This DTC is stored when the telematics transceiver detects an open or a short in the telephone antenna (main) circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15CB11 | Telephone Main Antenna Circuit Short to Ground | Telephone antenna (main) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON. (Short circuit) | ·
Telephone antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Telematics transceiver |
Telematics | A |
| B15CB13 | Telephone Main Antenna Circuit Open | Telephone antenna (Main) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON. (Open circuit) | ·
Telephone antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Telematics transceiver |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for TOYOTA Connect).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Remove the telephone antenna assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Procedure1
| *a | Component without harness connected
(Telephone Antenna Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 4a | Always | 9 to 11 kΩ |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the antenna connector from the telephone antenna assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Procedure1
| *a | Front view of wire harness connector
(to Telephone Antenna Assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4 - B-3 | Always | Below 1 Ω |
| A-4a - B-3a | Always | Below 1 Ω |
| A-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the telematics transceiver.
Procedure1
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-3 - ANT1-[1] (TELM2) | Always | Below 1 Ω |
| B-3a - ANT1-[1a] | Always | Below 1 Ω |
| B-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for TOYOTA Connect)>REGISTRATION