Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Motor High-voltage Circuit  


DESCRIPTION

The cause of the malfunction may be the high-voltage circuit of the motor.

Check the motor internal resistance and the connection condition of the high-voltage line between the inverter and motor to check whether there is an open or short circuit.

Related Parts Check
Area Inspection
Motor cable connection check Check for open or short circuit in the connection condition of the cable from the inverter to the motor.
Motor, motor cable and No. 2 battery pack wire Check the motor (including cable) internal resistance and insulation resistance with body ground to check for an open or short circuit.

WIRING DIAGRAM

for LHD:
A481333E04
5.115,0.292 5.573,0.49 0.458,0.198 10 false R-U 5.115,0.729 5.573,0.927 0.458,0.198 10 false R-W 5.115,1.188 5.573,1.385 0.458,0.198 10 false R-V 5.104,1.625 6.479,1.823 1.375,0.198 10 false PCU_MOTOR 5.083,1.938 5.396,2.135 0.313,0.198 10 false O2 3.917,0.292 4.229,0.49 0.313,0.198 10 false O3 3.917,0.74 4.229,0.938 0.313,0.198 10 false O3 3.927,1.188 4.24,1.385 0.313,0.198 10 false O3 3.302,0.271 3.615,0.469 0.313,0.198 10 false q2 3.292,0.719 3.604,0.917 0.313,0.198 10 false q2 3.292,1.188 3.604,1.385 0.313,0.198 10 false q2 3.313,1.635 3.625,1.833 0.313,0.198 10 false q2 2.135,0.177 2.292,0.375 0.156,0.198 10 false U 2.125,0.625 2.281,0.823 0.156,0.198 10 false W 2.146,1.073 2.302,1.271 0.156,0.198 10 false V 0.844,1.906 1.156,2.104 0.313,0.198 10 false q1 4.906,0.115 5.063,0.313 0.156,0.198 10 false 3 4.927,0.573 5.083,0.771 0.156,0.198 10 false 1 4.938,1.031 5.094,1.229 0.156,0.198 10 false 2 3.969,0.531 4.125,0.729 0.156,0.198 10 false 3 3.958,0.979 4.115,1.177 0.156,0.198 10 false 2 3.969,0.073 4.125,0.271 0.156,0.198 10 false 1 3.354,0.073 3.51,0.271 0.156,0.198 10 false 1 3.344,0.521 3.5,0.719 0.156,0.198 10 false 3 3.354,0.979 3.51,1.177 0.156,0.198 10 false 2 3.354,1.427 3.51,1.625 0.156,0.198 10 false 4 2.396,0.156 2.552,0.354 0.156,0.198 10 false 3 2.385,0.583 2.542,0.781 0.156,0.198 10 false 1 2.406,1.031 2.563,1.229 0.156,0.198 10 false 2 2.396,1.51 2.552,1.708 0.156,0.198 10 false 4 5.052,2.135 7.156,2.385 2.104,0.25 10 false Inverter with Converter Assembly 0.833,2.125 3.24,2.365 2.406,0.24 10 false FCV with Motor Transaxle Assembly 0.594,2.448 3.5,2.646 2.906,0.198 10 false : High Voltage Line 3.271,1.948 5.563,2.146 2.292,0.198 10 false Connector Cover

