Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2021.08
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448416 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Clearance Light/Daytime Running Light Circuit  


DESCRIPTION

Clearance light function:

When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the headlight ECU sub-assembly and illuminates the clearance lights.


Daytime running light function:

When the operation conditions of the daytime running lights are met, the main body ECU (multiplex network body ECU) sends an illumination request signal to the headlight ECU sub-assembly and illuminates the daytime running lights.


WIRING DIAGRAM

E471210E01
0.313,1.031 3.521,1.229 3.208,0.198 10 false Daytime Running Light 0.646,1.938 3.854,2.135 3.208,0.198 10 false Clearance Light 2.813,0.833 2.969,1.031 0.156,0.198 10 false H 2.833,1.208 2.99,1.406 0.156,0.198 10 false H 2.844,1.74 3,1.938 0.156,0.198 10 false H 2.823,2.146 2.979,2.344 0.156,0.198 10 false H 3.542,0.833 3.698,1.031 0.156,0.198 10 false G 3.531,1.219 3.688,1.417 0.156,0.198 10 false G 3.531,1.76 3.688,1.958 0.156,0.198 10 false G 3.531,2.156 3.688,2.354 0.156,0.198 10 false G 4.771,1.875 4.927,2.073 0.156,0.198 10 false G 4.771,1.417 4.927,1.615 0.156,0.198 10 false G 4.781,0.948 4.938,1.146 0.156,0.198 10 false G 5.552,0.958 5.708,1.156 0.156,0.198 10 false B 5.552,1.417 5.708,1.615 0.156,0.198 10 false B 5.552,1.875 5.708,2.073 0.156,0.198 10 false B 3.906,1.438 7.115,1.635 3.208,0.198 10 false LED ECU 3.135,2.948 6.344,3.146 3.208,0.198 10 false Headlight Housing Sub-assembly 0.406,2.938 3.615,3.135 3.208,0.198 10 false Headlight Lens Sub-assembly 2.094,3.656 5.302,3.854 3.208,0.198 10 false Headlight Unit Assembly 5.74,3.958 7.01,4.625 1.271,0.667 10 false Headlight ECU Sub-assembly 5.521,0.76 5.771,1 0.25,0.24 10 false 10 5.521,1.219 5.771,1.458 0.25,0.24 10 false 16 5.552,1.677 5.802,1.917 0.25,0.24 10 false 1 4.792,0.76 5.042,1 0.25,0.24 10 false 2 4.792,1.208 5.042,1.448 0.25,0.24 10 false 3 4.781,1.677 5.031,1.917 0.25,0.24 10 false 1 3.552,0.635 3.802,0.875 0.25,0.24 10 false 4 3.542,1.031 3.792,1.271 0.25,0.24 10 false 5 3.552,1.563 3.802,1.802 0.25,0.24 10 false 6 3.563,1.948 3.813,2.188 0.25,0.24 10 false 7 2.844,1.958 3.094,2.198 0.25,0.24 10 false 7 2.844,1.563 3.094,1.802 0.25,0.24 10 false 6 2.833,1.031 3.083,1.271 0.25,0.24 10 false 5 2.823,0.625 3.073,0.865 0.25,0.24 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Before troubleshooting, make sure that the customize setting "DRL Function" is set to "ON".


PROCEDURE

1.CHECK LIGHTS
a.

Check the illumination of each clearance lights and daytime running lights.


Result:
Result Proceed to
LH side clearance light and daytime running light does not illuminate. A
RH side clearance light and daytime running light does not illuminate. B



A

2.PERFORM ACTIVE TEST USING GTS

B

5.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

w/ Adaptive High Beam System:

Body Electrical > AFS > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > AFS > Active Test
Tester Display
Clearance Light
50004 165 43
Body Electrical > AFS > Active Test
Tester Display
Daytime Running Light
50004 165 46

w/o Adaptive High Beam System:

Body Electrical > HL AutoLeveling > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Clearance Light
50004 361 4
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Daytime Running Light
50004 361 7
OK:

Clearance lights and daytime running lights illuminate.



Result:
Procced to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HEADLIGHT UNIT ASSEMBLY LH
3.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the clearance light and daytime running light operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK


Result:
Result Proceed to
LH side clearance light and daytime running light does not illuminate. A
RH side clearance light and daytime running light does not illuminate. B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

4.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY LH
4.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY LH
a.

Remove the headlight housing sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY

E459082C02
5.24,0.854 5.781,1.125 0.542,0.271 3.531,0.865 4.073,1.135 0.542,0.271 1.479,0.865 2.021,1.135 0.542,0.271 0.531,0.604 0.844,0.802 0.313,0.198 10 false *a 1.708,0.927 2.021,1.125 0.313,0.198 10 false B 3.771,0.938 4.083,1.135 0.313,0.198 10 false G 5.458,0.927 5.771,1.125 0.313,0.198 10 false H 2.927,0.604 3.24,0.802 0.313,0.198 10 false *b 4.813,0.573 5.125,0.771 0.313,0.198 10 false *c
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to LED ECU)
*c Component without harness connected
(to Headlight Lens Sub-assembly LH)
- -



b.

Remove the headlight lens sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 - G-2 Always Below 1 Ω
B-16 - G-3 Always Below 1 Ω
B-1 - G-1 Always Below 1 Ω
G-4 - H-4 Always Below 1 Ω
G-5 - H-5 Always Below 1 Ω
G-6 - H-6 Always Below 1 Ω
G-7 - H-7 Always Below 1 Ω



Result:
Procced to
OK
NG



OK

REPLACE HEADLIGHT LENS SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY LH

5.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

w/ Adaptive High Beam System:

Body Electrical > AFS (Sub) > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > AFS (Sub) > Active Test
Tester Display
Clearance Light
50004 413 2
Body Electrical > AFS (Sub) > Active Test
Tester Display
Daytime Running Light
50004 413 5

w/o Adaptive High Beam System:

Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Clearance Light Clearance lights OFF or ON -
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display
Clearance Light
50004 414 2
Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display
Daytime Running Light
50004 414 5
OK:

Clearance lights and daytime running lights illuminate.



Result:
Procced to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.CHECK HEADLIGHT UNIT ASSEMBLY RH
6.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors to them.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Check that the clearance light and daytime running light operate normally.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK


Result:
Result Proceed to
RH side clearance light and daytime running light does not illuminate. A
LH side clearance light and daytime running light does not illuminate. B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

7.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY RH
7.CHECK HEADLIGHT HOUSING SUB-ASSEMBLY RH
a.

Remove the headlight housing sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY

E459082C02
5.24,0.854 5.781,1.125 0.542,0.271 3.531,0.865 4.073,1.135 0.542,0.271 1.479,0.865 2.021,1.135 0.542,0.271 0.531,0.604 0.844,0.802 0.313,0.198 10 false *a 1.708,0.927 2.021,1.125 0.313,0.198 10 false B 3.771,0.938 4.083,1.135 0.313,0.198 10 false G 5.458,0.927 5.771,1.125 0.313,0.198 10 false H 2.927,0.604 3.24,0.802 0.313,0.198 10 false *b 4.813,0.573 5.125,0.771 0.313,0.198 10 false *c
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to LED ECU)
*c Component without harness connected
(to Headlight Lens Sub-assembly RH)
- -



b.

Remove the headlight lens sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 - G-2 Always Below 1 Ω
B-16 - G-3 Always Below 1 Ω
B-1 - G-1 Always Below 1 Ω
G-4 - H-4 Always Below 1 Ω
G-5 - H-5 Always Below 1 Ω
G-6 - H-6 Always Below 1 Ω
G-7 - H-7 Always Below 1 Ω



Result:
Procced to
OK
NG



OK

REPLACE HEADLIGHT LENS SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT HOUSING SUB-ASSEMBLY RH