Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0C3000  Hybrid/EV Battery State of Charge High  


DESCRIPTION

The battery ECU assembly monitors the operation of the hybrid battery system and will store this DTC if it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0C3000 Hybrid/EV Battery State of Charge High Even though charging of the EV supply battery assembly is prohibited due to the SOC reaching the upper limit, charging continues to be performed due to a hybrid control system malfunction.
(1 trip detection logic)
·

EV control ECU

·

No. 1 EV battery junction block assembly


Master Warning:
Comes on
EV Battery A

Related Data List
DTC No. Data List
P0C3000
·

Hybrid/EV Battery SOC

·

WIN Control Limit Power

·

Hybrid/EV Battery Current



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Drive the vehicle on urban roads for approximately 10 minutes.

4.

Enter the following menus: Powertrain / EV battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398

Result:
Result Proceed to
Only P0C3000 is output A
P0C3000 and other DTCs are output B


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (EV)

B

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

2.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK FREEZE FRAME DATA (EV BATTERY)

B

3.CHECK FREEZE FRAME DATA (EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P0C3000.

Powertrain > EV Battery > DTC(P0C3000) > Freeze Frame Data
Tester Display
Ready Signal
SMRG Control Status
SMRB Control Status
SMRP Control Status
Hybrid/EV Battery Current
50040 398 44,23,25,27,289 P0C3000

Result:
Result Proceed to
OFF is displayed for "Ready Signal", "SMRP Control Status", "SMRB Control Status" and "SMRG Control Status" and -0.5 A or less is displayed for "Hybrid/EV Battery Current". A
Other than above B


HINT:

As the ignition switch ON state may cause the DTC to be stored, freeze frame data is used to judge the cause of the DTC output.


Post-procedure1

a.

Turn the ignition switch off.



A

4.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP, SMRB, SMRG)

B

4.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP, SMRB, SMRG)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper EV battery cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.

Disconnect the high voltage cable connectors from the No. 1 EV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479525C01
3.229,0.125 3.594,0.375 0.365,0.25 5.615,0.188 6.052,0.427 0.438,0.24 3.406,0.667 3.719,0.406 true 5.813,0.698 6.292,1.063 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.292,0.188 3.552,0.333 0.26,0.146 10 true N1 3.781,0.313 4.24,0.51 0.458,0.198 10 false CBI 5.719,0.208 6,0.396 0.281,0.188 10 true z13 6.375,1.031 6.531,1.229 0.156,0.198 10 false +
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance (SMRB):
Tester Connection Condition Specified Condition

Click Location & Routing(N1,z13)Location & Routing

Click Connector(N1)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

Click Connector(z13)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

N1-1 (CBI) - z13-1 (+) Always 10 kΩ or higher



b.

Measure the resistance according to the value(s) in the table below.

A479525C02
2.219,0.104 2.583,0.344 0.365,0.24 1.167,0.115 1.531,0.323 0.365,0.208 2.063,1.063 2.396,0.677 true 0.833,0.854 1.344,0.656 true 0.271,0.094 0.594,0.531 0.323,0.438 10 false *a 2.313,0.156 2.531,0.302 0.219,0.146 10 true N2 1.219,0.146 1.479,0.292 0.26,0.146 10 true z12 1.813,1 2.188,1.208 0.375,0.208 10 false CEI 0.719,0.781 0.875,0.979 0.156,0.198 10 false -
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance (SMRG, SMRP):
Tester Connection Condition Specified Condition

Click Location & Routing(N2,z12)Location & Routing

Click Connector(N2)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

Click Connector(z12)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

N2-1 (CEI) - z12-1 (-) Always 10 kΩ or higher


HINT:

If the resistance is between 24.3 and 29.7 Ω, it can be determined that SMRP is stuck closed.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the high voltage cable connectors to the No. 1 EV battery junction block assembly.


b.

Install the upper EV battery cover panel.



OK

5.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

NG

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

5.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

Pre-procedure1

a.

None.


Procedure1

a.

Turn the ignition switch to ON (READY).


b.

Perform a road test.

NOTICE:

Accelerate/decelerate gently. Avoid rapid acceleration/deceleration.



c.

Drive the vehicle with the value of Data List item "Hybrid/EV Battery Current" between -50 A and 50 A.

Powertrain > EV Battery > Data List
Tester Display
Hybrid/EV Battery Current
50003 398 289
HINT:

Distance and driving time are not specified.



d.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


e.

Check that the value of "Hybrid/EV Battery Current" is between - 0.5 A and 0.5 A with the ignition switch ON.

Powertrain > EV Battery > Data List
Tester Display
Hybrid/EV Battery Current
50003 398 289
NOTICE:
·

If the value is outside the specified range, perform the road test again.

·

This DTC may be output if Current Sensor Offset Learning has not been completed.



HINT:
·

If the ignition switch is ON and value of "Hybrid/EV Battery Current" is between - 0.5 A and 0.5 A, current sensor offset learning has been completed.

·

Even if the current sensor offset learning is not complete, the current sensor value will be corrected by repeating the road test a maximum of 7 times.




Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

END