Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A3F16  Drive Motor "A" Position Sensor Circuit Voltage Below Threshold  P0A3F1C  Drive Motor "A" Position Sensor Circuit Voltage Out of Range  P0A3F22  Drive Motor "A" Position Sensor Signal Amplitude > Maximum  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs indicate the resolver output signal is abnormal. The cause of this malfunction may be one of the following:

Area Main Malfunction Description
Inverter low-voltage circuit The connectors are not connected properly
Resolver
·

Open or short circuit in the resolver for drive motor control

·

Internal drive motor malfunction (entry of foreign matter, etc.)


Wire harness between the resolver and inverter with converter assembly
·

Open or short circuit in the wire harness

·

The connectors are not connected properly


Inside of inverter Inverter with converter assembly internal circuit malfunction


DESCRIPTION

Refer to the system description for the motor resolver circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor Resolver Circuit

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold Interphase short in the drive motor resolver circuit:
A short circuit between signal lines of drive motor resolver phases is electrically detected.
(1 trip detection logic)
·

Inverter with converter assembly

·

FCV with motor transaxle assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range Drive motor resolver signal is out of the normal range (amplitude is too large or too small).
(1 trip detection logic)
·

Inverter with converter assembly

·

FCV with motor transaxle assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum Open or short in the drive motor resolver circuit:
Drive motor resolver signal is out of the normal range (amplitude is extremely small).
(1 trip detection logic)
·

Inverter with converter assembly

·

FCV with motor transaxle assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 5 seconds or more.

2.

Enter the following menus: Powertrain / EV / Data List / FC Work Mode, FC Intermittent Operation.

3.

Push the P position switch (shift position indicator) to select park (P), turn the ignition switch to ON (READY) and wait until the FC system is started. Waiting for at least 2 minutes is required after turning the ignition switch to ON (READY).

-

FC system is started: "Working" is displayed for the Data List item "FC Work Mode" and "FC Intermittent Operation" is OFF.


4.

With the FC system operating, wait for 15 seconds or more.

5.

Drive the vehicle in drive (D) for 5 m (16 ft.) or more.

6.

Drive the vehicle in reverse (R) for 5 m (16 ft.) or more.

7.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the motor resolver circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Motor Resolver Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

At least 10 minutes are necessary to discharge the high-voltage capacitors inside the inverter with converter assembly and FC stack assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0A3F16, P0A3F1C or P0A3F22 is output, or DTCs other than P06B01C, P06E61C, P06D61C or P1C731C are output simultaneously A
P06B01C, P06E61C, P06D61C or P1C731C is output simultaneously B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK MOTOR RESOLVER CIRCUIT

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MOTOR RESOLVER CIRCUIT

NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY