Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1CE611  AC Inverter Status Signal Circuit Short to Ground  P1CE615  AC Inverter Status Signal Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Refer to the description for DTC P1C0F96

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C0F96

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1CE611 AC Inverter Status Signal Circuit Short to Ground VAIN input voltage AD value is lower than the threshold.
(1 trip detection logic)
·

EV control ECU

·

Voltage inverter

·

Wire harness or connector


Master Warning:
Does not come on
EV A
P1CE615 AC Inverter Status Signal Circuit Short to Auxiliary Battery or Open VAIN input voltage AD value is higher than the threshold.
(1 trip detection logic)
·

EV control ECU

·

Voltage inverter

·

Wire harness or connector


Master Warning:
Does not come on
EV A

WIRING DIAGRAM

Refer to the wiring diagram for DTC P1C0F96.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C0F96

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK VOLTAGE INVERTER (CHECK VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479493E06
1.167,1.594 1.594,1.906 0.427,0.313 1.26,1.667 1.51,1.865 0.25,0.198 10 true J15

Disconnect the J15 voltage inverter connector.

HINT:

Click hereVehicle Interior>POWER OUTLETS (INT)>VOLTAGE INVERTER>REMOVAL


NOTICE:

If the J15 connector is disconnected with the auxiliary battery connected, P1CE615 may be detected. Therefore, check that the cable is disconnected from the negative (-) auxiliary battery terminal before starting the operation.



c.

Connect the cable to the negative (-) auxiliarybattery terminal.


d.

Turn the ignition switch to ON.


Procedure1

a.
A391203C18
1.49,0.094 1.927,0.396 0.438,0.302 1.24,1.156 0.875,1.417 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.542,1.365 1.156,1.563 0.615,0.198 10 false VAIN 1.604,0.177 1.948,0.323 0.344,0.146 10 false J15
*a Front view of wire harness connector
(to Voltage Inverter)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(J15)Location & Routing

Click Connector(J15)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Voltage Inverter

J15-1 (VAIN) - Body ground Ignition switch ON 4.5 to 5.5 V


NOTICE:

If the ignition switch is turned to ON with the voltage inverter connector disconnected, other DTCs will be stored. Therefore, clear the DTCs after checking.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the J15 voltage inverter connector.



OK

NG

2.CHECK HARNESS AND CONNECTOR (VOLTAGE INVERTER - EV CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (VOLTAGE INVERTER - EV CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479493E02
1.219,1.677 1.646,1.99 0.427,0.313 1.313,1.76 1.604,1.938 0.292,0.177 10 true J15

Disconnect the J15 voltage inverter connector.

HINT:

Click hereVehicle Interior>POWER OUTLETS (INT)>VOLTAGE INVERTER>REMOVAL


NOTICE:

If the J15 connector is disconnected with the auxiliary battery connected, P1CE615 may be detected. Therefore, check that the cable is disconnected from the negative (-) auxiliary battery terminal before starting the operation.



c.

Disconnect the A17 EV control ECU connector.


Procedure1

a.
A480865C02
1.479,0.188 1.885,0.5 0.406,0.313 2.052,2.042 2.458,2.354 0.406,0.313 1.729,1.875 1.521,1.229 true 1.302,1.219 0.969,1.823 true 1.844,4.313 2.292,3.75 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 0.115,1.917 0.427,2.073 0.313,0.156 10 false *b 1.677,1.906 1.99,2.063 0.313,0.156 10 false IND 0.677,1.875 1.063,2.042 0.385,0.167 10 false VAIN 1.583,0.281 1.896,0.438 0.313,0.156 10 false J15 1.573,4.354 1.948,4.552 0.375,0.198 10 false VAIN 2.156,2.135 2.469,2.292 0.313,0.156 10 false A17
*a Front view of wire harness connector
(to Voltage Inverter)
*b Front view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(J15,A17)Location & Routing

Click Connector(J15)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Voltage Inverter

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

J15-1 (VAIN) - A17-11 (VAIN) Ignition switch off Below 1 Ω
J15-1 (VAIN) and A17-11 (VAIN) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A17 EV control ECU connector.


b.

Reconnect the J15 voltage inverter connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR