Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A1B1F  Drive Motor "A" Control Module Circuit Intermittent  


DESCRIPTION

If the MG ECU, which is built into in the inverter with converter assembly, is reset due to a problem with the power source in the inverter, the EV control ECU will stored this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent Error in reset signal from the inverter assembly power source IC:
If internal power source voltage drops below the normal CPU operating voltage or the ROM/RAM is malfunctioning, the power source IC resets the MG ECU and stores this DTC.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

auxiliary battery terminal


Master Warning:
Comes on
EV A

WIRING DIAGRAM

for LHD:
A479451E01
0.073,1.104 0.969,1.677 0.896,0.573 10 false From Auxiliary Battery 1.281,1.354 2.052,1.646 0.771,0.292 10 false IGCT NO.1 3.375,1.354 4.542,1.583 1.167,0.229 10 false IGCT NO.4 2.281,1.865 2.99,2.115 0.708,0.25 10 false IGCT NO.1 3.75,2.333 4.24,2.583 0.49,0.25 10 false MREL 3.688,2.927 4.063,3.177 0.375,0.25 10 false A8 5.646,3.583 6.021,3.833 0.375,0.25 10 false A19 5.656,3.771 7.094,4.188 1.438,0.417 10 false Inverter with Converter Assembly 3.677,3.115 5.302,3.281 1.625,0.167 10 false EV Control ECU 5.729,1.219 6.104,1.469 0.375,0.25 10 false +B 5.74,1.896 6.115,2.146 0.375,0.25 10 false +B2 5.719,2.49 6.188,2.677 0.469,0.188 10 false GND1 5.729,3.063 6.229,3.26 0.5,0.198 10 false GND2 5.438,1.333 5.698,1.615 0.26,0.281 10 false 10 5.448,2.01 5.708,2.292 0.26,0.281 10 false 11 5.458,3.188 5.719,3.469 0.26,0.281 10 false 31 5.458,2.604 5.719,2.885 0.26,0.281 10 false 30 3.479,2.208 3.813,2.49 0.333,0.281 10 false 21 3.813,1.042 4.073,1.323 0.26,0.281 10 false 2 3.552,1.042 3.813,1.323 0.26,0.281 10 false 1 1.479,1.052 1.74,1.333 0.26,0.281 10 false 1 1.729,1.052 1.99,1.333 0.26,0.281 10 false 2 2.927,1.479 3.188,1.76 0.26,0.281 10 false 2 2.219,1.479 2.479,1.76 0.26,0.281 10 false 1 2.219,1.094 2.479,1.375 0.26,0.281 10 false 3 2.927,1.115 3.188,1.396 0.26,0.281 10 false 5

for RHD:
A479451E02
0.063,1.125 0.99,1.646 0.927,0.521 10 false From Auxiliary Battery 1.281,1.354 2.052,1.646 0.771,0.292 10 false IGCT NO.1 3.375,1.354 4.542,1.583 1.167,0.229 10 false IGCT NO.4 2.281,1.865 2.99,2.115 0.708,0.25 10 false IGCT NO.1 3.75,2.333 4.24,2.583 0.49,0.25 10 false MREL 3.615,2.927 3.99,3.177 0.375,0.25 10 false D15 5.469,3.583 5.844,3.833 0.375,0.25 10 false A18 5.458,3.75 6.896,4.167 1.438,0.417 10 false Inverter with Converter Assembly 3.625,3.083 5.25,3.25 1.625,0.167 10 false EV Control ECU 5.729,1.219 6.104,1.469 0.375,0.25 10 false +B 5.74,1.896 6.115,2.146 0.375,0.25 10 false +B2 5.719,2.49 6.208,2.74 0.49,0.25 10 false GND1 5.729,3.063 6.229,3.313 0.5,0.25 10 false GND2 5.438,1.333 5.698,1.615 0.26,0.281 10 false 10 5.448,2.01 5.708,2.292 0.26,0.281 10 false 11 5.458,3.188 5.719,3.469 0.26,0.281 10 false 31 5.458,2.604 5.719,2.885 0.26,0.281 10 false 30 3.479,2.208 3.813,2.49 0.333,0.281 10 false 21 3.813,1.031 4.073,1.313 0.26,0.281 10 false 2 3.552,1.031 3.813,1.313 0.26,0.281 10 false 1 1.479,1.052 1.74,1.333 0.26,0.281 10 false 1 1.729,1.052 1.99,1.333 0.26,0.281 10 false 2 2.917,1.5 3.177,1.781 0.26,0.281 10 false 2 2.219,1.5 2.479,1.781 0.26,0.281 10 false 1 2.219,1.115 2.479,1.396 0.26,0.281 10 false 3 2.927,1.115 3.188,1.396 0.26,0.281 10 false 5

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 15 seconds or more.

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0A1B1F is output A
P0A1B1F and any DTCs in the table below are output B


Malfunction Content Relevant DTC
Communication system malfunction P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
P312487 Communication Error from Hybrid/EV Powertrain Control Module to Drive Motor Control Module "A" Missing Message

HINT:
·

P0A1B1F may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT NO. 1 RELAY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT NO. 1 RELAY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Remove the IGCT NO. 1 relay from the luggage room relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479450C03
3.813,0.958 4.26,1.302 0.448,0.344 3.813,1.479 4.26,1.823 0.448,0.344 5.469,2.177 5.76,1.583 true 6.177,2.167 5.865,1.583 true 5.875,1.333 6.167,0.719 true 5.75,1.333 5.458,0.729 true 0.438,0.083 0.75,0.24 0.313,0.156 10 false *1 2.854,0.573 3.167,0.729 0.313,0.156 10 false *2 3.667,0.073 3.979,0.229 0.313,0.156 10 false *a 6.063,0.583 6.521,0.781 0.458,0.198 10 false +B2 3.938,1.063 4.396,1.26 0.458,0.198 10 false A19 5.375,0.583 5.833,0.781 0.458,0.198 10 false +B 5.344,2.167 5.802,2.365 0.458,0.198 10 false GND1 6.042,2.167 6.5,2.365 0.458,0.198 10 false GND2 3.927,1.563 4.385,1.76 0.458,0.198 10 false A18 4.333,1.052 4.646,1.25 0.313,0.198 10 false *A 4.344,1.542 4.656,1.74 0.313,0.198 10 false *B
*A for LHD *B for RHD
*1 Luggage Room Relay Block *2 IGCT NO. 1 Relay Holder
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-10 (+B) - 5 (IGCT NO.1 relay holder) Ignition switch off Below 1 Ω
A19-11 (+B2) - 5 (IGCT NO.1 relay holder) Ignition switch off Below 1 Ω
A19-30 (GND1) - Body ground Ignition switch off Below 1 Ω
A19-31 (GND2) - Body ground Ignition switch off Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-10 (+B) - 5 (IGCT NO.1 relay holder) Ignition switch off Below 1 Ω
A18-11 (+B2) - 5 (IGCT NO.1 relay holder) Ignition switch off Below 1 Ω
A18-30 (GND1) - Body ground Ignition switch off Below 1 Ω
A18-31 (GND2) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the IGCT NO. 1 relay.


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR