Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P31DB9E  AC Inverter Drive Signal Stuck On  


DTC SUMMARY

MALFUNCTION DESCRIPTION


A malfunction is detected where the EV control ECU cannot shut down the operation of the voltage inverter.

The cause of this malfunction may be one of the following:

Wire harness malfunction
·

Wire harness between the voltage inverter and EV control ECU


EV control ECU malfunction
·

EV control ECU internal malfunction


Voltage inverter malfunction
·

Voltage inverter internal malfunction



DESCRIPTION

The EV control ECU sends voltage inverter operation permission/prohibition signals (NOAC signals) to the voltage inverter.

Also, it performs a functional check of the voltage inverter gate shutdown and outputs a DTC if a malfunction is found in the voltage inverter gate shutdown function.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P31DB9E AC Inverter Drive Signal Stuck On Continuing inverter output is detected even though a gate shutdown command for the power supply inverter was output.
(1 trip detection logic)
·

EV control ECU

·

Voltage inverter

·

Wire harness or connector


Master Warning Light:
Does not come on
EV A

Related Data List
DTC No. Data List
P31DB9E
·

AC Inverter Shutdown Request

·

AC Inverter Switch Indicator Control Status

·

AC Inverter Operation Status

·

AC Inverter Output Voltage



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch to ON (READY), press the power outlet switch and wait for at least 30 seconds.

3.

Press the power outlet switch again and wait for at least 30 seconds.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A479466E01
2,0.74 2.458,0.938 0.458,0.198 10 false IND 1.885,2.323 2.344,2.521 0.458,0.198 10 false VAIN 1.844,1.521 2.302,1.719 0.458,0.198 10 false NOAC 4.99,1.469 5.448,1.667 0.458,0.198 10 false NOAC 5,2.313 5.458,2.51 0.458,0.198 10 false VAIN 5,0.74 5.458,0.938 0.458,0.198 10 false ACIM 2.333,0.74 2.792,0.938 0.458,0.198 10 false 2 2.313,2.333 2.771,2.531 0.458,0.198 10 false 1 4.656,2.198 5.115,2.396 0.458,0.198 10 false 11 4.656,1.406 5.115,1.604 0.458,0.198 10 false 12 2.313,1.531 2.771,1.729 0.458,0.198 10 false 10 4.656,0.604 5.115,0.802 0.458,0.198 10 false 27 5.938,0.365 6.396,0.563 0.458,0.198 10 false 5 V 0.917,3.188 1.375,3.385 0.458,0.198 10 false J15 0.906,3.365 2.219,3.594 1.313,0.229 10 false Voltage Inverter 5.229,3.281 6.313,3.469 1.083,0.188 10 false EV Control ECU 5.917,1.969 6.375,2.167 0.458,0.198 10 false 5 V 5.927,1.052 6.385,1.25 0.458,0.198 10 false 12 V 4.667,0.823 5.125,1.021 0.458,0.198 10 false A8 4.635,1.625 5.094,1.823 0.458,0.198 10 false A8 4.625,2.417 5.083,2.615 0.458,0.198 10 false A17

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P31DB9E only is output, or DTCs except the ones in the table below are also output. A
Any of the DTCs in the table below are output B


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P060B1C Sensor Power Supply "A" Circuit / Open Circuit Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
Power source circuit malfunction P06881F ECM/PCM Power Relay Sense Circuit Intermittent
Sensor and actuator circuit malfunction P1CE611 AC Inverter Status Signal Circuit Short to Ground
P1CE615 AC Inverter Status Signal Circuit Short to Auxiliary Battery or Open
System malfunction P31D99F AC Inverter Status Signal Stuck Off
P1C0F96 AC Inverter Signal Line Component Internal Failure

HINT:
·

P31DB9E may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK HARNESS AND CONNECTOR (IND, VAIN VOLTAGE)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK HARNESS AND CONNECTOR (IND, VAIN VOLTAGE)

OK

3.CHECK HARNESS AND CONNECTOR (NOAC VOLTAGE)

NG

4.CHECK HARNESS AND CONNECTOR (IND, VAIN VOLTAGE)
3.CHECK HARNESS AND CONNECTOR (NOAC VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479493E01
1.219,1.677 1.646,1.99 0.427,0.313 1.313,1.76 1.604,1.938 0.292,0.177 10 true J15

Disconnect the J15 voltage inverter connector.

NOTICE:

If the J15 connector is disconnected with the auxiliary battery connected, P1CE615 may be detected. Therefore, check that the cable is disconnected from the negative (-) auxiliary battery terminal before starting the operation.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON (IG).


Procedure1

a.
A391203C15
2.531,1.094 2.906,1.396 0.375,0.302 1.813,1.333 2.052,1.844 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 2.021,1.865 2.635,2.063 0.615,0.198 10 false NOAC 2.604,1.177 3.073,1.333 0.469,0.156 10 false J15
*a Front view of wire harness connector
(to Voltage Inverter)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(J15)Location & Routing

Click Connector(J15)Body>No. 1 Luggage Room Wire / No. 3 Luggage Room Wire>Voltage Inverter

J15-10 (NOAC) - Body ground Ignition switch ON Below 1 V


NOTICE:

If the ignition switch is turned to ON (IG) with the voltage inverter connector disconnected, other DTCs will be stored. Therefore, clear the DTCs after checking.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the J15 voltage inverter connector.



OK

NG

5.CHECK HARNESS AND CONNECTOR (NOAC VOLTAGE)
4.CHECK HARNESS AND CONNECTOR (IND, VAIN VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479493E01
1.219,1.677 1.646,1.99 0.427,0.313 1.313,1.76 1.604,1.938 0.292,0.177 10 true J15

Disconnect the J15 voltage inverter connector.

NOTICE:

If the J15 connector is disconnected with the auxiliary battery connected, P1CE615 may be detected. Therefore, check that the cable is disconnected from the negative (-) auxiliary battery terminal before starting the operation.



c.

Connect the cable from the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON (IG).


Procedure1

a.
A478491C38
1.979,0.802 2.375,1.156 0.396,0.354 2.604,0.802 3,1.156 0.396,0.354 2.24,1.76 1.958,2.479 true 2.99,1.896 2.823,2.458 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.073,0.917 2.375,1.083 0.302,0.167 10 false A17 1.833,2.51 2.333,2.677 0.5,0.167 10 false VAIN 2.688,2.521 3.073,2.688 0.385,0.167 10 false ACIM 2.698,0.906 3,1.073 0.302,0.167 10 false A8
*a Front view of wire harness connector
(to EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A8,A17)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-27 (ACIM) - Body ground Ignition switch ON 4 V or higher
A17-11 (VAIN) - Body ground Ignition switch ON 4 V or higher


NOTICE:

If the ignition switch is turned to ON with the voltage inverter connector disconnected, other DTCs will be stored. Therefore, clear the DTCs after checking.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the J15 voltage inverter connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

5.CHECK HARNESS AND CONNECTOR (NOAC VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479493E01
1.219,1.677 1.646,1.99 0.427,0.313 1.313,1.76 1.604,1.938 0.292,0.177 10 true J15

Disconnect the J15 voltage inverter connector.

NOTICE:

If the J15 connector is disconnected with the auxiliary battery connected, P1CE615 may be detected. Therefore, check that the cable is disconnected from the negative (-) auxiliary battery terminal before starting the operation.



c.

Connect the cable from the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON (IG).


Procedure1

a.
A478491C39
2.604,0.802 3,1.156 0.396,0.354 2.865,1.75 2.573,2.51 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.417,2.521 2.958,2.75 0.542,0.229 10 false NOAC 2.698,0.906 3,1.073 0.302,0.167 10 false A8
*a Rear view of wire harness connector
(to EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A8)Location & Routing

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A8-12 (NOAC) - Body ground Ignition switch ON Below 1 V


NOTICE:

If the ignition switch is turned to ON with the voltage inverter connector disconnected, other DTCs will be stored. Therefore, clear the DTCs after checking.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the J15 voltage inverter connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG