLY
26.CHECK FC JUNCTION CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
C257176C52
0.438,1.031 0.833,1.344 0.396,0.313 0.969,1.719 1.26,1.188 true 2.25,1.729 1.938,1.177 true 2.635,0.625 2.375,0.771 true 2.688,0.542 3,0.698 0.313,0.156 10 false *1 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.26,1.75 2.573,1.906 0.313,0.156 10 false N 0.927,1.75 1.24,1.906 0.313,0.156 10 false P 0.583,1.115 0.896,1.271 0.313,0.156 10 false x1
*1 Shield Ground
*a FC Junction Cable
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(x1)Location & Routing

Click Connector(x1)Engine Compartment>FC Junction Cable>Inverter with Converter Assembly

x1-1 (P) - Body ground and shield ground Ignition switch off 10 MΩ or higher
x1-2 (N) - Body ground and shield ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the FC junction cable for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

27.CHECK FC CONVERTER ASSEMBLY

NG

49.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
27.CHECK FC CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A479490C01
0.938,0.313 1.375,0.635 0.438,0.323 2.917,1.333 2.844,1.156 true 2.219,1.344 2.302,1.167 true 2.208,1.375 2.302,1 true 2.927,1.354 2.833,1 true 2.854,1.385 3.135,1.531 0.281,0.146 10 true F-N 2.063,1.385 2.438,1.563 0.375,0.177 10 true F-VH 0.125,0.042 0.333,0.229 0.208,0.188 10 true *a 1.052,0.396 1.313,0.573 0.26,0.177 10 true z31
*a Component without harness connected
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

When measuring the resistance, placing the measurement probe against the spring contacts of the terminals (on the rectangular hole side) will damage the spring contacts of the terminals and cause poor continuity. Therefore, place the measurement probe against the terminals from the square holes without spring contacts.

·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z31)Location & Routing

Click Connector(z31)Engine Compartment>other>Inverter with Converter Assembly , FC Converter Assembly

z31-1 (F-VH) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
z31-2 (F-N) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

28.CHECK FC COOLING WATER PUMP ASSEMBLY

NG

47.REPLACE FC CONVERTER ASSEMBLY
28.CHECK FC COOLING WATER PUMP ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483169C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A341477C09
0.438,0.969 0.875,1.292 0.438,0.323 2.375,1.667 1.99,1.208 true 1.74,1.698 1.719,1.219 true 1.104,1.667 1.448,1.219 true 2.833,0.469 1.865,0.885 true 2.396,1.729 2.552,1.927 0.156,0.198 10 false U 1.031,1.729 1.188,1.927 0.156,0.198 10 false W 1.708,1.729 1.865,1.927 0.156,0.198 10 false V 0.146,0.115 0.354,0.302 0.208,0.188 10 false *a 0.604,1.063 0.917,1.271 0.313,0.208 10 false b1 2.927,0.385 3.135,0.573 0.208,0.188 10 false *1
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Cooling Water Pump Inverter assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

29.CHECK FC COOLING WATER PUMP INVERTER ASSEMBLY

NG

41.CHECK FC COOLING WATER PUMP CABLE
29.CHECK FC COOLING WATER PUMP INVERTER ASSEMBLY

Pre-procedure1

a.

None.


Procedure1

a.
A484686C02
0.74,1.073 1.135,1.385 0.396,0.313 0.708,1.906 0.823,1.656 true 1.302,1.896 1.083,1.656 true 1,1.896 0.969,1.656 true 1.406,1.292 1.073,1.563 true 0.479,1.938 0.792,2.125 0.313,0.188 10 true 3 (U) 0.885,1.156 1.104,1.323 0.219,0.167 10 true b1 0.885,1.938 1.24,2.125 0.354,0.188 10 true 2 (V) 1.281,1.938 1.74,2.135 0.458,0.198 10 true 1 (W) 1.479,1.219 1.708,1.385 0.229,0.167 10 true *1 0.135,0.104 0.365,0.271 0.229,0.167 10 true *a
*1 Shield Ground
*a Component without harness connected
(FC Cooling Water Pumo Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

30.CHECK HYDROGEN RECIRCULATION PUMP ASSEMBLY

NG

115.REMOVE FC CONVERTER ASSEMBLY
30.CHECK HYDROGEN RECIRCULATION PUMP ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483171C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the hydrogen recirculation pump cable from the FC converter assembly.


Procedure1

a.
A481494C01
0.49,0.906 0.906,1.24 0.417,0.333 1.229,1.635 1.448,1.188 true 1.74,1.698 1.698,1.208 true 2.177,1.646 1.99,1.188 true 1.146,1.677 1.302,1.875 0.156,0.198 10 false U 1.688,1.729 1.844,1.927 0.156,0.198 10 false V 2.188,1.698 2.344,1.896 0.156,0.198 10 false W 0.188,0.167 0.417,0.375 0.229,0.208 10 false *a 0.615,1 1.01,1.24 0.396,0.24 10 false z30
*a Hydrogen Recirculation Pump Cable
(Hydrogen Recirculation Pump Inverter assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z30)Location & Routing

Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assembly

z30-1 (U) - Body ground Ignition switch off 50 MΩ or higher
z30-2 (V) - Body ground Ignition switch off 50 MΩ or higher
z30-3 (W) - Body ground Ignition switch off 50 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

31.CHECK FC HYDROGEN PUMP INVERTER ASSEMBLY

NG

48.REPLACE HYDROGEN RECIRCULATION PUMP ASSEMBLY
31.CHECK FC HYDROGEN PUMP INVERTER ASSEMBLY

Pre-procedure1

a.

None.


Procedure1

a.
A484685N02
2.375,0.927 2.771,1.24 0.396,0.313 2.292,1.854 2.438,1.542 true 2.875,1.844 2.698,1.542 true 2.594,1.833 2.563,1.542 true 2.073,1.865 2.479,2.063 0.406,0.198 10 true 3 (W) 2.458,1.01 2.719,1.188 0.26,0.177 10 true z30 2.479,1.865 2.865,2.052 0.385,0.188 10 true 2 (V) 2.833,1.865 3.219,2.063 0.385,0.198 10 true 1 (U)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z30)Location & Routing

Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assembly

z30-1 (U) - Body ground ignition switch off 10 MΩ or higher
z30-2 (V) - Body ground ignition switch off 10 MΩ or higher
z30-3 (W) - Body ground ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

32.CHECK FC COOLANT

NG

112.REMOVE FC CONVERTER ASSEMBLY
32.CHECK FC COOLANT
a.

Check FC coolant (Toyota genuine FC stack coolant) replacement history.

HINT:

Do not add or mix water or any coolant other than the specific coolant (Toyota genuine FC stack coolant), as the insulation resistance inside the FC stack assembly may decrease and cause DTC P0AA649 to be stored.


NOTICE:

If filling of water or any coolant other than the specific coolant is confirmed, replace the coolant following the procedure in the "Countermeasures when coolant (Toyota genuine FC stack coolant) passages are filled incorrectly" section.


HINT:

Click hereEngine / Hybrid System>COOLING>COOLANT>PRECAUTION



Result:
Result Proceed to
Coolant or water other than FC coolant (Toyota genuine FC stack coolant ) is not filled. A
Coolant or water other than FC coolant (Toyota genuine FC stack coolant ) is filled. B



A

33.ASK ABOUT VEHICLE CONDITION (VEHICLE IS LEFT UNUSED FOR A LONG PERIOD OF TIME)

B

43.REPLACE COOLANT (FC STACK COOLANT)
33.ASK ABOUT VEHICLE CONDITION (VEHICLE IS LEFT UNUSED FOR A LONG PERIOD OF TIME)
a.

Confirm the usage of the vehicle, and check whether the vehicle was left stationary for a long period of time.

HINT:
·

If the vehicle remains stationary for a long period, impurities in the FC coolant may increase, and these impurities will increase the electrical conductivity.

·

If insulation resistance is low immediately after the system is started, the electrical conductivity of the coolant may have increased because the vehicle had been left stationary for a long period of time. If this occurs, the system performs control to increase the amount of FC coolant flow to quickly restore the electrical conductivity to normal.

·

During the above control, the master warning light comes on, "FC System Check in Progress" is displayed on the multi-information display inside the combination meter, and the warning buzzer sounds. In addition, "FC System Check Completed" will be displayed on the multi-information display when the control completes.




Result:
Result Proceed to
The vehicle was left stationary for a long period of time. A
The vehicle was not left stationary for a long period of time. B



A

34.CLEAR DTC

B

43.REPLACE COOLANT (FC STACK COOLANT)
34.CLEAR DTC
HINT:

Perform the DTC clear procedure 2 times.


Pre-procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397

b.

Turn the ignition switch off and wait 10 minutes or more.


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

35.PERFORM CONFIRMATION AFTER REPAIR
35.PERFORM CONFIRMATION AFTER REPAIR

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Result:
Result Proceed to
P0AA649 is output A
P0AA649 is not output B



A

36.REMOVE FC CONVERTER ASSEMBLY

B

COMPLETED

36.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

37.INSPECT FOR COOLANT LEAK (FOR INVERTER)
37.INSPECT FOR COOLANT LEAK (FOR INVERTER)
a.

Check the FC stack assembly and FC converter assembly for any coolant (for inverter) leaks or traces of leaks

Result:
Result Proceed to
No coolant (for inverter) leaks A
Coolant (for inverter) leaks found (traces of leaks found) B


HINT:

If a coolant leak cannot be found although the inverter reserve tank coolant is below the Low level, there may be a leak inside the FC converter assembly. (If there is a leak inside the FC converter assembly, DTC P0AA649 may be output.)




A

38.CHECK FC CONVERTER ASSEMBLY

B

46.REPLACE FC CONVERTER WITH FC STACK ASSEMBLY
38.CHECK FC CONVERTER ASSEMBLY

Pre-procedure1

a.

Install the grounding wire, FCPC (SST) from the FC converter assembly.


SST
09891-78010  

b.

Install the 2 ground terminals to the FC converter assembly at the specified torque with the M6 bolts.

Specified Condition:

T=10 N*m (102 kgf*cm, 7 ft.*lbf)


A491119C02
1.333,0.573 2.823,0.646 true 2.26,2.406 5.875,2.552 true 4.563,2.271 5.854,2.542 true 1.104,0.521 1.323,0.688 0.219,0.167 10 false *a 1.417,0.094 1.563,0.302 0.146,0.208 10 false *1 5.948,2.469 6.167,2.635 0.219,0.167 10 false *b
*1 FC Converter Assembly - -
*a Grounding Wire, FCPC (SST) *b M6 Bolt



Procedure1

a.

Connect the bolt installation hole "P" on the front of the vehicle and bolt installation hole "N" on the rear of the vehicle, and bolt installation hole "P" on the front of the vehicle and the No. 6 busbar.

FC Converter Assembly Inspection Procedure:
A493917C02
4.594,5.719 4.115,4.865 true 1.469,1.25 2.292,1.677 true 5.208,1.708 6.167,1.292 true 1.427,4.625 1.906,5.156 true 5.448,4.708 6.24,4.083 true 1.083,5.406 1.563,5.938 true 0.188,0.146 0.5,0.344 0.313,0.198 10 false *1 5.042,1.646 5.198,1.844 0.156,0.198 10 false P 2.375,1.667 2.531,1.865 0.156,0.198 10 false N 1.958,5.146 2.115,5.344 0.156,0.198 10 false N 5.333,4.656 5.49,4.854 0.156,0.198 10 false P 5.385,0.302 6.594,0.51 1.208,0.208 10 false Front of Vehicle 0.896,0.25 2.031,0.469 1.135,0.219 10 false Rear of Vehicle 4.625,5.719 5.823,5.948 1.198,0.229 10 false NO. 6 Busbar 1.635,5.917 2.667,6.135 1.031,0.219 10 false Body Ground 0.104,4.417 0.344,4.635 0.24,0.219 10 false *a
*1 FC Converter Assembly - -
*a Megohmmeter set to 500 V - -



b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the tablebelow.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
Bolt installation hole "N" on the rear of vehicle - Body ground (FC converter assembly) Ignition switch off 2 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

39.INSPECT FC STACK ASSEMBLY

NG

44.REPLACE FC CONVERTER ASSEMBLY
39.INSPECT FC STACK ASSEMBLY

Pre-procedure1

a.

None


Procedure1

a.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

A491118C01
4.156,1.094 4.719,2.24 4.719,2.24 4.833,2.24 true 3.25,0.281 3.365,0.281 3.365,0.281 3.458,0.646 true 0.531,0.24 0.844,0.438 0.313,0.198 10 false *a 3.135,0.219 3.448,0.417 0.313,0.198 10 false A 4.885,2.167 5.198,2.365 0.313,0.198 10 false B
*a FC Stack Assembly - -


NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
A - Body ground Ignition switch off 10 MΩ or higher
B - Body ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

PERFORM CONFIRMATION AFTER REPLACING PARTS

NG

40.REPLACE FC STACK ASSEMBLY
40.REPLACE FC STACK ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

41.CHECK FC COOLING WATER PUMP CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A480831

Disconnect the FC cooling water pump cable from the FC cooling water pump assembly.


b.
A341477C09
0.438,0.969 0.875,1.292 0.438,0.323 2.375,1.667 1.99,1.208 true 1.74,1.698 1.719,1.219 true 1.104,1.667 1.448,1.219 true 2.833,0.469 1.865,0.885 true 2.396,1.729 2.552,1.927 0.156,0.198 10 false U 1.031,1.729 1.188,1.927 0.156,0.198 10 false W 1.708,1.729 1.865,1.927 0.156,0.198 10 false V 0.146,0.115 0.354,0.302 0.208,0.188 10 false *a 0.604,1.063 0.917,1.271 0.313,0.208 10 false b1 2.927,0.385 3.135,0.573 0.208,0.188 10 false *1
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Asembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

42.REPLACE FC COOLING WATER PUMP ASSEMBLY

NG

45.REPLACE FC COOLING WATER PUMP CABLE
42.REPLACE FC COOLING WATER PUMP ASSEMBLY
HINT:

Click hereEngine / Hybrid System>COOLING>WATER PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

43.REPLACE COOLANT (FC STACK COOLANT)
HINT:

Click hereEngine / Hybrid System>COOLING>COOLANT>PRECAUTION


NOTICE:

Replace the coolant and the FC cooling water ion-exchanger element following the procedure in the "Countermeasures when coolant (Toyota genuine FC stack coolant) passages are filled incorrectly" section.


Result:
Proceed to
NEXT



NEXT

44.REPLACE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

45.REPLACE FC COOLING WATER PUMP CABLE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

46.REPLACE FC CONVERTER WITH FC STACK ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

47.REPLACE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

48.REPLACE HYDROGEN RECIRCULATION PUMP ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

49.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


b.

Prepare the vehicle according to the table below for 3 minutes.

Item Condition
Blower speed HI
Temperature setting MAX COLD
A/C switch On


c.

Turn the ignition switch off and wait for 10 minutes or more.


CAUTION:

Be sure to wear insulated gloves and protective goggles


d.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



e.
A480850C01
0.896,0.24 1.281,0.531 0.385,0.292 0.729,1.323 0.833,1.323 0.833,1.323 0.979,0.979 true 1.521,1.333 1.396,1.333 1.396,1.333 1.229,0.979 true 1.031,0.323 1.344,0.521 0.313,0.198 10 false b3 0.615,1.26 0.927,1.458 0.313,0.198 10 false P 1.563,1.281 1.875,1.479 0.313,0.198 10 false N 0.25,0.427 0.563,0.625 0.313,0.198 10 false *a
*a Component without harness connected
(Compressor with Motor Assembly)


Disconnect the d3 compressor with motor assembly connector.


Procedure1

a.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b3)Location & Routing

Click Connector(b3)Engine Compartment>FC Cooling Water Pump Cable>Compressor with Motor Assembly

b3-1 (N) - Body ground and shield ground Always 2 MΩ or higher
b3-2 (P) - Body ground and shield ground Always 2 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

50.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NG

67.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY
50.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


HINT:

Make sure that no foreign matter or water has entered the HV battery.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A478504N01
1.375,0.073 1.75,0.333 0.375,0.26 1.865,0.073 2.24,0.333 0.375,0.26 2,0.135 2.313,0.333 0.313,0.198 10 false N1 1.5,0.146 1.813,0.344 0.313,0.198 10 false N2

Disconnect the N1 and N2 floor under wire connector of the EV supply battery from the No. 1 EV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

A480853C01
3.021,0.135 3.438,0.448 0.417,0.313 3.74,0.135 4.156,0.448 0.417,0.313 2.792,0.896 2.625,1.125 true 3.469,0.906 3.76,1.115 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 3.771,1.115 4.083,1.313 0.313,0.198 10 true CBI 3.167,0.229 3.479,0.427 0.313,0.198 10 false N2 3.885,0.229 4.198,0.427 0.313,0.198 10 false N1 2.417,1.146 2.729,1.344 0.313,0.198 10 true CEI
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N1,N2)Location & Routing

Click Connector(N1)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

Click Connector(N2)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

N1-1 (CBI) - Body ground Ignition switch off 10 MΩ or higher
N2-1 (CEI) - Body ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

51.CHECK FC COOLING WATER PUMP CABLE

NG

21.REPLACE NO.1 EV BATTERY JUNCTION BLOCK ASSEMBLY
51.CHECK FC COOLING WATER PUMP CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483175C01
0.01,0 0.323,0.198 0.313,0.198 10 true *A 0,2.365 0.313,2.563 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the b4 FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A481492C01
1.521,0.135 1.927,0.479 0.406,0.344 1.125,1.677 1.49,1.24 true 2.177,1.688 1.885,1.25 true 2.365,0.885 2.031,0.99 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.667,0.24 1.979,0.396 0.313,0.156 10 false b4 0.979,1.698 1.469,1.927 0.49,0.229 10 false N 2.208,1.708 2.698,1.938 0.49,0.229 10 false P
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b4)Location & Routing

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b4-1 (N) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher
b4-2 (P) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

52.CHECK FLOOR UNDER WIRE

NG

45.REPLACE FC COOLING WATER PUMP CABLE
52.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484669C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.479 0.313,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the floor under wire connectors from the FC converter assembly.


HINT:

Make sure that no foreign matter has entered or contaminated the floor under wire.


Procedure1

a.
A483126C05
1.479,0.125 1.917,0.448 0.438,0.323 1.083,1.708 1.573,1.125 true 2.292,1.74 1.813,1.146 true 2.313,0.531 2.052,0.729 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.323,1.74 2.635,1.896 0.313,0.156 10 false CBI 0.865,1.75 1.177,1.906 0.313,0.156 10 false CEI 1.625,0.219 1.938,0.375 0.313,0.156 10 false N3 2.354,0.385 2.667,0.542 0.313,0.156 10 false *1
*1 Shield Ground
*a Floor Under Wire
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CBI) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
N3-2 (CEI) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the floor under wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

53.CHECK FC JUNCTION CABLE

NG

64.REPLACE FLOOR UNDER WIRE
53.CHECK FC JUNCTION CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484671C01
0,2.438 0.313,2.635 0.313,0.198 10 true *B 0,0 0.313,0.198 0.313,0.198 10 true *A
*A for LHD
*B for RHD


Disconnect the FC junction cable connectors from the FC converter assembly.


HINT:

Make sure that no foreign matter has entered or contaminated the FC junction cable.


Procedure1

a.
A483126C03
1.479,0.125 1.917,0.448 0.438,0.323 1.083,1.708 1.573,1.125 true 2.292,1.74 1.813,1.146 true 2.052,0.74 2.281,0.531 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.313,1.75 2.625,1.906 0.313,0.156 10 false N 1,1.75 1.313,1.906 0.313,0.156 10 false P 1.625,0.219 1.938,0.375 0.313,0.156 10 false x2 2.313,0.417 2.625,0.573 0.313,0.156 10 false *1
*1 Shield Ground
*a FC Junction Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(x2)Location & Routing

Click Connector(x2)Engine Compartment>FC Junction Cable>FC Converter Assembly

x2-1 (P) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
x2-2 (N) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the FC junction cable for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

54.CHECK FC CONVERTER ASSEMBLY

NG

60.REPLACE FC JUNCTION CABLE
54.CHECK FC CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A485259C01
0.719,0.094 1.156,0.427 0.438,0.333 1.948,0.063 2.385,0.396 0.438,0.333 2.49,0.479 2.927,0.813 0.438,0.333 0.792,2.531 1.229,2.865 0.438,0.333 2.104,2.521 2.542,2.854 0.438,0.333 2.458,2.927 2.896,3.26 0.438,0.333 0.073,0.073 0.281,0.271 0.208,0.198 10 true *A 0.104,2.479 0.302,2.667 0.198,0.188 10 true *B 0.854,0.156 1.063,0.354 0.208,0.198 10 true b4 2.083,0.125 2.302,0.333 0.219,0.208 10 true N3 2.625,0.552 2.823,0.76 0.198,0.208 10 true x2 0.927,2.604 1.135,2.802 0.208,0.198 10 true b4 2.25,2.594 2.469,2.802 0.219,0.208 10 true N3 2.604,3 2.802,3.208 0.198,0.208 10 true x2
*A for LHD
*B for RHD


Disconnect the FC junction cable connectors, floor under wire and FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A484692C02
1.885,0.781 2.292,1.115 0.406,0.333 1.854,1.75 2.021,1.313 true 2.406,1.74 2.198,1.302 true 0.094,0.052 0.406,0.25 0.313,0.198 10 true *a 2.021,0.875 2.219,1.042 0.198,0.167 10 true N3 1.698,1.792 2.188,1.958 0.49,0.167 10 true CBI (+) 2.292,1.792 2.74,1.958 0.448,0.167 10 true CEI (-)
*a Component without harness connected
(FC Converter Assembly)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

If the polarity of the tester probes is wrong, the correct value cannot be measured.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CEI) (Negative (-) probe) - Body ground Ignition switch off 10 MΩ or higher
N3-2 (CBI) (Positive (+) probe) - Body ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

55.CHECK FC COOLING WATER PUMP INVERTER ASSEMBLY

NG

57.REMOVE FC CONVERTER ASSEMBLY
55.CHECK FC COOLING WATER PUMP INVERTER ASSEMBLY

Pre-procedure1

a.
A483169C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A484686C02
0.74,1.073 1.135,1.385 0.396,0.313 0.708,1.906 0.823,1.656 true 1.302,1.896 1.083,1.656 true 1,1.896 0.969,1.656 true 1.406,1.292 1.073,1.563 true 0.479,1.938 0.792,2.125 0.313,0.188 10 true 3 (U) 0.885,1.156 1.104,1.323 0.219,0.167 10 true b1 0.885,1.938 1.24,2.125 0.354,0.188 10 true 2 (V) 1.281,1.938 1.74,2.135 0.458,0.198 10 true 1 (W) 1.479,1.219 1.708,1.385 0.229,0.167 10 true *1 0.135,0.104 0.365,0.271 0.229,0.167 10 true *a
*1 Shield Ground
*a Component without harness connected
(FC Cooling Water Pumo Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

56.CHECK FC HYDROGEN PUMP INVERTER ASSEMBLY

NG

115.REMOVE FC CONVERTER ASSEMBLY
56.CHECK FC HYDROGEN PUMP INVERTER ASSEMBLY

Pre-procedure1

a.
A483171C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the hydrogen recirculation pump cable from the FC converter assembly.


Procedure1

a.
A484685E01
2.375,0.927 2.771,1.24 0.396,0.313 2.292,1.854 2.438,1.542 true 2.875,1.844 2.698,1.542 true 2.594,1.833 2.563,1.542 true 2.156,1.865 2.563,2.063 0.406,0.198 10 true 3(W) 2.458,1.01 2.719,1.188 0.26,0.177 10 true z30 2.51,1.865 2.833,2.052 0.323,0.188 10 true 2(V) 2.833,1.865 3.146,2.052 0.313,0.188 10 true 1(U)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z30)Location & Routing

Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assembly

z30-1 (U) - Body ground Ignition switch off 10 MΩ or higher
z30-2 (V) - Body ground Ignition switch off 10 MΩ or higher
z30-3 (W) - Body ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

4.READ VALUE USING GTS (SHORT WAVE HIGHEST VALUE LEVEL)

NG

112.REMOVE FC CONVERTER ASSEMBLY
57.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

58.CHECK FC INVERTER INPUT JUNCTION COVER
58.CHECK FC INVERTER INPUT JUNCTION COVER

Pre-procedure1

a.

Remove the FC inverter input junction cover from the FC converter assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY



Procedure1

a.

Measure the resistance according to the value(s) inthe table below.

A493910C01
3.719,1.135 4.135,1.5 0.417,0.365 3.51,2.292 3.844,1.76 true 4.271,2.281 3.979,1.75 true 0.271,0.177 0.583,0.375 0.313,0.198 10 false *a 4.125,2.302 4.625,2.5 0.5,0.198 10 true CEI (-) 3.26,2.302 3.781,2.469 0.521,0.167 10 true CBI (+) 3.854,1.26 4.063,1.427 0.208,0.167 10 true N3
*1 FC Inverter Input Junction Cover - -


CAUTION:

Do not use a megohmmeter.


HINT:

Perform an inspection with the FC inverter input terminal and air conditioning compressor cable still installed to FC converter input junction cover.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CEI) (Negative (-) probe) - N3-2 (CBI) (Positive (+) probe) Ignition switch off 10 MΩ or higher


NOTICE:

If the polarity of the tester probes is wrong, thecorrect value cannot be measured.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the front compartment main wire connector.



OK

59.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

NG

61.CHECK AIR CONDITIONING COMPRESSOR CABLE
59.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

60.REPLACE FC JUNCTION CABLE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

61.CHECK AIR CONDITIONING COMPRESSOR CABLE

Pre-procedure1

a.
A492128

Remove the air conditioning compressor cable from the FC inverter input junction cover.


b.
A492129

Remove the air conditioning compressor cable from the FC inverter input terminal.


Procedure1

a.
A492122C02
2.448,2.323 2.854,2.656 0.406,0.333 1.333,3.167 1.552,2.469 true 2.021,3.177 1.792,2.469 true 0.094,0.052 0.406,0.25 0.313,0.198 10 true *a 2.594,2.427 2.833,2.594 0.24,0.167 10 true b4 1.302,3.198 1.49,3.385 0.188,0.188 10 true N 2.01,3.208 2.167,3.375 0.156,0.167 10 true P
*a Air Conditioning Compressor Cable


Measure the resistance according to the value(s) inthe table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b4)Location & Routing

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b4-1 (N) - b4-2 (P) Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

62.REPLACE FC INVERTER INPUT TERMINAL

NG

65.REPLACE AIR CONDITIONING COMPRESSOR CABLE
62.REPLACE FC INVERTER INPUT TERMINAL

NEXT

63.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY
63.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

64.REPLACE FLOOR UNDER WIRE

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

65.REPLACE AIR CONDITIONING COMPRESSOR CABLE

NEXT

66.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY
66.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

67.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY
HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

68.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

69.CHECK FRONT COMPARTMENT MAIN WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484673C01
0.021,0 0.333,0.198 0.313,0.198 10 true *A 0,2.51 0.313,2.708 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the front compartment main wire connector from No. 1 battery pack wire.

HINT:

Make sure that no foreign matter has entered or contaminated the front compartment main wire connector.



Procedure1

a.
A260188C72
0.635,1.198 1.031,1.49 0.396,0.292 1,1.76 1.531,1.531 true 2.396,1.729 1.917,1.531 true 2.344,0.896 2.115,0.938 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 0.719,1.271 1.031,1.427 0.313,0.156 10 false A32 0.635,1.698 1.125,1.927 0.49,0.229 10 false ACPE 2.438,1.698 2.927,1.927 0.49,0.229 10 false ACPB
*1 Shield Ground
*a Front Compartment Main Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A32)Location & Routing

Click Connector(A32)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A32-2 (ACPB) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher
A32-1 (ACPE) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

70.CHECK NO. 1 BATTERY PACK WIRE

NG

73.REPLACE FRONT COMPARTMENT MAIN WIRE
70.CHECK NO. 1 BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483173C02
0.021,0 0.333,0.198 0.313,0.198 10 true *A 0,2.51 0.313,2.708 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the No. 1 battery pack wire from electric heater sub-assembly.


Procedure1

a.
C400224C03
0.281,0.885 0.698,1.229 0.417,0.344 1.031,1.771 1.5,1.188 true 2.5,1.76 2.031,1.167 true 1.938,1.375 1.771,1.76 1.771,1.76 1.625,1.375 true 0.417,0.99 0.729,1.188 0.313,0.198 10 false O4 0.896,1.823 1.354,2.021 0.458,0.198 10 false VOL- 2.51,1.854 2.969,2.052 0.458,0.198 10 false VOL+ 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.677,1.802 1.99,2 0.313,0.198 10 false *1
*1 Shield Ground
*a NO. 1 Battery Pack Wire
(Electric Heater Sub-assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Engine Compartment>EV Battery Pack Wire>Electric Heater Sub-Assembly

O4-1 (VOL-) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher
O4-2 (VOL+) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

71.REPLACE ELECTRIC HEATER SUB-ASSEMBLY

NG

72.REPLACE NO. 1 BATTERY PACK WIRE
71.REPLACE ELECTRIC HEATER SUB-ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

72.REPLACE NO. 1 BATTERY PACK WIRE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

73.REPLACE FRONT COMPARTMENT MAIN WIRE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

74.CHECK FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A480840

Remove the FC air compressor motor cable assembly from the FC air compressor with motor assembly.

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR COMPRESSOR>REMOVAL



Procedure1

a.
C371862C08
0.229,0.771 0.646,1.135 0.417,0.365 0.302,3.01 0.719,3.375 0.417,0.365 1.125,0.438 1.323,0.635 false 1.5,0.438 1.625,0.625 false 1.833,0.438 1.938,0.625 false 0.781,1.042 0.667,1.219 false 1.313,2.583 1.417,2.75 false 1.656,2.573 1.75,2.76 false 1.969,2.563 2.052,2.74 false 2.792,3.333 2.635,3.198 false 0.198,0.25 0.531,0.438 0.333,0.188 12 false *A 0.26,2.281 0.615,2.521 0.354,0.24 12 false *B 0.563,1.24 0.875,1.396 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.896,0.26 1.281,0.458 0.385,0.198 10 false 1 (U) 1.354,0.26 1.74,0.458 0.385,0.198 10 false 2 (V) 1.76,0.26 2.146,0.458 0.385,0.198 10 false 3 (W) 1.854,2.385 2.24,2.583 0.385,0.198 10 false 3 (U) 1.073,2.385 1.458,2.583 0.385,0.198 10 false 1 (W) 1.479,2.385 1.865,2.583 0.385,0.198 10 false 2 (V) 2.76,3.385 3.073,3.542 0.313,0.156 10 false *1 0.365,0.854 0.615,1.052 0.25,0.198 10 false o3 0.427,3.094 0.677,3.292 0.25,0.198 10 false o2
*A for LHD
*B for RHD
*1 Shield Ground
*a FC Air Compressor Motor Cable Assembly
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o3-1 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o3-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o3-3 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o2-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o2-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o2-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

75.REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

NG

76.REPLACE FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
75.REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY
HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR COMPRESSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

76.REPLACE FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

77.CHECK NO. 2 BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A480837

Disconnect the No. 2 battery pack wire from connector cover.

HINT:

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

a.
C371859C11
0.302,3.073 0.708,3.427 0.406,0.354 0.156,0.875 0.563,1.229 0.406,0.354 1.083,0.583 0.917,0.417 false 1.365,0.583 1.396,0.208 false 1.677,0.552 2.021,0.313 false 2.406,0.698 2.24,0.844 false 1.667,2.813 1.49,2.521 false 1.958,2.813 2.281,2.167 false 2.26,2.813 2.417,2.521 false 0.948,2.938 1.167,3.104 false 0.448,0.219 0.969,0.417 0.521,0.198 10 false 3 (R-U) 1.427,0.094 1.99,0.281 0.563,0.188 10 false 2 (R-V) 2.063,0.229 2.677,0.417 0.615,0.188 10 false 1 (R-W) 2.417,0.563 2.635,0.75 0.219,0.188 10 false *1 0.083,0.094 0.302,0.281 0.219,0.188 10 false *a 0.448,0.531 0.76,0.729 0.313,0.198 12 false *A 0.417,3.167 0.729,3.365 0.313,0.198 10 false O1 2.448,2.417 3.042,2.635 0.594,0.219 10 false 3 (R-W) 2.333,2.073 2.917,2.271 0.583,0.198 10 false 2 (R-V) 1,2.427 1.563,2.625 0.563,0.198 10 false 1 (R-U) 0.729,2.792 0.948,2.979 0.219,0.188 10 false *1 0.656,2.365 0.969,2.563 0.313,0.198 12 false *B 0.281,0.969 0.594,1.167 0.313,0.198 10 false O2
*A for LHD
*B for RHD
*1 Shield Ground
*a NO. 2 Battery Pack Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O2-3 (R-U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O2-2 (R-V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O2-1 (R-W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O1-1 (R-U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O1-2 (R-V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O1-3 (R-W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

78.CHECK MOTOR CABLE

NG

83.REPLACE NO. 2 BATTERY PACK WIRE
78.CHECK MOTOR CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A480836

Remove the motor cable from connector cover.

HINT:

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

a.
A481517C01
0.49,1.167 0.906,1.479 0.417,0.313 1.24,1.74 1.469,1.344 true 2.188,1.729 1.938,1.354 true 1.542,1.74 1.708,1.344 true 2.615,0.854 2.292,0.76 true 2.656,0.813 2.969,0.969 0.313,0.156 10 false *1 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.125,1.771 2.438,1.927 0.313,0.156 10 false 3(U) 1.365,1.771 1.677,1.927 0.313,0.156 10 false 2(V) 0.99,1.781 1.302,1.938 0.313,0.156 10 false 1(W) 0.635,1.24 0.979,1.458 0.344,0.219 11 false q1
*1 Shield Ground
*a Motor Cable
(FCV Transaxle With Motor Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q1)Location & Routing

Click Connector(q1)Body>Motor Cable>FCV Transaxle with Motor Assembly

q1-3 (U) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher
q1-2 (V) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher
q1-1 (W) - Body ground and shielded wire ground Ignition switch off 100 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

79.REPLACE FCV WITH MOTOR TRANSAXLE ASSEMBLY

NG

81.REPLACE MOTOR CABLE
79.REPLACE FCV WITH MOTOR TRANSAXLE ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

80.REPLACE FC COOLING WATER ION EXCHANGER ELEMENT
HINT:

Click hereEngine / Hybrid System>COOLING>ION EXCHANGER ELEMENT>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

81.REPLACE MOTOR CABLE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

82.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

83.REPLACE NO. 2 BATTERY PACK WIRE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

84.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371865C04
0.021,0.021 0.333,0.26 0.313,0.24 12 true *A 0.021,2.458 0.313,2.698 0.292,0.24 12 true *B
*A for LHD
*B for RHD


Remove the No. 2 battery pack wire from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water has entered the inverter assembly with converter. Confirm that the inverter coolant volume has not increased.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

HINT:

As the insulation resistance may vary when drive motor rotates, perform this inspection while rotating the rear wheels.



d.

Move the shift position to N and lift the vehicle.


Procedure1

a.
C371859C11
0.302,3.073 0.708,3.427 0.406,0.354 0.156,0.875 0.563,1.229 0.406,0.354 1.083,0.583 0.917,0.417 false 1.365,0.583 1.396,0.208 false 1.677,0.552 2.021,0.313 false 2.406,0.698 2.24,0.844 false 1.667,2.813 1.49,2.521 false 1.958,2.813 2.281,2.167 false 2.26,2.813 2.417,2.521 false 0.948,2.938 1.167,3.104 false 0.448,0.219 0.969,0.417 0.521,0.198 10 false 3 (R-U) 1.427,0.094 1.99,0.281 0.563,0.188 10 false 2 (R-V) 2.063,0.229 2.677,0.417 0.615,0.188 10 false 1 (R-W) 2.417,0.563 2.635,0.75 0.219,0.188 10 false *1 0.083,0.094 0.302,0.281 0.219,0.188 10 false *a 0.448,0.531 0.76,0.729 0.313,0.198 12 false *A 0.417,3.167 0.729,3.365 0.313,0.198 10 false O1 2.448,2.417 3.042,2.635 0.594,0.219 10 false 3 (R-W) 2.333,2.073 2.917,2.271 0.583,0.198 10 false 2 (R-V) 1,2.427 1.563,2.625 0.563,0.198 10 false 1 (R-U) 0.729,2.792 0.948,2.979 0.219,0.188 10 false *1 0.656,2.365 0.969,2.563 0.313,0.198 12 false *B 0.281,0.969 0.594,1.167 0.313,0.198 10 false O2
*A for LHD
*B for RHD
*1 Shield Ground
*a No.2 Battery Pack Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below while rotating the rear wheels 2 revolutions in the same direction simultaneously.

NOTICE:
·

Carefully perform this inspection as the drive motor may generate current when the front wheels are rotated by hand.

·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.



Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O2-3 (R-U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O2-2 (R-V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O2-1 (R-W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O1-1 (R-U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O1-2 (R-V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
O1-3 (R-W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher



Post-procedure1

a.

Lower the vehicle and push the P position switch.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

68.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

79.REPLACE FCV WITH MOTOR TRANSAXLE ASSEMBLY
85.CHECK HIGH VOLTAGE DIRECT CURRENT AREA
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484669C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.479 0.313,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the floor under wire connectors from the FC converter assembly.


HINT:

Make sure that no foreign matter has entered or contaminated the floor under wire.


Procedure1

a.
A483126C05
1.479,0.125 1.917,0.448 0.438,0.323 1.083,1.708 1.573,1.125 true 2.292,1.74 1.813,1.146 true 2.313,0.531 2.052,0.729 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.323,1.74 2.635,1.896 0.313,0.156 10 false CBI 0.865,1.75 1.177,1.906 0.313,0.156 10 false CEI 1.625,0.219 1.938,0.375 0.313,0.156 10 false N3 2.354,0.385 2.667,0.542 0.313,0.156 10 false *1
*1 Shield Ground
*a Floor Under Wire
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CBI) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
N3-2 (CEI) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the floor under wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

86.CHECK FC COOLING WATER PUMP CABLE

NG

98.CHECK FLOOR UNDER WIRE
86.CHECK FC COOLING WATER PUMP CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483175C01
0.01,0 0.323,0.198 0.313,0.198 10 true *A 0,2.365 0.313,2.563 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the b4 FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A481492C01
1.521,0.135 1.927,0.479 0.406,0.344 1.125,1.677 1.49,1.24 true 2.177,1.688 1.885,1.25 true 2.365,0.885 2.031,0.99 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.667,0.24 1.979,0.396 0.313,0.156 10 false b4 0.979,1.698 1.469,1.927 0.49,0.229 10 false N 2.208,1.708 2.698,1.938 0.49,0.229 10 false P
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b4)Location & Routing

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b4-1 (N) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher
b4-2 (P) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

87.CHECK FC COOLING WATER PUMP INVERTER ASSEMBLY

NG

95.CHECK FC COOLING WATER PUMP CABLE
87.CHECK FC COOLING WATER PUMP INVERTER ASSEMBLY

Pre-procedure1

a.
A483169C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A484686C02
0.74,1.073 1.135,1.385 0.396,0.313 0.708,1.906 0.823,1.656 true 1.302,1.896 1.083,1.656 true 1,1.896 0.969,1.656 true 1.406,1.292 1.073,1.563 true 0.479,1.938 0.792,2.125 0.313,0.188 10 true 3 (U) 0.885,1.156 1.104,1.323 0.219,0.167 10 true b1 0.885,1.938 1.24,2.125 0.354,0.188 10 true 2 (V) 1.281,1.938 1.74,2.135 0.458,0.198 10 true 1 (W) 1.479,1.219 1.708,1.385 0.229,0.167 10 true *1 0.135,0.104 0.365,0.271 0.229,0.167 10 true *a
*1 Shield Ground
*a Component without harness connected
(FC Cooling Water Pumo Inverter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

88.CHECK FC HYDROGEN PUMP INVERTER ASSEMBLY

NG

115.REMOVE FC CONVERTER ASSEMBLY
88.CHECK FC HYDROGEN PUMP INVERTER ASSEMBLY

Pre-procedure1

a.
A483171C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the hydrogen recirculation pump cable from the FC converter assembly.


Procedure1

a.
A484685N02
2.375,0.927 2.771,1.24 0.396,0.313 2.292,1.854 2.438,1.542 true 2.875,1.844 2.698,1.542 true 2.594,1.833 2.563,1.542 true 2.073,1.865 2.479,2.063 0.406,0.198 10 true 3 (W) 2.458,1.01 2.719,1.188 0.26,0.177 10 true z30 2.479,1.865 2.865,2.052 0.385,0.188 10 true 2 (V) 2.833,1.865 3.219,2.063 0.385,0.198 10 true 1 (U)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z30)Location & Routing

Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assembly

z30-1 (U) - Body ground Ignition switch off 10 MΩ or higher
z30-2 (V) - Body ground Ignition switch off 10 MΩ or higher
z30-3 (W) - Body ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

89.CHECK FC CONVERTER ASSEMBLY

NG

112.REMOVE FC CONVERTER ASSEMBLY
89.CHECK FC CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A479490C01
0.938,0.313 1.375,0.635 0.438,0.323 2.917,1.333 2.844,1.156 true 2.219,1.344 2.302,1.167 true 2.208,1.375 2.302,1 true 2.927,1.354 2.833,1 true 2.854,1.385 3.135,1.531 0.281,0.146 10 true F-N 2.063,1.385 2.438,1.563 0.375,0.177 10 true F-VH 0.125,0.042 0.333,0.229 0.208,0.188 10 true *a 1.052,0.396 1.313,0.573 0.26,0.177 10 true z31
*a Component without harness connected
(FC Converter Assembly)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

When measuring the resistance, placing the measurement probe against the spring contacts of the terminals (on the rectangular hole side) will damage the spring contacts of the terminals and cause poor continuity. Therefore, place the measurement probe against the terminals from the square holes without spring contacts.

·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z31)Location & Routing

Click Connector(z31)Engine Compartment>other>Inverter with Converter Assembly , FC Converter Assembly

z31-1 (F-VH) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
z31-2 (F-N) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

90.CHECK FC JUNCTION CABLE

NG

94.REPLACE FC CONVERTER ASSEMBLY
90.CHECK FC JUNCTION CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484671C01
0,2.438 0.313,2.635 0.313,0.198 10 true *B 0,0 0.313,0.198 0.313,0.198 10 true *A
*A for LHD
*B for RHD


Disconnect the FC junction cable connectors from the FC converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the FC junction cable.



c.
A483165C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC junction cable from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



Procedure1

a.
A483126C03
1.479,0.125 1.917,0.448 0.438,0.323 1.083,1.708 1.573,1.125 true 2.292,1.74 1.813,1.146 true 2.052,0.74 2.281,0.531 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.313,1.75 2.625,1.906 0.313,0.156 10 false N 1,1.75 1.313,1.906 0.313,0.156 10 false P 1.625,0.219 1.938,0.375 0.313,0.156 10 false x2 2.313,0.417 2.625,0.573 0.313,0.156 10 false *1
*1 Shield Ground
*a FC Junction Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(x2)Location & Routing

Click Connector(x2)Engine Compartment>FC Junction Cable>FC Converter Assembly

x2-1 (P) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
x2-2 (N) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the FC junction cable for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

91.CHECK ELECTRIC HEATER SUB-ASSEMBLY

NG

93.REPLACE FC JUNCTION CABLE
91.CHECK ELECTRIC HEATER SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483163C01
0.031,0 0.344,0.198 0.313,0.198 10 true *A 0.031,2.479 0.344,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the front compartment main wire connector from inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the front compartment main wire connector.



Procedure1

a.
A260188C72
0.635,1.198 1.031,1.49 0.396,0.292 1,1.76 1.531,1.531 true 2.396,1.729 1.917,1.531 true 2.344,0.896 2.115,0.938 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 0.719,1.271 1.031,1.427 0.313,0.156 10 false A32 0.635,1.698 1.125,1.927 0.49,0.229 10 false ACPE 2.438,1.698 2.927,1.927 0.49,0.229 10 false ACPB
*1 Shield Ground
*a Front Compartment Main Wire
(Inverter With Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A32)Location & Routing

Click Connector(A32)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A32-2 (ACPB) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher
A32-1 (ACPE) - Body ground and shielded wire ground Ignition switch off 3 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

92.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

69.CHECK FRONT COMPARTMENT MAIN WIRE
92.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

93.REPLACE FC JUNCTION CABLE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

94.REPLACE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

95.CHECK FC COOLING WATER PUMP CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A480830

Disconnect the b3 compressor with motor assembly from the FC cooling water pump cable.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL



Procedure1

a.
A481492C01
1.521,0.135 1.927,0.479 0.406,0.344 1.125,1.677 1.49,1.24 true 2.177,1.688 1.885,1.25 true 2.365,0.885 2.031,0.99 true 2.396,0.802 2.708,0.958 0.313,0.156 10 false *1 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.667,0.24 1.979,0.396 0.313,0.156 10 false b4 0.979,1.698 1.469,1.927 0.49,0.229 10 false N 2.208,1.708 2.698,1.938 0.49,0.229 10 false P
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b4)Location & Routing

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b4-1 (N) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b4-2 (P) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

96.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

NG

97.REPLACE FC COOLING WATER PUMP CABLE
96.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

97.REPLACE FC COOLING WATER PUMP CABLE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

98.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A478504N01
1.375,0.073 1.75,0.333 0.375,0.26 1.865,0.073 2.24,0.333 0.375,0.26 2,0.135 2.313,0.333 0.313,0.198 10 false N1 1.5,0.146 1.813,0.344 0.313,0.198 10 false N2

Disconnect the N1 and N2 floor under wire connector of the EV supply battery from the No. 1 EV battery junction block assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the floor under wire.



Procedure1

a.
A483126C05
1.479,0.125 1.917,0.448 0.438,0.323 1.083,1.708 1.573,1.125 true 2.292,1.74 1.813,1.146 true 2.313,0.531 2.052,0.729 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.323,1.74 2.635,1.896 0.313,0.156 10 false CBI 0.865,1.75 1.177,1.906 0.313,0.156 10 false CEI 1.625,0.219 1.938,0.375 0.313,0.156 10 false N3 2.354,0.385 2.667,0.542 0.313,0.156 10 false *1
*1 Shield Ground
*a Floor Under Wire
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

N3-1 (CBI) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
N3-2 (CEI) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the floor under wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

99.REPLACE NO.1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NG

100.REPLACE FLOOR UNDER WIRE
99.REPLACE NO.1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

100.REPLACE FLOOR UNDER WIRE

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

101.CHECK FC AIR COMPRESSOR AREA (FC AIR COMPRESSOR WITH MOTOR ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371868C04
0.021,0.021 0.354,0.24 0.333,0.219 12 true *A 0.021,2.458 0.333,2.688 0.313,0.229 12 true *B
*A for LHD
*B for RHD


Remove the FC air compressor motor cable from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water has entered the inverter assembly with converter. Confirm that the inverter coolant volume has not increased.



Procedure1

a.
C371862C08
0.229,0.771 0.646,1.135 0.417,0.365 0.302,3.01 0.719,3.375 0.417,0.365 1.125,0.438 1.323,0.635 false 1.5,0.438 1.625,0.625 false 1.833,0.438 1.938,0.625 false 0.781,1.042 0.667,1.219 false 1.313,2.583 1.417,2.75 false 1.656,2.573 1.75,2.76 false 1.969,2.563 2.052,2.74 false 2.792,3.333 2.635,3.198 false 0.198,0.25 0.531,0.438 0.333,0.188 12 false *A 0.26,2.281 0.615,2.521 0.354,0.24 12 false *B 0.563,1.24 0.875,1.396 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.896,0.26 1.281,0.458 0.385,0.198 10 false 1 (U) 1.354,0.26 1.74,0.458 0.385,0.198 10 false 2 (V) 1.76,0.26 2.146,0.458 0.385,0.198 10 false 3 (W) 1.854,2.385 2.24,2.583 0.385,0.198 10 false 3 (U) 1.073,2.385 1.458,2.583 0.385,0.198 10 false 1 (W) 1.479,2.385 1.865,2.583 0.385,0.198 10 false 2 (V) 2.76,3.385 3.073,3.542 0.313,0.156 10 false *1 0.365,0.854 0.615,1.052 0.25,0.198 10 false o3 0.427,3.094 0.677,3.292 0.25,0.198 10 false o2
*A for LHD
*B for RHD
*1 Shield Ground
*a FC Air Compressor Motor Cable Assembly
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o3)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o3-1 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o3-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o3-3 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(o2)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o2-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o2-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
o2-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

68.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

75.REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY
102.CHECK FC COOLING WATER ION EXCHANGER ELEMENT
a.

Make sure that the FC cooling water ion-exchanger element is not used beyond its design life.

HINT:
·

If it is used beyond its design life, the insulation resistance of the FC coolant will become insufficient, because the ion-exchange power decreases as the element is used over time.

·

When the life of the FC cooling water ion-exchanger element is near to the end, an alert message "Ion Filter Maintenance Required Visit Your Dealer" will be indicated on the multi-information display inside the combination meter.



Result:
Result Proceed to
"Ion Filter Maintenance Required Visit Your Dealer" is not displayed in the multi-information display of the combination meter. A
"Ion Filter Maintenance Required Visit Your Dealer" is displayed in the multi-information display of the combination meter. B




A

103.CHECK FC COOLANT

B

80.REPLACE FC COOLING WATER ION EXCHANGER ELEMENT
103.CHECK FC COOLANT
a.

Check FC coolant (Toyota genuine FC stack coolant) replacement history.

HINT:

Do not add or mix water or any coolant other than the specific coolant (Toyota genuine FC stack coolant), as the insulation resistance inside the FC stack assembly may decrease and cause DTC P1EED49 to be stored.



NOTICE:

If filling of water or any coolant other than the specific coolant is confirmed, replace the coolant following the procedure in the "Countermeasures when coolant (Toyota genuine FC stack coolant) passages are filled incorrectly" section.


HINT:

Click hereEngine / Hybrid System>COOLING>COOLANT>PRECAUTION


Result:
Result Proceed to
Coolant or water other than FC coolant (Toyota genuine FC stack coolant ) is not filled. A
Coolant or water other than FC coolant (Toyota genuine FC stack coolant ) is filled. B



A

104.ASK ABOUT VEHICLE CONDITION (VEHICLE IS LEFT UNUSED FOR A LONG PERIOD OF TIME)

B

43.REPLACE COOLANT (FC STACK COOLANT)
104.ASK ABOUT VEHICLE CONDITION (VEHICLE IS LEFT UNUSED FOR A LONG PERIOD OF TIME)
a.

Confirm the usage of the vehicle, and check whether the vehicle was left stationary for a long period of time.

HINT:
·

If the vehicle remains stationary for a long period, impurities in the FC coolant may increase, and these impurities will increase the electrical conductivity.

·

If insulation resistance is low immediately after the system is started, the electrical conductivity of the coolant may have increased because the vehicle had been left stationary for a long period of time. If this occurs, the system performs control to increase the amount of FC coolant flow to quickly restore the electrical conductivity to normal.

·

During the above control, the master warning light comes on, "FC System Check in Progress" is displayed on the multi-information display inside the combination meter, and the warning buzzer sounds. In addition, "FC System Check Completed" will be displayed on the multi-information display when the control completes.




Result:
Result Proceed to
The vehicle was left stationary for a long period of time. A
The vehicle was not left stationary for a long period of time. B



A

105.CLEAR DTC

B

110.CLEAR DTC
105.CLEAR DTC
HINT:

Perform the DTC clear procedure 2 times.


Pre-procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397

b.

Turn the ignition switch off and wait 10 minutes or more.


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait 10 minutes or more.



NEXT

106.PERFORM CONFIRMATION AFTER REPLACING PARTS
106.PERFORM CONFIRMATION AFTER REPLACING PARTS

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal wait for 90 seconds or more.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON (READY) with the push the P position switch and wait for 2 minutes or more.


d.

If "FC System Periodic Check in Progress" is displayed on the multi-information display inside the combination meter, wait until "FC System Periodic Check Completed" is displayed.

HINT:
·

Waiting for at least 8 minutes is required until "FC System Periodic Check Complete" is displayed. The waiting time will be longer if the temperature of the FC coolant is high, such as immediately after the vehicle had been driven.

·

If the ignition switch is turned to ON (READY) but "FC System Periodic Check in Progress" will not be displayed on the multi-information display inside the combination meter, proceed to B.




Procedure1

a.

Perform confirmation after completing repairs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Result:
Result Proceed to
P1EED49 is output A
P1EED49 is not output B



Post-procedure1

a.

None.



A

107.REPLACE COOLANT (FC STACK COOLANT)

B

COMPLETED

107.REPLACE COOLANT (FC STACK COOLANT)
HINT:

Click hereEngine / Hybrid System>COOLING>COOLANT>PRECAUTION


NOTICE:

Replace the coolant and the FC cooling water ion-exchanger element following the procedure in the "Countermeasures when coolant (Toyota genuine FC stack coolant) passages are filled incorrectly" section.


Result:
Proceed to
NEXT



NEXT

108.PERFORM CONFIRMATION AFTER REPLACING PARTS
108.PERFORM CONFIRMATION AFTER REPLACING PARTS

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Result:
Result Proceed to
P1EED49 is output A
P1EED49 is not output B



A

109.REPLACE FC CONVERTER WITH FC STACK ASSEMBLY

B

COMPLETED

109.REPLACE FC CONVERTER WITH FC STACK ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK FRAME>REMOVAL


Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

110.CLEAR DTC
HINT:

Perform the DTC clear procedure 2 times.


Pre-procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397

b.

Turn the ignition switch off and wait 10 minutes or more.


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait 10 minutes or more.



NEXT

108.PERFORM CONFIRMATION AFTER REPLACING PARTS
111.CHECK HYDROGEN RECIRCULATION PUMP ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483171C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the hydrogen recirculation pump cable from the FC converter assembly.


Procedure1

a.
A481494C01
0.49,0.906 0.906,1.24 0.417,0.333 1.229,1.635 1.448,1.188 true 1.74,1.698 1.698,1.208 true 2.177,1.646 1.99,1.188 true 1.146,1.677 1.302,1.875 0.156,0.198 10 false U 1.688,1.729 1.844,1.927 0.156,0.198 10 false V 2.188,1.698 2.344,1.896 0.156,0.198 10 false W 0.188,0.167 0.417,0.375 0.229,0.208 10 false *a 0.615,1 1.01,1.24 0.396,0.24 10 false z30
*a Hydrogen Recirculation Pump Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z30)Location & Routing

Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assembly

z30-1 (U) - Body ground Ignition switch off 50 MΩ or higher
z30-2 (V) - Body ground Ignition switch off 50 MΩ or higher
z30-3 (W) - Body ground Ignition switch off 50 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

112.REMOVE FC CONVERTER ASSEMBLY

NG

48.REPLACE HYDROGEN RECIRCULATION PUMP ASSEMBLY
112.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

113.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY
113.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

114.CHECK FC COOLING WATER PUMP ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483169C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.469 0.313,2.667 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A341477C09
0.438,0.969 0.875,1.292 0.438,0.323 2.375,1.667 1.99,1.208 true 1.74,1.698 1.719,1.219 true 1.104,1.667 1.448,1.219 true 2.833,0.469 1.865,0.885 true 2.396,1.729 2.552,1.927 0.156,0.198 10 false U 1.031,1.729 1.188,1.927 0.156,0.198 10 false W 1.708,1.729 1.865,1.927 0.156,0.198 10 false V 0.146,0.115 0.354,0.302 0.208,0.188 10 false *a 0.604,1.063 0.917,1.271 0.313,0.208 10 false b1 2.927,0.385 3.135,0.573 0.208,0.188 10 false *1
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shielded wire ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

115.REMOVE FC CONVERTER ASSEMBLY

NG

42.REPLACE FC COOLING WATER PUMP ASSEMBLY
115.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

116.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY
116.REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY AND FC HYDROGEN PUMP INVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS