Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1F451F  FC Converter Control Module Power Relay Sense Circuit Intermittent  


DESCRIPTION

The FC boost control ECU is located inside the FC converter assembly. It monitors the +B power source voltage and detects a momentary interruption.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent The FC boost control ECU was reset due to a momentary interruption of the power supply while the ignition switch is ON (READY).
(1 trip detection logic)
·

Auxiliary battery

·

IGCT NO. 2 relay

·

FC boost control ECU

·

No. 1 FC converter wire

·

No. 2 FC converter wire

·

Wire harness or connector


Master Warning: Comes on FCDC A

WIRING DIAGRAM

A336294E03
0.844,1.271 1.688,1.604 0.844,0.333 10 false IGCT NO. 1 0.844,1.958 1.458,2.156 0.615,0.198 10 false R/R RB# 2 1.021,2.729 2.24,2.917 1.219,0.188 10 false Auxiliary Battery 2.271,0.719 2.427,0.917 0.156,0.198 10 false 3 2.271,1.167 2.427,1.365 0.156,0.198 10 false 1 3.083,0.719 3.24,0.917 0.156,0.198 10 false 5 3.083,1.167 3.24,1.365 0.156,0.198 10 false 2 4.844,0.323 5.073,0.51 0.229,0.188 10 false 12 4.854,0.719 5.115,0.938 0.26,0.219 10 false 13 5.115,0.323 5.573,0.521 0.458,0.198 10 false +B1 5.125,0.729 5.583,0.927 0.458,0.198 10 false +B2 5.365,1.75 5.823,1.948 0.458,0.198 10 false B6 5.219,1.333 6.635,1.667 1.417,0.333 10 false FC Boost Control ECU 5.688,2.573 6.302,2.771 0.615,0.198 10 false MREL 5.615,3.229 6.635,3.479 1.021,0.25 10 false A8*1 2.354,1.542 3.135,1.813 0.781,0.271 10 false IGCT NO. 1 5.354,1.906 6.875,2.094 1.521,0.188 10 false FC Converter Assembly 5.615,3.385 6.906,3.615 1.292,0.229 10 false EV Control ECU 5.448,2.573 5.688,2.802 0.24,0.229 10 false 21 3.427,1 4.208,1.271 0.781,0.271 10 false IGCT NO. 7 5.99,3.24 7.01,3.49 1.021,0.25 10 false D15*2 2.385,3.083 3.406,3.333 1.021,0.25 10 false *1: for LHD 2.385,3.417 3.406,3.667 1.021,0.25 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

A484004

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side.

Make sure to remove the EV supply battery assembly service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (w/ 1500W Type Voltage Inverter)


·
A341450

After removing the service plug grip from the EV supply battery assembly, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system. After removing the FC converter power outlet cable (inverter with converter assembly) on FC converter side and use the "HIGH-VOLTAGE, DO NOT TOUCH" sign to notify other technicians that you are working on the high-voltage system.

·
A484005

After removal of the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching the high-voltage connectors and terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

When reinstalling the service plug grip to the EV supply battery assembly, after lowering the EV supply battery assembly service plug grip 90°, securely slide it until a "click" sound is heard.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PRECAUTION

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.



PROCEDURE

1.CHECK AUXILIARY BATTERY TERMINAL
a.

Confirm whether the auxiliary battery terminals have been disconnected recently.


Result:
Result Proceed to
Terminals have been disconnected A
Terminals have not been disconnected B



A

2.CHECK WARNING LIGHT (MASTER WARNING LIGHT)

B

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
2.CHECK WARNING LIGHT (MASTER WARNING LIGHT)

Pre-procedure1

a.

With the ignition switch off, turn the ignition switch to ON (READY) and wait for 30 seconds or more.


Procedure1

a.

Confirm that the master warning light illuminates.

Result:
Result Proceed to
Master warning light illuminates A
Master warning light does not illuminate B


HINT:

DTC P1F451F may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the ignition switch is turned off and then to ON (READY) again. In this case, clear DTCs to complete the inspection.



Post-procedure1

a.

Turn the ignition switch off.



A

3.CLEAR DTC

B

END

3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > FCDC > Clear DTCs
50002 493
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

4.CHECK DTC OUTPUT (FCDC)
4.CHECK DTC OUTPUT (FCDC)

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.


Procedure1

a.

Check for DTCs.

Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
Only P1F451F is output A
P1F451F and other DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)

B

GO TO DTC CHART

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the auxiliary battery terminal.

OK:

The terminal is connected securely and there is no contact problem.



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector) C



A

7.INSPECT RELAY (IGCT NO. 1 RELAY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT RELAY (IGCT NO. 1 RELAY)

OK

8.CHECK HARNESS AND CONNECTOR (FC CONVERTER ASSEMBLY - IGCT NO. 1 RELAY)

NG

REPLACE RELAY (IGCT NO. 1 RELAY)

8.CHECK HARNESS AND CONNECTOR (FC CONVERTER ASSEMBLY - IGCT NO. 1 RELAY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed to EV supply battery assembly and the FC converter power outlet cable (inverter with converter assembly) is not connected to the FC converter assembly.

NOTICE:

After removing the EV supply battery assembly service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the IGCT NO. 1 relay from the No. 1 front compartment relay block.


c.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



d.
A479997

Disconnect the FC converter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B6)Location & Routing

Click Connector(B6)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

B6-12 (+B1) - 5 (IGCT NO. 1 relay holder) Ignition switch off Below 1 Ω
B6-13 (+B2) - 5 (IGCT NO. 1 relay holder) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO. 1 relay.


b.

Connect the FC converter assembly connector.


c.

Install the electric heater sub-assembly.



OK

REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

·

FC boost control ECU

·

No. 1 FC converter wire

·

No. 2 FC converter wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR