Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Shut Down Signal Circuit  


DESCRIPTION

The cause of the malfunction may be a shutdown signal.

Check whether there is a shutdown signal +B short circuit.

Related Parts Check
Area Inspection
HSDN terminal Check the HSDN signal line for an open or short circuit while READY OFF (ignition switch ON).
EV control ECU, inverter, wire harness Check for open or short circuit in EV control ECU, inverter and wire harness.

SYSTEM DESCRIPTION

Power supply to the motor is cut off due to a shutdown signal sent from the EV control ECU to the motor generator control ECU (MG ECU).

WIRING DIAGRAM

for LHD:
A480807E01
2.417,0.344 2.729,0.542 0.313,0.198 10 false 10 2.417,0.698 2.729,0.896 0.313,0.198 10 false 11 2.417,1.073 2.729,1.271 0.313,0.198 10 false 25 2.417,1.396 2.729,1.594 0.313,0.198 10 false 30 2.417,1.75 2.729,1.948 0.313,0.198 10 false 31 4.594,1.094 4.906,1.292 0.313,0.198 10 false 8 4.594,1.604 4.906,1.802 0.313,0.198 10 false 4 3.333,0.49 4.469,0.823 1.135,0.333 10 false From IGCT NO.4 Fuse 4.792,1.073 5.323,1.323 0.531,0.25 10 false HSDN 4.813,1.688 5.344,1.938 0.531,0.25 10 false E1 4.813,2.438 6.656,2.615 1.844,0.177 10 false EV Control ECU 1.948,1.083 2.479,1.333 0.531,0.25 10 false HSDN 2.052,0.792 2.583,1.042 0.531,0.25 10 false +B2 2.125,0.458 2.656,0.708 0.531,0.25 10 false +B 1.927,1.51 2.458,1.76 0.531,0.25 10 false GND1 1.927,1.844 2.458,2.094 0.531,0.25 10 false GND2 0.479,2.208 1,2.438 0.521,0.229 10 false A19 0.469,2.365 2.646,2.594 2.177,0.229 10 false Inverter with Converter Assembly 4.823,2.26 5.135,2.458 0.313,0.198 10 false A17

for RHD:
A480807E02
2.417,0.344 2.729,0.542 0.313,0.198 10 false 10 2.417,0.698 2.729,0.896 0.313,0.198 10 false 11 2.417,1.073 2.729,1.271 0.313,0.198 10 false 25 2.417,1.396 2.729,1.594 0.313,0.198 10 false 30 2.417,1.75 2.729,1.948 0.313,0.198 10 false 31 4.594,1.094 4.906,1.292 0.313,0.198 10 false 8 4.594,1.604 4.906,1.802 0.313,0.198 10 false 4 3.333,0.49 4.469,0.823 1.135,0.333 10 false From IGCT NO.4 Fuse 4.792,1.073 5.323,1.323 0.531,0.25 10 false HSDN 4.813,1.688 5.344,1.938 0.531,0.25 10 false E1 5.135,2.271 6.979,2.448 1.844,0.177 10 false EV Control ECU 1.948,1.083 2.479,1.333 0.531,0.25 10 false HSDN 2.052,0.792 2.583,1.042 0.531,0.25 10 false +B2 2.125,0.458 2.656,0.708 0.531,0.25 10 false +B 1.927,1.51 2.458,1.76 0.531,0.25 10 false GND1 1.927,1.844 2.458,2.094 0.531,0.25 10 false GND2 0.479,2.208 1,2.438 0.521,0.229 10 false A18 0.469,2.365 2.646,2.594 2.177,0.229 10 false Inverter with Converter Assembly 4.823,2.26 5.135,2.458 0.313,0.198 10 false A17

Refer to the wiring diagram for DTC P06881F.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK EV CONTROL ECU

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.
A478491C13
2.021,0.958 2.479,1.292 0.458,0.333 2.385,1.76 2.688,2.375 true 2.219,1.667 1.938,2.24 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 2.135,1.042 2.438,1.208 0.302,0.167 10 false A17 1.792,2.323 2.24,2.49 0.448,0.167 10 false E1 2.531,2.406 2.979,2.573 0.448,0.167 10 false HSDN
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-8 (HSDN) - A17-4 (E1) Ignition switch ON Below 4.5 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

SHUTDOWN SIGNAL CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

2.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


c.

Disconnect the A8*1 or D15*2 and A17 EV control ECU connectors.

*1: for LHD

*2: for RHD


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A480889C03
2.073,2.146 2.49,2.438 0.417,0.292 2.604,1.781 3.021,2.073 0.417,0.292 1.656,0.135 2.094,0.469 0.438,0.333 2.615,2.146 3.031,2.438 0.417,0.292 0.844,0.135 1.281,0.469 0.438,0.333 2.656,0.354 2.24,1.063 true 2.698,3.781 2.625,4.396 true 2.427,3.854 2.271,4.396 true 2.969,3.927 3.125,4.344 true 1.604,1.229 1.25,1.865 true 2.979,0.635 2.427,1.063 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.083,2 0.396,2.156 0.313,0.156 10 false *b 0.948,0.219 1.406,0.417 0.458,0.198 10 false A19 2.167,2.208 2.625,2.406 0.458,0.198 10 false A17 2.75,1.854 3.208,2.052 0.458,0.198 10 false A8 0.813,1.823 1.271,2.021 0.458,0.198 10 false HSDN 1.917,4.406 2.375,4.604 0.458,0.198 10 false HSDN 2.979,4.396 3.396,4.573 0.417,0.177 10 false MREL 2.552,4.406 3.01,4.604 0.458,0.198 10 false +B1 2.719,0.271 3.177,0.469 0.458,0.198 10 false +B 3.031,0.552 3.313,0.708 0.281,0.156 10 false +B2 1.76,0.219 2.219,0.417 0.458,0.198 10 false A18 1.354,0.208 1.667,0.406 0.313,0.198 10 false *A 2.135,0.229 2.448,0.427 0.313,0.198 10 false *B 2.719,2.208 3.177,2.406 0.458,0.198 10 false D15 3.083,1.813 3.396,2.01 0.313,0.198 10 false *A 3.094,2.208 3.406,2.406 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,A17)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A19-25 (HSDN) or A17-8 (HSDN) - Body ground Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18,A17)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A18-25 (HSDN) or A17-8 (HSDN) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the EV control ECU and inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for 2 minutes or more.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,A17,A8)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A19-25 (HSDN) - A19-10 (+B) Ignition switch off 10 kΩ or higher
A19-25 (HSDN) - A19-11 (+B2) Ignition switch off 10 kΩ or higher
A17-8 (HSDN) - A8-7 (+B1) Ignition switch off 10 kΩ or higher
A19-25 (HSDN) - A8-21 (MREL) Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18,A17,D15)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A18-25 (HSDN) - A18-10 (+B) Ignition switch off 10 kΩ or higher
A18-25 (HSDN) - A18-11 (+B2) Ignition switch off 10 kΩ or higher
A17-8 (HSDN) - D15-7 (+B1) Ignition switch off 10 kΩ or higher
A18-25 (HSDN) - D15-21 (MREL) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A8*1 or D15*2 and A17 EV control ECU connectors.

*1: for LHD

*2: for RHD


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

3.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
C256313C62
1.063,0.083 1.458,0.396 0.396,0.313 1.896,0.083 2.292,0.396 0.396,0.313 1.281,0.927 1.281,1.813 true 2.177,1.823 1.854,1.094 true 1.146,0.938 0.521,1.51 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 1.979,0.167 2.365,0.365 0.385,0.198 10 false A18 2.031,1.833 2.583,2.042 0.552,0.208 10 false HSDN 1.198,1.833 1.75,2.042 0.552,0.208 10 false +B 0.281,1.5 0.833,1.708 0.552,0.208 10 false +B2 1.51,0.156 1.823,0.354 0.313,0.198 10 false *A 1.146,0.156 1.531,0.354 0.385,0.198 10 false A19 2.333,0.156 2.646,0.354 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Component without harness connected
(Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-25 (HSDN) - A19-10 (+B) Ignition switch off 10 kΩ or higher
A19-25 (HSDN) - A19-11 (+B2) Ignition switch off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-25 (HSDN) - A18-10 (+B) Ignition switch off 10 kΩ or higher
A18-25 (HSDN) - A18-11 (+B2) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY