The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.
The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.
Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
Devices using similar radio frequencies are used in the vehicle.
The ID of a tire pressure warning valve and transmitter is mistyped during registration.
A tire, wheel and/or transmitter from a different vehicle is installed.
When no transmitter ID is received from a tire pressure warning valve and transmitter for 20 minutes*1 (10 minutes*2) or more while the vehicle speed is more than 40 km/h (25 mph), or no transmitter ID is received from all of the tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2 or more, DTCs from C2121 to C2124 are stored.
DTCs C2121 to C2124 can only be cleared by using the GTS. DTCs C2181 to C2184 can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181 to C2184 are output only in test mode.
*1: for FMVSS138 Type
*2: for ECE-R64 Type and GB26149 Type
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C2121 | No Signal from Transmitter ID1 | Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
Any transmitter ID is not received from tire pressure warning valve and transmitters. ·
Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more. (b) When both conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more. |
·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
| C2122 | No Signal from Transmitter ID2 | Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
Any transmitter ID is not received from tire pressure warning valve and transmitters. ·
Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more. (b) When both conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more. |
·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
| C2123 | No Signal from Transmitter ID3 | Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
Any transmitter ID is not received from tire pressure warning valve and transmitters. ·
Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more. (b) When both conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more. |
·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
| C2124 | No Signal from Transmitter ID4 | Either of the following conditions (a) or (b) is met:
(a) When all conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
Any transmitter ID is not received from tire pressure warning valve and transmitters. ·
Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more. (b) When both conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more. |
·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
| C2181 | Transmitter ID1 not Received (Test Mode DTC) | Test mode procedure is performed. | ·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
| C2182 | Transmitter ID2 not Received (Test Mode DTC) | Test mode procedure is performed. | ·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
| C2183 | Transmitter ID3 not Received (Test Mode DTC) | Test mode procedure is performed. | ·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
| C2184 | Transmitter ID4 not Received (Test Mode DTC) | Test mode procedure is performed. | ·
Tire pressure warning valve and transmitter ·
Tire pressure warning ECU and receiver ·
Smart Access System with Push-button Start (for Entry Function) |
Tire Pressure Monitor | A |
*1: for FMVSS138 Type
*2: for ECE-R64 Type and GB26149 Type
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
|
*1: for FMVSS138 Type *2: for ECE-R64 Type and GB26149 Type |
||||
| Diagnosis Condition | Tire pressure warning valve and transmitter is not in stop mode. | ○ | ○ | ○ |
| Vehicle speed is more than 40 km/h (25 mph). | ○ | - | - | |
| No vehicle speed signal is received. | - | ○ | - | |
| Malfunction Status | Any transmitter ID is not received from tire pressure warning valve and transmitters. | ○ | ○ | - |
| No transmitter ID is received from tire pressure warning valve and transmitters. | - | - | ○ | |
| Detection Time | 20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
|
| Number of Trips | - | - | - | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
|
*1: for FMVSS138 Type *2: for ECE-R64 Type and GB26149 Type |
||||
| Diagnosis Condition | Tire pressure warning valve and transmitter is not in stop mode. | ○ | ○ | ○ |
| Vehicle speed is more than 40 km/h (25 mph). | ○ | - | - | |
| No vehicle speed signal is received. | - | ○ | - | |
| Malfunction Status | Any transmitter ID is not received from tire pressure warning valve and transmitters. | ○ | ○ | - |
| No transmitter ID is received from tire pressure warning valve and transmitters. | - | - | ○ | |
| Detection Time | 20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
|
| Number of Trips | - | - | - | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
|
*1: for FMVSS138 Type *2: for ECE-R64 Type and GB26149 Type |
||||
| Diagnosis Condition | Tire pressure warning valve and transmitter is not in stop mode. | ○ | ○ | ○ |
| Vehicle speed is more than 40 km/h (25 mph). | ○ | - | - | |
| No vehicle speed signal is received. | - | ○ | - | |
| Malfunction Status | Any transmitter ID is not received from tire pressure warning valve and transmitters. | ○ | ○ | - |
| No transmitter ID is received from tire pressure warning valve and transmitters. | - | - | ○ | |
| Detection Time | 20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
|
| Number of Trips | - | - | - | |
DTC will be output when conditions for either of the patterns in the table above are met.
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
|
*1: for FMVSS138 Type *2: for ECE-R64 Type and GB26149 Type |
||||
| Diagnosis Condition | Tire pressure warning valve and transmitter is not in stop mode. | ○ | ○ | ○ |
| Vehicle speed is more than 40 km/h (25 mph). | ○ | - | - | |
| No vehicle speed signal is received. | - | ○ | - | |
| Malfunction Status | Any transmitter ID is not received from tire pressure warning valve and transmitters. | ○ | ○ | - |
| No transmitter ID is received from tire pressure warning valve and transmitters. | - | - | ○ | |
| Detection Time | 20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
20 minutes or more (*1)
10 minutes or more (*2) |
|
| Number of Trips | - | - | - | |
DTC will be output when conditions for either of the patterns in the table above are met.
When DTCs C2121 to C2124 are stored, DTC C2179 may be stored simultaneously. In such cases, troubleshoot DTCs C2121 to C2124 first, then troubleshoot DTC C2179.
If the GTS is used to display the ECU Data List for 10 minutes or more, DTCs C2121, C2122, C2123 and C2124 are stored to the tire pressure warning ECU.
If these DTCs are stored, clear the DTCs using the GTS.
If any of the DTCs from C2121 to C2124 is output, clear the DTCs or drive at 40 km/h (25 mph) for 1 minute or more.
It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.
When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.
It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.
| Result | Proceed to |
|---|---|
| excluding JPD20R-CEDSSW (w/ Panic Switch) | A |
| for JPD20R-CEDSSW (w/ Panic Switch) | B |
A
B
Check that the following conditions are not met:
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
for ECE-R64 Type and FMVSS138 Type:
If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.
for GB26149 Type:
If the vehicle is located in an area such as the one described above, the tire pressure warning light may blink due to interfering radio frequencies.
Devices using similar radio frequencies are used in the vehicle.
Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.
Radio transmissions may be interrupted due to the surroundings or devices installed by the user.
| Result | Proceed to |
|---|---|
| There is no device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. | A |
| There is a device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. | B |
A
B
Check the wireless door lock function using the electrical key transmitter sub-assembly switch.
| Result | Proceed to |
|---|---|
| Operates normally | A |
| Does not operate normally | B |
A
B
Check the stored DTC.
| Result | Proceed to |
|---|---|
| Any DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) | A |
| All DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) | B |
A
B
Pre-procedure1
Display the "ID Tire Position" value for each wheel using the GTS.
Procedure1
Refer to the following chart and check the wheel position of the DTC and transmitter match.
| Tester Display |
|---|
| ID 1 Tire Position |
| ID 2 Tire Position |
| ID 3 Tire Position |
| ID 4 Tire Position |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ID 1 Tire Position | ID1 Tire Position | No Information or FL or FR or RL or RR or Spare or Judging | ID1 tire position is displayed | If no tire position information is stored, "No Information" will be displayed. |
| ID 2 Tire Position | ID2 Tire Position | No Information or FL or FR or RL or RR or Spare or Judging | ID2 tire position is displayed | If no tire position information is stored, "No Information" will be displayed. |
| ID 3 Tire Position | ID3 Tire Position | No Information or FL or FR or RL or RR or Spare or Judging | ID3 tire position is displayed | If no tire position information is stored, "No Information" will be displayed. |
| ID 4 Tire Position | ID4 Tire Position | No Information or FL or FR or RL or RR or Spare or Judging | ID4 tire position is displayed | If no tire position information is stored, "No Information" will be displayed. |
Refer to the following chart for the Data List items that correspond to the DTCs.
| DTC No. | Detection Item | Data List |
|---|---|---|
| C2121 | No Signal from Transmitter ID1 | ID1 Tire Position |
| C2181 | Transmitter ID 1 not Received (for Test Diagnosis) | |
| C2122 | No Signal from Transmitter ID2 | ID2 Tire Position |
| C2182 | Transmitter ID 2 not Received (for Test Diagnosis) | |
| C2123 | No Signal from Transmitter ID3 | ID3 Tire Position |
| C2183 | Transmitter ID 3 not Received (for Test Diagnosis) | |
| C2124 | No Signal from Transmitter ID4 | ID4 Tire Position |
| C2184 | Transmitter ID 4 not Received (for Test Diagnosis) |
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Refer to the following chart and record the tire pressure warning valve and transmitter ID of the output DTC.
| Tester Display |
|---|
| Registered ID 1 Code |
| Registered ID 2 Code |
| Registered ID 3 Code |
| Registered ID 4 Code |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Registered ID 1 Code | Registered ID1 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID1 displayed | - |
| Registered ID 2 Code | Registered ID2 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID2 displayed | - |
| Registered ID 3 Code | Registered ID3 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID3 displayed | - |
| Registered ID 4 Code | Registered ID4 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID4 displayed | - |
*: Displayed only when the ID No. is not registered.
The wheel position cannot be determined from ID1 through ID4 on the Data List.
Refer to the following chart for the Data List items that correspond to the DTCs.
| DTC No. | Detection Item | Data List |
|---|---|---|
| C2121 | No Signal from Transmitter ID1 | Registered ID 1 code |
| C2181 | Transmitter ID 1 not Received (for Test Diagnosis) | |
| C2122 | No Signal from Transmitter ID2 | Registered ID 2 code |
| C2182 | Transmitter ID 2 not Received (for Test Diagnosis) | |
| C2123 | No Signal from Transmitter ID3 | Registered ID 3 code |
| C2183 | Transmitter ID 3 not Received (for Test Diagnosis) | |
| C2124 | No Signal from Transmitter ID4 | Registered ID 4 code |
| C2184 | Transmitter ID 4 not Received (for Test Diagnosis) |
Disassemble the tire indicated in the output DTC and check the tire pressure warning valve and transmitter ID.
| *1 | Tire Pressure Warning Valve and Transmitter | - | - |
| *a | Transmitter ID (7-digit Number) | - | - |
Procedure1
Confirm that the ID number on the transmitter and recorded transmitter ID match.
| Result | Proceed to |
|---|---|
| Match | A |
| Do not match | B |
Post-procedure1
None
A
B
Perform a test mode inspection and perform a send data check (C2181, C2182, C2183, C2184).
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
Explain to the customer that there is a high possibility that a DTC was output due to temporary electrical wave interference.
NG
Pre-procedure1
Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.
| Tester Display |
|---|
| Registered ID 1 Code |
| Registered ID 2 Code |
| Registered ID 3 Code |
| Registered ID 4 Code |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Registered ID 1 Code | Registered ID1 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID1 displayed | - |
| Registered ID 2 Code | Registered ID2 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID2 displayed | - |
| Registered ID 3 Code | Registered ID3 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID3 displayed | - |
| Registered ID 4 Code | Registered ID4 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID4 displayed | - |
*: Displayed only when the ID No. is not registered.
The wheel position cannot be determined from ID1 through ID4 on the Data List.
Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.
| *1 | Tire Pressure Warning Valve and Transmitter | - | - |
| *a | Transmitter ID (7-digit Number) | - | - |
Procedure1
Confirm that the ID number on the transmitter and recorded transmitter ID match.
| Result | Proceed to |
|---|---|
| Match | A |
| Do not match | B |
Post-procedure1
None
A
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Luggage Compartment)>REMOVAL
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Explain to the customer that there is a high possibility that a device (located near or inside the vehicle) or facility using electrical waves of approximately the same frequency is causing electrical wave interference.
Perform ID registration for the tire pressure warning valve and receiver.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Set the tire pressure to the specified value.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Procedure1
Initialize the tire pressure warning system.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the following conditions are not met:
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
for ECE-R64 Type and FMVSS138 Type:
If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.
for GB26149 Type:
If the vehicle is located in an area such as the one described above, the tire pressure warning light may blink due to interfering radio frequencies.
Devices using similar radio frequencies are used in the vehicle.
Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.
Radio transmissions may be interrupted due to the surroundings or devices installed by the user.
| Result | Proceed to |
|---|---|
| There is no device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. | A |
| There is a device or facility that uses electrical waves of approximately the same frequency in the vicinity of the vehicle or inside the vehicle. | B |
A
B
Check the stored DTC.
| Result | Proceed to |
|---|---|
| Any DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) | A |
| All DTCs from C2121 to C2124 are output (C2181 to C2184 when in Test Mode) | B |
A
B
Perform a test mode inspection and perform a send data check (C2181, C2182, C2183, C2184).
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
Explain to the customer that there is a high possibility that a DTC was output due to temporary electrical wave interference.
NG
Pre-procedure1
Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.
| Tester Display |
|---|
| Registered ID 1 Code |
| Registered ID 2 Code |
| Registered ID 3 Code |
| Registered ID 4 Code |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Registered ID 1 Code | Registered ID1 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID1 displayed | - |
| Registered ID 2 Code | Registered ID2 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID2 displayed | - |
| Registered ID 3 Code | Registered ID3 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID3 displayed | - |
| Registered ID 4 Code | Registered ID4 code | min.: 0
max.: FFFFFFF* |
ID No. registered for transmitter ID4 displayed | - |
*: Displayed only when the ID No. is not registered.
The wheel position cannot be determined from ID1 through ID4 on the Data List.
Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.
| *1 | Tire Pressure Warning Valve and Transmitter | - | - |
| *a | Transmitter ID (7-digit Number) | - | - |
Procedure1
Confirm that the ID number on the transmitter and recorded transmitter ID match.
| Result | Proceed to |
|---|---|
| Match | A |
| Do not match | B |
Post-procedure1
None
A
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER (for Quarter Pillar)>REMOVAL
B