for RHD:
A481333E02
5.115,0.292 5.573,0.49 0.458,0.198 10 false R-U 5.115,0.729 5.573,0.927 0.458,0.198 10 false R-W 5.115,1.188 5.573,1.385 0.458,0.198 10 false R-V 5.104,1.625 6.479,1.823 1.375,0.198 10 false PCU_MOTOR 5.083,1.938 5.396,2.135 0.313,0.198 10 false O1 3.917,0.292 4.229,0.49 0.313,0.198 10 false O3 3.917,0.74 4.229,0.938 0.313,0.198 10 false O3 3.927,1.188 4.24,1.385 0.313,0.198 10 false O3 3.302,0.271 3.615,0.469 0.313,0.198 10 false q2 3.292,0.719 3.604,0.917 0.313,0.198 10 false q2 3.292,1.188 3.604,1.385 0.313,0.198 10 false q2 3.313,1.635 3.625,1.833 0.313,0.198 10 false q2 2.135,0.177 2.292,0.375 0.156,0.198 10 false U 2.125,0.625 2.281,0.823 0.156,0.198 10 false W 2.146,1.073 2.302,1.271 0.156,0.198 10 false V 0.844,1.906 1.156,2.104 0.313,0.198 10 false q1 4.906,0.115 5.063,0.313 0.156,0.198 10 false 1 4.927,0.573 5.083,0.771 0.156,0.198 10 false 3 4.938,1.031 5.094,1.229 0.156,0.198 10 false 2 3.969,0.531 4.125,0.729 0.156,0.198 10 false 3 3.958,0.979 4.115,1.177 0.156,0.198 10 false 2 3.969,0.073 4.125,0.271 0.156,0.198 10 false 1 3.354,0.073 3.51,0.271 0.156,0.198 10 false 1 3.344,0.521 3.5,0.719 0.156,0.198 10 false 3 3.354,0.979 3.51,1.177 0.156,0.198 10 false 2 3.354,1.427 3.51,1.625 0.156,0.198 10 false 4 2.396,0.156 2.552,0.354 0.156,0.198 10 false 3 2.385,0.583 2.542,0.781 0.156,0.198 10 false 1 2.406,1.031 2.563,1.229 0.156,0.198 10 false 2 2.396,1.51 2.552,1.708 0.156,0.198 10 false 4 5.052,2.135 7.156,2.385 2.104,0.25 10 false Inverter with Converter Assembly 0.833,2.125 3.208,2.375 2.375,0.25 10 false FCV with Motor Transaxle Assembly 0.594,2.448 3.5,2.646 2.906,0.198 10 false : High Voltage Line 3.271,1.948 5.563,2.146 2.292,0.198 10 false Connector Cover

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK CONVERTER WITH INVERTER ASSEMBLY (NO. 2 BATTERY PACK WIRE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter terminal cover from the inverter with converter assembly.


Procedure1

a.
C371865C04
0.021,0.021 0.333,0.26 0.313,0.24 12 true *A 0.021,2.458 0.313,2.698 0.292,0.24 12 true *B
*A for LHD
*B for RHD


Check that the bolts for the No. 2 battery pack wire are tightened to the specified torque, the No. 2 battery pack wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.

Disconnect the No. 2 battery pack wire from the inverter with converter assembly.


c.

Check for arc marks at the terminals for the No. 2 battery pack wire.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Connect the No. 2 battery pack wire to the inverter with converter assembly.


b.

Install the inverter terminal cover.



A

2.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

2.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter terminal cover from the inverter with converter assembly.


c.

Disconnect the No. 2 battery pack wire from the inverter with converter assembly.


Procedure1

a.
C371859C11
0.302,3.073 0.708,3.427 0.406,0.354 0.156,0.875 0.563,1.229 0.406,0.354 1.083,0.583 0.917,0.417 false 1.365,0.583 1.396,0.208 false 1.677,0.552 2.021,0.313 false 2.406,0.698 2.24,0.844 false 1.667,2.813 1.49,2.521 false 1.958,2.813 2.281,2.167 false 2.26,2.813 2.417,2.521 false 0.948,2.938 1.167,3.104 false 0.448,0.219 0.969,0.417 0.521,0.198 10 false 3 (R-U) 1.427,0.094 1.99,0.281 0.563,0.188 10 false 2 (R-V) 2.063,0.229 2.677,0.417 0.615,0.188 10 false 1 (R-W) 2.417,0.563 2.635,0.75 0.219,0.188 10 false *1 0.083,0.094 0.302,0.281 0.219,0.188 10 false *a 0.448,0.531 0.76,0.729 0.313,0.198 12 false *A 0.417,3.167 0.729,3.365 0.313,0.198 10 false O1 2.448,2.417 3.042,2.635 0.594,0.219 10 false 3 (R-W) 2.333,2.073 2.917,2.271 0.583,0.198 10 false 2 (R-V) 1,2.427 1.563,2.625 0.563,0.198 10 false 1 (R-U) 0.729,2.792 0.948,2.979 0.219,0.188 10 false *1 0.656,2.365 0.969,2.563 0.313,0.198 12 false *B 0.281,0.969 0.594,1.167 0.313,0.198 10 false O2
*A for LHD
*B for RHD
*1 Shield Ground
*a No. 2 Battery Pack Wire
(Inverter with Converter Assembly Side)


Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the motor (MG2) temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O2-1 (R-W) - O2-3 (R-U) Ignition switch off 70.2 to 78.1 mΩ
O2-3 (R-U) - O2-2(R-V) Ignition switch off 70.3 to 78.2 mΩ
O2-2(R-V) - O2-1 (R-W) Ignition switch off 70.0 to 77.9 mΩ

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O1-3 (R-W) - O1-1 (R-U) Ignition switch off 70.2 to 78.1 mΩ
O1-1 (R-U) - O1-2 (R-V) Ignition switch off 70.3 to 78.2 mΩ
O1-2(R-V) - O1-3 (R-W) Ignition switch off 70.0 to 77.9 mΩ


HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}

The calculation is based on the following:

R20: Resistance at 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C (°F).)



b.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O2-1 (R-W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O2-3 (R-U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O2-2 (R-V) - Body ground and shield ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O1-3 (R-W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O1-1 (R-U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O1-2 (R-V) - Body ground and shield ground Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 2 battery pack wire.


b.

Install the inverter terminal cover.



OK

MOTOR HIGH-VOLTAGE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

3.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)
3.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A480834

Check that the bolts for the motor cable are tightened to the specified torque, the motor cable is connected securely, and there are no contact problems.

Specified Condition:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)



d.

Disconnect the motor cable from the FCV with motor transaxle assembly.


Procedure1

a.

Check for arc marks at the terminals for the motor cable.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Connect the motor cable to the FCV with motor transaxle assembly.


b.

Install the connector cover.



A

4.CHECK NO. 2 BATTERY PACK WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

4.CHECK NO. 2 BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 battery pack wire.

HINT:

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

a.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


A485151C01
1.146,0.167 1.583,0.51 0.438,0.344 3.229,0.167 3.667,0.51 0.438,0.344 6.01,0.167 6.448,0.51 0.438,0.344 3.167,0.917 2.76,1.802 true 3.417,0.917 3.479,2.167 true 3.677,0.927 4.26,2.063 true 6.49,0.927 6.688,2.323 true 6.229,0.917 6.031,2.229 true 6.76,1.333 6.875,1.583 true 4.104,1.135 4.333,1.188 true 5.979,0.917 5.365,2.01 true 1.604,1.24 2.073,0.99 true 0.781,2.167 1.135,1.698 true 1.333,2.25 1.354,1.698 true 1.896,2.188 1.563,1.708 true 6.844,1.594 7.156,1.792 0.313,0.198 10 false *1 5.104,2.073 5.604,2.281 0.5,0.208 10 false 1 (R-U) 6.146,0.25 6.542,0.417 0.396,0.167 10 false O1 5.823,2.313 6.323,2.521 0.5,0.208 10 false 2 (R-V) 6.438,2.354 6.938,2.563 0.5,0.208 10 false 3 (R-W) 3.354,0.25 3.75,0.417 0.396,0.167 10 false O2 4.417,1.156 4.729,1.354 0.313,0.198 10 false *1 4.198,2.156 4.698,2.365 0.5,0.208 10 false 3 (R-W) 3.375,2.25 3.875,2.458 0.5,0.208 10 false 2 (R-V) 2.552,1.906 3.052,2.115 0.5,0.208 10 false 1 (R-U) 1.281,0.26 1.677,0.427 0.396,0.167 10 false O3 2.125,0.875 2.438,1.073 0.313,0.198 10 false *1 0.563,2.208 0.885,2.406 0.323,0.198 10 false R-U 1.24,2.281 1.74,2.49 0.5,0.208 10 false R-V 1.75,2.229 2.25,2.438 0.5,0.208 10 false R-W 3.708,0.25 4.021,0.448 0.313,0.198 10 false *A 6.5,0.25 6.813,0.448 0.313,0.198 10 false *B 2.521,0.177 2.833,0.375 0.313,0.198 10 false *a
*A for LHD *B for RHD
*1 Shield Ground - -
*a NO. 2 Battery Pack Wire - -


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O2,O3)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

Click Connector(O3)Body>EV Battery Pack Wire>Shortcut Connector

O2-1 (R-U) or O3-1 (R-U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O2-2 (R-V) or O3-2 (R-V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O2-3 (R-W) or O3-3 (R-W) - Body ground and shield ground Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O1,O3)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

Click Connector(O3)Body>EV Battery Pack Wire>Shortcut Connector

O1-1 (R-U) or O3-1 (R-U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O1-2 (R-V) or O3-2 (R-V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
O1-3 (R-W) or O3-3 (R-W) - Body ground and shield ground Ignition switch off 10 MΩ or higher


NOTICE:

Wrap the terminal of the motor cable with insulating tape to prevent them from coming into contact with body ground.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O2,O3)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

Click Connector(O3)Body>EV Battery Pack Wire>Shortcut Connector

O2-1 (R-U) - O3-1 (R-U) Ignition switch off Below 1 Ω
O2-2 (R-V) - O3-2 (R-V) Ignition switch off Below 1 Ω
O2-3 (R-W) - O3-3 (R-W) Ignition switch off Below 1 Ω
O2-1 (R-U) - O3-2 (R-V) Ignition switch off 10 MΩ or higher
O2-2 (R-V) - O3-3 (R-W) Ignition switch off 10 MΩ or higher
O2-3 (R-W) - O3-1 (R-U) Ignition switch off 10 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(O1,O3)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

Click Connector(O3)Body>EV Battery Pack Wire>Shortcut Connector

O1-1 (R-U) - O3-1 (R-U) Ignition switch off Below 1 Ω
O1-2 (R-V) - O3-2 (R-V) Ignition switch off Below 1 Ω
O1-3 (R-W) - O3-3 (R-W) Ignition switch off Below 1 Ω
O1-1 (R-U) - O3-2 (R-V) Ignition switch off 10 MΩ or higher
O1-2 (R-V) - O3-3 (R-W) Ignition switch off 10 MΩ or higher
O1-3 (R-W) - O3-1 (R-U) Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 2 battery pack wire.



OK

5.INSPECT MOTOR CABLE

NG

REPLACE NO. 2 BATTERY PACK WIRE

5.INSPECT MOTOR CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.




Procedure1

a.
A481547C02
0.427,0.99 0.844,1.323 0.417,0.333 0.458,3.365 0.875,3.698 0.417,0.333 1.76,1.552 1.531,2 true 1.208,2.01 1.49,1.552 true 2.406,0.844 2.688,0.948 true 2.01,1.531 2.24,1.99 true 1.073,4.188 1.438,3.625 true 2.052,3.615 2.438,4.177 true 1.76,3.615 2.125,4.177 true 2.198,3.167 2.51,3.229 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.74,0.917 3.073,1.073 0.333,0.156 10 false *1 2.24,2.01 2.573,2.177 0.333,0.167 10 false U 1.458,2.031 1.792,2.198 0.333,0.167 10 false V 1.083,2.031 1.417,2.198 0.333,0.167 10 false W 0.604,3.469 0.917,3.667 0.313,0.198 10 false q2 0.583,1.073 0.896,1.271 0.313,0.198 10 false q1 2.427,4.198 2.76,4.365 0.333,0.167 10 false W 2.115,4.198 2.448,4.365 0.333,0.167 10 false V 1.021,4.198 1.354,4.365 0.333,0.167 10 false U 2.583,3.177 2.917,3.333 0.333,0.156 10 false *1
*1 Shield Ground
*a Motor Cable


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q1,q2)Location & Routing

Click Connector(q1)Body>Motor Cable>FCV Transaxle with Motor Assembly

Click Connector(q2)Body>Motor Cable>Shortcut Connector

q1-1 (W) or q2-3 (W) - Body ground and shield ground Ignition switch off 100 MΩ or higher
q1-2 (V) or q2-2 (V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
q1-3 (U) or q2-1 (U) - Body ground and shield ground Ignition switch off 100 MΩ or higher


NOTICE:

Wrap the terminal of the motor cable with insulating tape to prevent them from coming into contact with body ground.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q1,q2)Location & Routing

Click Connector(q1)Body>Motor Cable>FCV Transaxle with Motor Assembly

Click Connector(q2)Body>Motor Cable>Shortcut Connector

q1-1 (W) - q2-3 (W) Ignition switch off Below 1 Ω
q1-2 (V) - q2-2 (V) Ignition switch off Below 1 Ω
q1-3 (U) - q2-1 (U) Ignition switch off Below 1 Ω
q1-1 (W) - q2-2 (V) Ignition switch off 10 MΩ or higher
q1-2 (V) - q2-1 (U) Ignition switch off 10 MΩ or higher
q1-3 (U) - q2-3 (W) Ignition switch off 10 MΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the motor cable.



OK

NG