| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | PRECAUTION | - | ( )
|
- | - |
| 2 | CAUTIONS FOR HIGH VOLTAGE SYSTEM COMPONENTS | - | ( )
|
- | - |
| 3 | SERVICE PLUG GRIP | G3834 | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 10 | LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY | 64701 | - | - | - |
| 11 | LUGGAGE COMPARTMENT TRIM COVER LH | 64715D | - | - | - |
| 12 | TOOL BOX | 75201A | - | - | - |
| 13 | FRONT LUGGAGE COMPARTMENT TRIM COVER | 64075B | - | - | - |
| 14 | REAR FLOOR FINISH PLATE | 58387 | - | - | - |
| 15 | LUGGAGE COMPARTMENT TRIM COVER INNER LH | 64722 | - | - | - |
| 16 | LUGGAGE COMPARTMENT TRIM COVER INNER RH | 64721 | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | VOLTAGE INVERTER | 8624A | ( )
|
- | - |
| 18 | VOLTAGE INVERTER BRACKET | 86247A | ( )
|
- | - |
| *1 | UPPER INVERTER COVER | *2 | NO. 2 LUGGAGE ROOM WIRE |
| *3 | SOCKET INVERTER WIRE | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during voltage inverter removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. | - |
G3834
3.REMOVE SERVICE PLUG GRIP
53292A
4.REMOVE UPPER RADIATOR SUPPORT SEAL
1A906
5.REMOVE FC STACK COVER SUB-ASSEMBLY
64701
10.REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY
64715D
11.REMOVE LUGGAGE COMPARTMENT TRIM COVER LH
75201A
12.REMOVE TOOL BOX
64075B
13.REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER
58387
14.REMOVE REAR FLOOR FINISH PLATE
64722
15.REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH
64721
16.REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER RH
8624A
17.REMOVE VOLTAGE INVERTER
|
|
| *1 | No. 2 Luggage Room Wire | *2 | Socket Inverter Wire |
| *a | Green Lock | - | - |
|
Bolt |
|
Connector |
|
High Voltage Connector |
|
Nut |
|
Release Direction | - | - |
Remove the 2 bolts.
Disconnect the 2 No. 2 luggage room wire connectors and detach the clamp.
Unlock the 2 high voltage connectors green lock as shown and disconnect the No. 2 luggage room wire high voltage connector and the socket inverter wire high voltage connector.
Disconnect the No. 2 luggage room wire connector.
Remove the 4 nuts and upper inverter cover from the voltage inverter bracket.
Detach the clamp and remove the No. 2 luggage room wire from the upper inverter cover.
Remove the 4 bolts and voltage inverter from the upper inverter cover.
86247A
18.REMOVE VOLTAGE INVERTER BRACKET
|
|