Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2021.08
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2424  Lost Communication with Headlight Leveling ECU LH  B2425  Lost Communication with Headlight Leveling ECU RH  


DESCRIPTION

The headlight ECU sub-assembly sends auto leveling control signals to the headlight leveling motor via LIN communication.

The headlight leveling motor operates according to the power supply and control signals from the headlight ECU sub-assembly and sends its operation status to the headlight ECU sub-assembly via LIN communication.

The headlight ECU sub-assembly sends AHS control signals to the light control LED ECU via LIN communication.

The light control LED ECU receives power and control signals from the headlight ECU sub-assembly, controls the additional LEDs and additional fans, and sends its operation status to the headlight ECU sub-assembly via LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B2424 Lost Communication with Headlight Leveling ECU LH
Detection condition:

Ignition switch ON


Malfunction status:

LIN communication is lost with headlight leveling motor LH


Malfunction duration:

10 seconds or more


·

Headlight housing sub-assembly LH

·

Headlight leveling motor LH

·

Headlight ECU sub-assembly LH


AFS A -
B2425 Lost Communication with Headlight Leveling ECU RH
Detection condition:

Ignition switch ON


Malfunction status:

LIN communication is lost with headlight leveling motor RH


Malfunction duration:

10 seconds or more


·

Harness or connector

·

Headlight housing sub-assembly RH

·

Headlight leveling motor LH

·

Headlight ECU sub-assembly RH

·

Headlight ECU sub-assembly LH


AFS A -

Output DTC Suspected Area (Malfunction Status)
B2424 B2425 B2440 B2441

○: DTC is output.

-: DTC is not output

○ ○ ○ ○ LIN circuit (short)
Headlight ECU sub-assembly LH (Internal malfunction)
○ - ○ - Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - ○ Headlight ECU sub-assembly RH (Internal malfunction)
○ - - - Headlight leveling motor LH power supply system abnormal
Headlight leveling motor LH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly LH to headlight leveling motor LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - - Headlight leveling motor RH power supply abnormal
Headlight leveling motor RH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly RH to headlight leveling motor RH)
Headlight ECU sub-assembly RH (Internal malfunction)
- - ○ - Light control LED ECU LH power supply system abnormal
Light control LED ECU LH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly LH to light control LED ECU LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- - - ○ Light control LED ECU RH power supply system abnormal
Light control LED ECU RH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly RH to light control LED ECU RH)
Headlight ECU sub-assembly RH (Internal malfunction)

WIRING DIAGRAM

E475691E04
0.188,5.813 2.635,6.01 2.448,0.198 10 false Light Control LED ECU LH 5.333,1.292 6.063,1.552 0.729,0.26 10 false LIN I/F 4.708,3.396 5.438,3.656 0.729,0.26 10 false IG 4.677,0.854 5.406,1.115 0.729,0.26 10 false IG 1.229,6.521 3.344,6.75 2.115,0.229 10 false Headlight Unit Assembly LH 2.406,5.813 3.542,6.396 1.135,0.583 10 false Headlight Housing Sub-assembly LH 0.719,7.469 3.313,7.656 2.594,0.188 10 false : LIN Communication Line 4,3.802 4.542,4.188 0.542,0.385 10 false C 4,4.406 4.542,4.792 0.542,0.385 10 false C 4,4.979 4.542,5.365 0.542,0.385 10 false C 4,1.76 4.542,2.146 0.542,0.385 10 false C 4.021,1.26 4.563,1.646 0.542,0.385 10 false B 0.188,2.74 2.635,2.938 2.448,0.198 10 false Headlight Leveling Motor LH 4.01,2.271 4.552,2.656 0.542,0.385 10 false B 3.979,2.042 4.521,2.427 0.542,0.385 10 false 17 3.979,1.542 4.521,1.927 0.542,0.385 10 false 13 5.813,1.625 6.542,1.885 0.729,0.26 10 false LINL 6.354,1.542 7.083,1.802 0.729,0.26 10 false 20 6.292,1.76 7.021,2.021 0.729,0.26 10 false A96 4.021,1.052 4.563,1.438 0.542,0.385 10 false 9 1.781,1.031 2.323,1.417 0.542,0.385 10 false 1 1.781,1.521 2.323,1.906 0.542,0.385 10 false 3 1.792,2.052 2.333,2.438 0.542,0.385 10 false 4 4.021,3.583 4.563,3.969 0.542,0.385 10 false 6 4.01,4.188 4.552,4.573 0.542,0.385 10 false 3 4,4.76 4.542,5.146 0.542,0.385 10 false 1 1.76,4.76 2.302,5.146 0.542,0.385 10 false 21 1.75,4.167 2.292,4.552 0.542,0.385 10 false 13 1.75,3.583 2.292,3.969 0.542,0.385 10 false 12 1.792,1.26 2.146,1.51 0.354,0.25 10 false J 1.781,1.74 2.135,1.99 0.354,0.25 10 false J 1.792,2.26 2.146,2.51 0.354,0.25 10 false J 1.792,4.385 2.146,4.635 0.354,0.25 10 false K 1.802,3.802 2.156,4.052 0.354,0.25 10 false K 1.792,4.979 2.146,5.229 0.354,0.25 10 false K 4.26,6.844 6.646,7.198 2.385,0.354 10 false Headlight ECU Sub-assembly LH

E475692E04
4.271,6.875 6.698,7.427 2.427,0.552 10 false Headlight ECU Sub-assembly RH 1.573,6.583 4,7.135 2.427,0.552 10 false Headlight Unit Assembly RH 0.208,5.823 2.635,6.375 2.427,0.552 10 false Light Control LED ECU RH 1.792,1.25 2.135,1.521 0.344,0.271 10 false J 6.292,1.771 6.927,2.021 0.635,0.25 10 false A97 6.365,1.542 7,1.792 0.635,0.25 10 false 20 5.177,0.865 5.813,1.115 0.635,0.25 10 false IG 5.813,1.615 6.448,1.865 0.635,0.25 10 false LINL 5.167,3.406 5.802,3.656 0.635,0.25 10 false IG 4.01,1.76 4.646,2.01 0.635,0.25 10 false C 0.198,2.698 2.625,3.25 2.427,0.552 10 false Headlight Leveling Motor RH 1.792,4.979 2.427,5.229 0.635,0.25 10 false K 4.01,4.417 4.646,4.667 0.635,0.25 10 false C 4,3.802 4.635,4.052 0.635,0.25 10 false C 4.01,4.979 4.646,5.229 0.635,0.25 10 false C 4.021,4.75 4.656,5 0.635,0.25 10 false 1 1.792,1.031 2.427,1.281 0.635,0.25 10 false 1 1.792,1.542 2.427,1.792 0.635,0.25 10 false 3 4.031,4.188 4.667,4.438 0.635,0.25 10 false 3 4.031,3.583 4.667,3.833 0.635,0.25 10 false 6 1.792,2.063 2.427,2.313 0.635,0.25 10 false 4 3.99,1.531 4.625,1.781 0.635,0.25 10 false 13 4.021,1.031 4.656,1.281 0.635,0.25 10 false 9 4.01,1.26 4.646,1.51 0.635,0.25 10 false B 4.01,2.271 4.646,2.521 0.635,0.25 10 false B 3.99,2.052 4.625,2.302 0.635,0.25 10 false 17 1.76,3.583 2.396,3.833 0.635,0.25 10 false 12 1.76,4.177 2.396,4.427 0.635,0.25 10 false 13 0.74,7.458 3.313,7.75 2.573,0.292 10 false : LIN Communication Line 1.76,4.75 2.396,5 0.635,0.25 10 false 21 1.792,1.76 2.135,2.031 0.344,0.271 10 false J 1.781,2.271 2.125,2.542 0.344,0.271 10 false J 1.781,4.417 2.417,4.667 0.635,0.25 10 false K 1.792,3.813 2.427,4.063 0.635,0.25 10 false K 2.438,5.823 3.563,6.448 1.125,0.625 10 false Headlight Housing Sub-assembly RH

CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2424, B2425, B2440 and B2441 are output B
B2424 and B2440 are output C
B2425 and B2441 are output D
B2424 is output E
B2425 is output F



Post-procedure1

a.

None



A

B

3.CHECK HEADLIGHT ASSEMBLY RH

C

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

D

18.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

E

20.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY LH

F

23.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY RH
3.CHECK HEADLIGHT ASSEMBLY RH

Pre-procedure1

a.

Disconnect the A97 headlight ECU sub-assembly RH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

4.CHECK HEADLIGHT ASSEMBLY RH
4.CHECK HEADLIGHT ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2425 and B2441 are output B



Post-procedure1

a.

None



A

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

B

12.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the A96 headlight ECU sub-assembly LH connector.


b.

Disconnect the A97 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A96,A97)Location & Routing

Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

Click Connector(A97)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly RH

A96-20 (LINL) or A97-20 (LINL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Reconnect the A96 headlight ECU sub-assembly LH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

7.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
7.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2424 and B2440 are output B



Post-procedure1

a.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

8.CHECK HEADLIGHT LEVELING MOTOR LH
8.CHECK HEADLIGHT LEVELING MOTOR LH

Pre-procedure1

a.

Disconnect the headlight leveling motor LH connector.


b.

Reconnect the except headlight leveling motor LH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

9.CHECK HEADLIGHT LEVELING MOTOR LH
9.CHECK HEADLIGHT LEVELING MOTOR LH

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2424 is output B



Post-procedure1

a.

None



A

10.CHECK LIGHT CONTROL LED ECU LH

B

REPLACE HEADLIGHT LEVELING MOTOR LH

10.CHECK LIGHT CONTROL LED ECU LH

Pre-procedure1

a.

Disconnect the light control LED ECU LH connector.


b.

Reconnect the except light control LED ECU LH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

11.CHECK LIGHT CONTROL LED ECU LH
11.CHECK LIGHT CONTROL LED ECU LH

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2440 is output B



Post-procedure1

a.

None



A

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY LH

B

REPLACE LIGHT CONTROL LED ECU LH

12.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight ECU sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Reconnect the A97 headlight ECU sub-assembly RH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

13.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
13.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2425 and B2441 are output B



Post-procedure1

a.

None



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

14.CHECK HEADLIGHT LEVELING MOTOR RH
14.CHECK HEADLIGHT LEVELING MOTOR RH

Pre-procedure1

a.

Disconnect the headlight leveling motor RH connector.


b.

Reconnect the except headlight leveling motor RH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

15.CHECK HEADLIGHT LEVELING MOTOR RH
15.CHECK HEADLIGHT LEVELING MOTOR RH

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2425 is output B



Post-procedure1

a.

None



A

16.CHECK LIGHT CONTROL LED ECU RH

B

REPLACE HEADLIGHT LEVELING MOTOR RH

16.CHECK LIGHT CONTROL LED ECU RH

Pre-procedure1

a.

Disconnect the light control LED ECU RH connector.


b.

Reconnect the except light control LED ECU RH connector.


Procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165
Result:
Proceed to
NEXT



Post-procedure1

a.

None



NEXT

17.CHECK LIGHT CONTROL LED ECU RH
17.CHECK LIGHT CONTROL LED ECU RH

Pre-procedure1

a.

Turn the ignition switch ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2441 is output B



Post-procedure1

a.

None



A

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY LH

B

REPLACE LIGHT CONTROL LED ECU RH

18.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - HEADLIGHT ECU SUB-ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the A96 headlight ECU sub-assembly LH connector.


b.

Disconnect the A97 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A96,A97)Location & Routing

Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

Click Connector(A97)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly RH

A96-20 (LINL) - A97-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

19.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.
E384719C42
1.427,0.219 1.927,0.438 0.5,0.219 1.448,2.563 1.948,2.781 0.5,0.219 2.677,4.25 2.51,4.25 2.51,4.25 2.125,3.75 true 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 0.125,2.385 0.438,2.542 0.313,0.156 10 false *b 1.583,2.583 1.896,2.74 0.313,0.156 10 false A96 1.615,0.24 1.927,0.396 0.313,0.156 10 false C 2.74,4.146 3.094,4.333 0.354,0.188 10 false LINL
*a Component with harness connected
(Headlight ECU Sub-assembly RH)
*b Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Remove the headlight ECU sub-assembly RH as a unit with the connectors still connected.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Disconnect the A96 headlight ECU sub-assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A96)Location & Routing

Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

C-13 - A96-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

20.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY LH

Pre-procedure1

a.

Remove the headlight housing sub-assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


E384723C01
1.281,0.74 1.698,0.979 0.417,0.24 3.542,0.688 3.958,0.927 0.417,0.24 5.729,0.729 6.146,0.969 0.417,0.24 0.26,0.271 0.573,0.427 0.313,0.156 10 false *a 5.052,0.323 5.365,0.479 0.313,0.156 10 false *b 1.417,0.771 1.729,0.927 0.313,0.156 10 false B 3.677,0.719 3.99,0.875 0.313,0.156 10 false C 5.885,0.771 6.198,0.927 0.313,0.156 10 false J 2.896,0.302 3.208,0.458 0.313,0.156 10 false *a
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
*b Component without harness connected
(Headlight Leveling Motor LH)



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 - J-1 Always Below 1 Ω
B-17 - J-4 Always Below 1 Ω
C-13 - J-3 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

21.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY LH

21.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.
E378482C03
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.667,0.438 1.979,0.594 0.313,0.156 10 false J
*a Component without harness connected
(Headlight Leveling Motor LH)


Disconnect the headlight leveling motor LH connector.


b.

Reconnect the except headlight leveling motor LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J-1 - J-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

22.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

22.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.
E384719C43
1.427,0.219 1.927,0.438 0.5,0.219 1.448,2.563 1.948,2.781 0.5,0.219 2.677,4.25 2.51,4.25 2.51,4.25 2.125,3.75 true 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 0.125,2.385 0.438,2.542 0.313,0.156 10 false *b 1.583,2.583 1.896,2.74 0.313,0.156 10 false A97 1.615,0.24 1.927,0.396 0.313,0.156 10 false C 2.74,4.146 3.094,4.333 0.354,0.188 10 false LINL
*a Component with harness connected
(Headlight ECU Sub-assembly LH)
*b Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)


Remove the headlight ECU sub-assembly LH as a unit with the connectors still connected.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Disconnect the A97 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A97)Location & Routing

Click Connector(A97)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly RH

C-13 - A97-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

23.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY RH

Pre-procedure1

a.

Remove the headlight housing sub-assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


E384723C01
1.281,0.74 1.698,0.979 0.417,0.24 3.542,0.688 3.958,0.927 0.417,0.24 5.729,0.729 6.146,0.969 0.417,0.24 0.26,0.271 0.573,0.427 0.313,0.156 10 false *a 5.052,0.323 5.365,0.479 0.313,0.156 10 false *b 1.417,0.771 1.729,0.927 0.313,0.156 10 false B 3.677,0.719 3.99,0.875 0.313,0.156 10 false C 5.885,0.771 6.198,0.927 0.313,0.156 10 false J 2.896,0.302 3.208,0.458 0.313,0.156 10 false *a
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
*b Component without harness connected
(Headlight Leveling Motor RH)



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 - J-1 Always Below 1 Ω
B-17 - J-4 Always Below 1 Ω
C-13 - J-3 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

24.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY RH

24.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.
E378482C03
1.458,0.417 1.938,0.635 0.479,0.219 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.667,0.438 1.979,0.594 0.313,0.156 10 false J
*a Component without harness connected
(Headlight Leveling Motor RH)


Disconnect the headlight leveling motor RH connector.


b.

Reconnect the except headlight leveling motor RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J-1 - J-4 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

25.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

25.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.
E384719C44
1.427,0.219 1.927,0.438 0.5,0.219 1.448,2.563 1.948,2.781 0.5,0.219 2.677,4.25 2.51,4.25 2.51,4.25 2.125,3.75 true 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 0.125,2.385 0.438,2.542 0.313,0.156 10 false *b 1.573,2.573 1.885,2.729 0.313,0.156 10 false A96 1.615,0.24 1.927,0.396 0.313,0.156 10 false C 2.74,4.146 3.094,4.333 0.354,0.188 10 false LINL
*a Component with harness connected
(Headlight ECU Sub-assembly RH)
*b Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Remove the headlight ECU sub-assembly RH as a unit with the connectors still connected.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Disconnect the A96 headlight ECU sub-assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A96)Location & Routing

Click Connector(A96)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

C-13 - A96-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE HEADLIGHT LEVELING MOTOR RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH