Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D2F96  FC Coolant Pump Component Internal Failure  


DESCRIPTION

The cooling system of the FC system maintains the FC stack temperature at an optimum level for power generation. The FC cooling water pump assembly is used to feed the FC stack with water that is needed to absorb heat emitted by power generation, and is also used to circulate coolant in the cooling system.

If the actual FC cooling water pump speed has significantly deviated from the target pump speed, the EV control ECU will interpret it as a FC cooling water pump malfunction and store this DTC.

For the circuit diagram, refer to DTC P1D2F00.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D2F00

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D2F96 FC Coolant Pump Component Internal Failure Deviation between the measured and target FC cooling water pump speeds has continued at a level that exceeds the threshold. While the ignition switch is ON (READY), this malfunction detection is active all the time.
(1 trip detection logic)
·

FC cooling water pump assembly

·

FC cooling water pump inverter assembly

·

FC cooling water pump cable


Master Warning: Comes on EV B

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ ○ ○ ○ ○

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1D2F96
·

FC Coolant Pump Speed

·

Target FC Coolant Pump Speed

·

FC Coolant Pump Main Power Supply Status

·

FC Coolant Pump Output Status

·

FC Coolant Pump Load Status

·

FC Coolant Pump Over Temperature Status

·

Lost Communication with FC Coolant Pump

·

FC Coolant Pump CPU Abnormal



Related Active Test
DTC No. Active Test
P1D2F96 Control the FC Coolant Pump

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (w/ 1500W Type Voltage Inverter)


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

Forcing the SOC of the EV supply battery assembly to decrease by applying electrical loads such as turning on the air conditioning (HOT MAX, maximum airflow), or depressing the accelerator pedal with the shift state in park (P), the "FC Intermittent Operation" of the Data List is easily to enter OFF (power generation mode).


After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF. Then, wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1D2F96 is output A
P1D2F96 is output and DTCs other than the DTCs in the table below are output B
P1D2F96 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Communication system malfunction P1DC887 (EV) Lost Communication with FC Coolant Pump Inverter Missing Message
System malfunction P0A784B (Hybrid (EV) Control System) Drive Motor "A" Inverter Over Temperature
P0A789E (Hybrid (EV) Control System) Drive Motor "A" Inverter Fail Signal Stuck On
P0A944B (Hybrid (EV) Control System) DC/DC Converter "A" Over Temperature
P0A949E (Hybrid (EV) Control System) DC/DC Converter "A" Fail Signal Stuck On
P1A0F00 (Hybrid (EV) Control System) DC/DC Converter "A" Overvoltage (Control Module Performance)
P1A2F00 (Hybrid (EV) Control System) DC/DC Converter "A" Overvoltage (Position Sensor Circuit Range/Performance)
P1A6F00 (Hybrid (EV) Control System) DC/DC Converter "A" Overvoltage (Inverter Performance)
P1A7F00 (Hybrid (EV) Control System) DC/DC Converter "A" Overvoltage (System Performance)
P1A9400 (Hybrid (EV) Control System) DC/DC Converter "A" Overcurrent (Control Module Performance)
P1A9900 (Hybrid (EV) Control System) DC/DC Converter "A" Overcurrent (Position Sensor Circuit Range/Performance)
P1AA400 (Hybrid (EV) Control System) DC/DC Converter "A" Overcurrent (Inverter Performance)
P1AA900 (Hybrid (EV) Control System) DC/DC Converter "A" Overcurrent (System Performance)
P1AB400 (Hybrid (EV) Control System) Drive Motor "A" Inverter Circuit Short (Control Module Performance)
P1AB900 (Hybrid (EV) Control System) Drive Motor "A" Inverter Circuit Short (Position Sensor Circuit Range/Performance)
P1ABF00 (Hybrid (EV) Control System) Drive Motor "A" Inverter Circuit Short (Inverter Performance)
P1AC300 (Hybrid (EV) Control System) Drive Motor "A" Inverter Circuit Short (System Performance)
P1C8449 (Hybrid (EV) Control System) High Voltage Power Resource Circuit Short during Ready ON
P1CB59E (Hybrid (EV) Control System) DC/DC Converter "A" Overvoltage Signal Stuck On
P1D824B (Hybrid (EV) Control System) FC Air Compressor Inverter Over Temperature
P1D829E (Hybrid (EV) Control System) FC Air Compressor Inverter Fail Signal Stuck On
P1EF800 (Hybrid (EV) Control System) FC Air Compressor Inverter Circuit Short (Control Module Performance)
P1EF900 (Hybrid (EV) Control System) FC Air Compressor Inverter Circuit Short (Position Sensor Circuit Range/Performance)
P1EFA00 (Hybrid (EV) Control System) FC Air Compressor Inverter Circuit Short (System Performance)
P1EFB00 (Hybrid (EV) Control System) FC Air Compressor Inverter Circuit Short (Inverter Performance)
P31B300 (Hybrid (EV) Control System) Hybrid/EV Battery Voltage High


HINT:

DTC P1D2F96 may be store due to problems that cause the DTCs shown above to be output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order starting with the listed DTCs shown in the table above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA

C

2.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None


Procedure1

a.

Read the freeze frame data of DTC P1D2F96.

Powertrain > EV > DTC(P1D2F96) > Freeze Frame Data
Tester Display
FC Coolant Pump Main Power Supply Status
FC Coolant Pump Output Status
FC Coolant Pump Load Status
FC Coolant Pump Over Temperature Status
Lost Communication with FC Coolant Pump
FC Coolant Pump CPU Abnormal
50040 397 910,911,912,913,828,829 P1D2F96
Result:
Result Proceed to
The "Lost Communication with FC Coolant Pump" of the freeze frame data shows ON. A
The "FC Coolant Pump Output Status" of the freeze frame data shows Circuit Open. B
The "FC Coolant Pump Main Power Supply Status" of the freeze frame data shows Low Voltage. C
The "FC Coolant Pump Main Power Supply Status" of the freeze frame data shows Overvoltage.
The "FC Coolant Pump Load Status" of the freeze frame data shows Inverter Output Voltage Saturation.
The "FC Coolant Pump Over Temperature Status" of the freeze frame data shows Over Temperature.
The "FC Coolant Pump CPU Abnormal" of the freeze frame data shows ON.
Other than above. D



Post-procedure1

a.

Turn the ignition switch off.



A

B

3.CHECK FC COOLING WATER PUMP ASSEMBLY

C

REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

HINT:

Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time



D

5.REPLACE FC COOLING WATER PUMP ASSEMBLY
3.CHECK FC COOLING WATER PUMP ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to EV supply battery assembly and the FC converter power outlet cable (inverter with converter assembly) is not connected to the FC converter assembly.

NOTICE:

After removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A476946

Disconnect the FC cooling water pump cable connector from the FC cooling water pump assembly.


Procedure1

a.
A480724C02
0.865,2.99 1.438,2.281 true 1.385,3.104 1.583,2.281 true 2.083,3.115 1.75,2.26 true 0.469,1.708 1.385,2.146 true 0.177,0.365 0.49,0.563 0.313,0.198 10 false *a 0.771,3.031 0.927,3.229 0.156,0.198 10 false U 1.333,3.135 1.49,3.333 0.156,0.198 10 false V 2.052,3.188 2.208,3.385 0.156,0.198 10 false W 0.271,1.604 0.583,1.802 0.313,0.198 10 false *b
*a Component without harness connected
(FC Cooling Water Pump Assembly)
*b Shield Ground


Check the FC cooling water pump for an interphase short using a milliohmmeter.

i.

Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the FC cooling water pump temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
Tester Connection Condition Specified Condition
W - V Ignition switch off 704 to 810 mΩ
W - U Ignition switch off 707 to 813 mΩ
V - U Ignition switch off 705 to 811 mΩ


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F).)




b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
W - Body ground and shield ground Ignition switch off 10 MΩ or higher
V - Body ground and shield ground Ignition switch off 10 MΩ or higher
U - Body ground and shield ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the FC cooling water pump cable connector to the FC cooling water pump assembly.



OK

4.CHECK FC COOLING WATER PUMP CABLE

NG

REPLACE FC COOLING WATER PUMP ASSEMBLY

4.CHECK FC COOLING WATER PUMP CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to EV supply battery assembly and the FC converter power outlet cable (inverter with converter assembly) is not connected to the FC converter assembly.

NOTICE:

After removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479001

Disconnect the FC cooling water pump cable connector from the FC cooling water pump inverter assembly.


c.
A476946

Disconnect the FC cooling water pump cable connector from the FC cooling water pump assembly.


Procedure1

a.
A478997C03
0.302,1.406 0.74,1.688 0.438,0.281 0.365,3.438 0.802,3.719 0.438,0.281 1.833,1.375 2.375,0.885 true 1.854,3.375 2.396,2.885 true 1.458,1.719 1.177,2.177 true 1.469,3.729 1.125,4.135 true 1.729,1.729 1.74,2.198 true 1.719,3.729 1.729,4.198 true 1.99,3.75 2.354,4.146 true 1.979,1.719 2.344,2.115 true 0.531,0.458 0.844,0.656 0.313,0.198 10 false *a 0.542,2.802 0.854,3 0.313,0.198 10 false *b 2.427,0.75 2.74,0.948 0.313,0.198 10 false *1 2.479,2.771 2.792,2.969 0.313,0.198 10 false *1 2.313,2.146 2.635,2.354 0.323,0.208 10 false U 2.385,4.208 2.698,4.406 0.313,0.198 10 false U 1.083,2.188 1.417,2.385 0.333,0.198 10 false W 1.688,4.281 2,4.479 0.313,0.198 10 false V 1.677,2.26 2.01,2.458 0.333,0.198 10 false V 1.01,4.146 1.344,4.344 0.333,0.198 10 false W 0.427,1.448 0.74,1.646 0.313,0.198 10 false b1 0.5,3.51 0.813,3.708 0.313,0.198 10 false b2
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Cooling Water Pump Inverter Assembly Side)
*b FC Cooling Water Pump Cable
(FC Cooling Water Pump Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1,b2)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

Click Connector(b2)Engine Compartment>FC Cooling Water Pump Cable>FC Cooling Water Pump Assembly

b1-1 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b2-1 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b2-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b2-3 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1,b2)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

Click Connector(b2)Engine Compartment>FC Cooling Water Pump Cable>FC Cooling Water Pump Assembly

b1-1 (W) - b2-1 (W) Ignition switch off Below 1 Ω
b1-2 (V) - b2-2 (V) Ignition switch off Below 1 Ω
b1-3 (U) - b2-3 (U) Ignition switch off Below 1 Ω
b1-1 (W) - b2-3 (U) Ignition switch off 100 MΩ or higher
b1-2 (V) - b2-1 (W) Ignition switch off 100 MΩ or higher
b1-3 (U) - b2-2 (V) Ignition switch off 100 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the FC cooling water pump cable connector to the FC cooling water pump inverter assembly.


b.

Reconnect the FC cooling water pump cable connector to the FC cooling water pump assembly.



OK

REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

HINT:

Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time



NG

REPLACE FC COOLING WATER PUMP CABLE

5.REPLACE FC COOLING WATER PUMP ASSEMBLY
HINT:

Click hereEngine / Hybrid System>COOLING>WATER PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE FC COOLANT PUMP)
7.PERFORM ACTIVE TEST USING GTS (CONTROL THE FC COOLANT PUMP)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

Check "FC Coolant Pump Load Status" and "FC Coolant Pump Start Fail" after performing the Active Test for 30 seconds or more at 1000 rpm and 2000 rpm.

Powertrain > EV > Active Test
Active Test Display
Control the FC Coolant Pump
Data List Display
FC Coolant Pump Drive Speed
FC Coolant Pump Speed
Target FC Coolant Pump Speed
FC Coolant Pump Load Status
FC Coolant Pump Start Fail
50004 397 17 704,909,908,912,831
Result:
Result Proceed to
"FC Coolant Pump Load Status" shows Normal and "FC Coolant Pump Start Fail" shows OFF A
Other than above. B



Post-procedure1

a.

Turn the ignition switch off.



A

8.SIMULATION TEST

B

REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

HINT:

Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time



8.SIMULATION TEST
a.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF. Then, wait for 1 minute or more.


Powertrain > EV > Data List
Tester Display
FC Work Mode
FC Intermittent Operation
50003 397 962,872
Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1D2F96 is output A
DTCs are not output B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE FC COOLING WATER PUMP INVERTER ASSEMBLY
HINT:

Replace both the FC cooling water pump inverter assembly and FC hydrogen pump inverter assembly at the same time



B

END