Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1E9362  FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Compare Failure  P1E9462  FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Compare Failure  P1F0E1C  FC Air Compressor Motor Phase V Current Sensor "A" Circuit Voltage Out of Range  P1F0F1C  FC Air Compressor Motor Phase W Current Sensor "A" Circuit Voltage Out of Range  P1F101C  FC Air Compressor Motor Phase V Current Sensor "B" Circuit Voltage Out of Range  P1F111C  FC Air Compressor Motor Phase W Current Sensor "B" Circuit Voltage Out of Range  P1F1228  FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure  P1F1328  FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs indicate the current sensor value is abnormal. The cause of this malfunction may be one of the following:

Internal inverter malfunction

Inverter with converter assembly internal circuit malfunction


Inverter low-voltage circuit malfunction

The connectors are not connected properly



DESCRIPTION

The MG ECU, which is built into the inverter with converter assembly, monitors the main and sub sensors of the FC air compressor motor inverter current sensor. Following DTCs indicate malfunctions in the current sensors, and do not indicate malfunctions in the high-voltage system.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E9362 FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Compare Failure Malfunction in FC air compressor motor inverter current sensor (performance problem or open phase V):*
The difference between the output of the phase V main sensor and phase V sub sensor is larger than the standard.
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1E9462 FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Compare Failure Malfunction in FC air compressor motor inverter current sensor (performance problem or open phase W):*
The difference between the output of the phase W main sensor and phase W sub sensor is larger than the standard.
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1F0E1C FC Air Compressor Motor Phase V Current Sensor "A" Circuit Voltage Out of Range Malfunction in FC air compressor motor inverter current sensor (phase V main sensor)*
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1F0F1C FC Air Compressor Motor Phase W Current Sensor "A" Circuit Voltage Out of Range Malfunction in FC air compressor motor inverter current sensor (phase W main sensor)*
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1F101C FC Air Compressor Motor Phase V Current Sensor "B" Circuit Voltage Out of Range Malfunction in FC air compressor motor inverter current sensor (phase V sub sensor)*
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1F111C FC Air Compressor Motor Phase W Current Sensor "B" Circuit Voltage Out of Range Malfunction in FC air compressor motor inverter current sensor (phase W sub sensor)*
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1F1228 FC Air Compressor Motor Phase V Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure Malfunction in FC air compressor motor inverter current sensor (phase V main and sub sensors offset)*
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A
P1F1328 FC Air Compressor Motor Phase W Current Sensor "A"/"B" Signal Bias Level Out of Range / Zero Adjustment Failure Malfunction in FC air compressor motor inverter current sensor (phase W main and sub sensors offset)*
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector


Master Warning:
Comes on
EV A

*: DTC is stored when the current sensor signal is out of the normal range.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 5 seconds or more.

2.

Turn the ignition switch to ON (READY) with push the P position switch (shift position indicator) to select park (P) and wait for 5 seconds or more.

3.

Move the shift lever to select shift state neutral (N) and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV / Data List / FC Work Mode, FC Intermittent Operation.

5.

Push the P position switch (shift position indicator) to select park (P), turn the ignition switch to ON (READY) and wait until the FC system is started. Waiting for at least 2 minutes is required after turning the ignition switch to ON (READY).

-

FC system is started: "Working" is displayed for the Data List (FC) item "FC Work Mode" and "FC Intermittent Operation" is OFF.


6.

With the FC system operating, wait for 15 seconds or more.

7.

Drive the vehicle in drive (D) for 5 m (16 ft.) or more.

8.

Drive the vehicle in reverse (R) for 5 m (16 ft.) or more.

9.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1E9362, P1E9462, P1F0E1C, P1F0F1C, P1F101C, P1F111C, P1F1228 or P1F1328 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B

Malfunction Content Relevant DTC
Insulation Malfunction P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
P1EEC49 Hybrid/EV Battery Voltage System Isolation (FC Air Compressor Area) Internal Electronic Failure
P1EED49 Hybrid/EV Battery Voltage System Isolation (FC Area) Internal Electronic Failure
P1EEE49 Hybrid/EV Battery Voltage System Isolation (Hydrogen Pump Area) Internal Electronic Failure
P1EEF49 Hybrid/EV Battery Voltage System Isolation (FC Coolant Pump Area) Internal Electronic Failure
High Voltage Circuit Malfunction P0AA649 Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure


HINT:

P1E9362, P1E9462, P1F0E1C, P1F0F1C, P1F101C, P1F111C, P1F1228 or P1F1328 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR