The headlight ECU sub-assembly sends auto leveling control signals to the headlight leveling motor via LIN communication.
The headlight leveling motor operates according to the power supply and control signals from the headlight ECU sub-assembly and sends its operation status to the headlight ECU sub-assembly via LIN communication.
The headlight ECU sub-assembly sends AHS control signals to the light control LED ECU via LIN communication.
The light control LED ECU receives power and control signals from the headlight ECU sub-assembly, controls the additional LEDs and additional fans, and sends its operation status to the headlight ECU sub-assembly via LIN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B2440 | Lost Communication with AHS EDU LH Module | Detection condition:
Ignition switch ON Malfunction status:
LIN communication is lost with light control LED ECU LH Malfunction duration:
10 seconds or more |
·
Headlight housing sub-assembly LH ·
Light control LED ECU LH ·
Headlight ECU sub-assembly LH |
AFS | A |
| B2441 | Lost Communication with AHS EDU RH Module | Detection condition:
Ignition switch ON Malfunction status:
LIN communication is lost with light control LED ECU RH Malfunction duration:
10 seconds or more |
·
Harness or connector ·
Headlight housing sub-assembly RH ·
Light control LED ECU RH ·
Headlight ECU sub-assembly RH ·
Headlight ECU sub-assembly LH |
AFS | A |
| Output DTC | Suspected Area (Malfunction Status) | |||
|---|---|---|---|---|
| B2424 | B2425 | B2440 | B2441 | |
|
○: DTC is output. -: DTC is not output |
||||
| ○ | ○ | ○ | ○ | LIN circuit (short) |
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||
| ○ | - | ○ | - | Headlight ECU sub-assembly LH (Internal malfunction) |
| - | ○ | - | ○ | Headlight ECU sub-assembly RH (Internal malfunction) |
| ○ | - | - | - | Headlight leveling motor LH power supply system abnormal |
| Headlight leveling motor LH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly LH to headlight leveling motor LH) | ||||
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||
| - | ○ | - | - | Headlight leveling motor RH power supply abnormal |
| Headlight leveling motor RH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly RH to headlight leveling motor RH) | ||||
| Headlight ECU sub-assembly RH (Internal malfunction) | ||||
| - | - | ○ | - | Light control LED ECU LH power supply system abnormal |
| Light control LED ECU LH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly LH to light control LED ECU LH) | ||||
| Headlight ECU sub-assembly LH (Internal malfunction) | ||||
| - | - | - | ○ | Light control LED ECU RH power supply system abnormal |
| Light control LED ECU RH (Internal malfunction) | ||||
| Harness open circuit (Headlight ECU sub-assembly RH to light control LED ECU RH) | ||||
| Headlight ECU sub-assembly RH (Internal malfunction) | ||||
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>REGISTRATION
Pre-procedure1
Clear the DTCs.
Turn the ignition switch to ON and wait for at least 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B2424, B2425 B2440 and B2441 are not output | A |
| B2424, B2425, B2440 and B2441 are output | B |
| B2424 and B2440 are output | C |
| B2425 and B2441 are output | D |
| B2440 is output | E |
| B2441 is output | F |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
F
Pre-procedure1
Remove the light control LED ECU LH.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AHS ECU>REMOVAL
| *a | Component without harness connected
(Headlight ECU Sub-assembly LH) |
*b | Component without harness connected
(Light Control LED ECU LH) |
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-6 - K-12 | Always | Below 1 Ω |
| C-3 - K-13 | Always | Below 1 Ω |
| C-1 - K-21 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component without harness connected
(Light Control LED ECU LH) |
Disconnect the light control LED ECU LH connector.
Reconnect the except light control LED ECU LH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K-12 - K-21 | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component with harness connected
(Headlight ECU Sub-assembly LH) |
| *b | Front view of wire harness connector
(to Headlight ECU Sub-assembly RH) |
Remove the headlight ECU sub-assembly LH as a unit with the connectors still connected.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Disconnect the A97 headlight ECU sub-assembly RH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A97)Location & Routingewd_type=routing;type=c;code=A97 |
||
| C-3 - A97-20 (LINL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the light control LED ECU RH.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AHS ECU>REMOVAL
| *a | Component without harness connected
(Headlight ECU Sub-assembly RH) |
*b | Component without harness connected
(Headlight Leveling Motor RH) |
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-6 - K-12 | Always | Below 1 Ω |
| C-3 - K-13 | Always | Below 1 Ω |
| C-1 - K-21 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component without harness connected
(Light Control LED ECU RH) |
Disconnect the light control LED ECU RH connector.
Reconnect the except light control LED ECU RH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K-12 - K-21 | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component with harness connected
(Headlight ECU Sub-assembly RH) |
| *b | Front view of wire harness connector
(to Headlight ECU Sub-assembly LH) |
Remove the headlight ECU sub-assembly RH as a unit with the connectors still connected.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Disconnect the A96 headlight ECU sub-assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A96)Location & Routingewd_type=routing;type=c;code=A96 |
||
| C-3 - A96-20 (LINL) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG