Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  U115087  Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message  


DESCRIPTION

The battery ECU assembly transmits and receives signals via CAN communication to and from the EV control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
U115087 Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message The battery ECU assembly does not receive any signals from the EV control ECU for 1 second or more.
(1 trip detection logic)
·

Battery ECU assembly

·

EV control ECU

·

Wire harness or connector


Master Warning:
Comes on
EV Battery B

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
C374189E05
5.906,0.583 6.365,0.781 0.458,0.198 10 false +B1 5.917,1 6.375,1.198 0.458,0.198 10 false +B2 5.49,0.594 5.844,0.792 0.354,0.198 10 false A17 5.521,1 5.875,1.188 0.354,0.188 10 false A8 5.51,1.406 5.844,1.604 0.333,0.198 10 false A8 5.917,1.406 6.531,1.604 0.615,0.198 10 false MREL 2.521,1.781 3.375,1.99 0.854,0.208 10 false IGCT NO. 2 0.885,1.76 2.573,1.958 1.688,0.198 10 false R/B RR #2 1.5,1.188 2.354,1.396 0.854,0.208 10 false IGCT NO. 2 3.719,1.167 4.573,1.375 0.854,0.208 10 false PM-IGCT 1.615,0.885 1.771,1.083 0.156,0.198 10 false 1 2.01,0.885 2.167,1.083 0.156,0.198 10 false 2 4.146,0.885 4.302,1.083 0.156,0.198 10 false 2 3.792,0.875 3.948,1.073 0.156,0.198 10 false 1 3.198,1.292 3.469,1.479 0.271,0.188 10 false 2 2.438,1.292 2.729,1.5 0.292,0.208 10 false 1 3.208,0.896 3.365,1.094 0.156,0.198 10 false 5 2.427,0.885 2.583,1.083 0.156,0.198 10 false 3 0.927,2.51 2.125,2.771 1.198,0.26 10 false Auxiliary Battery 0.542,4.906 2.26,5.125 1.719,0.219 10 false Battery ECU Assembly 0.271,4.906 0.583,5.104 0.313,0.198 10 false z26 0.271,7.083 0.615,7.281 0.344,0.198 10 false D92 2.792,3.708 3.406,3.906 0.615,0.198 10 false CA1H 3.302,3.708 3.917,3.906 0.615,0.198 10 false CA1H 2.792,4.479 3.406,4.677 0.615,0.198 10 false CA1L 3.323,4.479 3.938,4.677 0.615,0.198 10 false CA1L 5.885,4.385 6.5,4.583 0.615,0.198 10 false CA4L 5.885,3.792 6.5,3.99 0.615,0.198 10 false CA4H 5.531,3.781 5.885,3.979 0.354,0.198 10 false A8 5.531,4.365 5.875,4.563 0.344,0.198 10 false A8 2.719,4.917 4.167,5.25 1.448,0.333 10 false No. 2 EV Battery Pack Wire Connector 2.302,4.917 2.833,5.135 0.531,0.219 10 false G156 0.625,7.083 2.917,7.281 2.292,0.198 10 false Shift Control ECU 1.313,3.813 1.927,4.01 0.615,0.198 10 false CA1H 1.333,4.375 1.948,4.573 0.615,0.198 10 false CA1L 1.792,3.615 2.104,3.813 0.313,0.198 10 false 16 1.792,4.208 2.104,4.406 0.313,0.198 10 false 15 2.531,3.604 2.688,3.802 0.156,0.198 10 false 4 2.469,4.219 2.781,4.417 0.313,0.198 10 false 13 3.802,3.615 3.958,3.813 0.156,0.198 10 false 4 3.771,4.219 4.083,4.417 0.313,0.198 10 false 13 5.781,4.906 6.885,5.542 1.104,0.635 10 false EV Control ECU 1.292,6.615 1.906,6.813 0.615,0.198 10 false CA2L 1.281,6.01 1.896,6.208 0.615,0.198 10 false CA2H 0.531,7.521 2.448,7.75 1.917,0.229 10 false : CAN Communication Line 1.802,5.802 1.958,6 0.156,0.198 10 false 6 1.802,6.396 1.958,6.594 0.156,0.198 10 false 5 5.583,0.354 5.74,0.552 0.156,0.198 10 false 1 5.573,0.802 5.729,1 0.156,0.198 10 false 7 5.531,1.208 5.875,1.417 0.344,0.208 10 false 21 5.583,3.552 5.896,3.75 0.313,0.198 10 false 2 5.594,4.146 5.906,4.344 0.313,0.198 10 false 3

for RHD:
C374189E06
5.906,0.583 6.365,0.781 0.458,0.198 10 false +B1 5.917,1 6.375,1.198 0.458,0.198 10 false +B2 5.49,0.594 5.844,0.792 0.354,0.198 10 false A17 5.49,1 5.844,1.188 0.354,0.188 10 false D15 5.49,1.406 5.823,1.604 0.333,0.198 10 false D15 5.917,1.406 6.531,1.604 0.615,0.198 10 false MREL 2.521,1.781 3.375,1.99 0.854,0.208 10 false IGCT NO. 2 0.885,1.76 2.573,1.958 1.688,0.198 10 false R/B RR #2 1.479,1.188 2.333,1.396 0.854,0.208 10 false IGCT NO. 2 3.719,1.167 4.573,1.375 0.854,0.208 10 false PM-IGCT 1.615,0.885 1.771,1.083 0.156,0.198 10 false 1 2.01,0.885 2.167,1.083 0.156,0.198 10 false 2 4.146,0.885 4.302,1.083 0.156,0.198 10 false 2 3.792,0.875 3.948,1.073 0.156,0.198 10 false 1 3.198,1.292 3.469,1.479 0.271,0.188 10 false 2 2.438,1.292 2.729,1.5 0.292,0.208 10 false 1 3.208,0.896 3.365,1.094 0.156,0.198 10 false 5 2.427,0.885 2.583,1.083 0.156,0.198 10 false 3 0.927,2.51 2.125,2.771 1.198,0.26 10 false Auxiliary Battery 0.542,4.906 2.26,5.125 1.719,0.219 10 false Battery ECU Assembly 0.271,4.906 0.583,5.104 0.313,0.198 10 false z26 0.271,7.083 0.615,7.281 0.344,0.198 10 false D92 2.792,3.708 3.406,3.906 0.615,0.198 10 false CA1H 3.302,3.708 3.917,3.906 0.615,0.198 10 false CA1H 2.792,4.479 3.406,4.677 0.615,0.198 10 false CA1L 3.323,4.479 3.938,4.677 0.615,0.198 10 false CA1L 5.885,4.385 6.5,4.583 0.615,0.198 10 false CA4L 5.885,3.792 6.5,3.99 0.615,0.198 10 false CA4H 5.51,3.781 5.865,3.979 0.354,0.198 10 false D15 5.49,4.365 5.833,4.563 0.344,0.198 10 false D15 2.719,4.917 4.167,5.25 1.448,0.333 10 false No. 2 EV Battery Pack Wire Connector 2.302,4.917 2.833,5.135 0.531,0.219 10 false G156 0.625,7.083 2.917,7.281 2.292,0.198 10 false Shift Control ECU 1.313,3.813 1.927,4.01 0.615,0.198 10 false CA1H 1.333,4.375 1.948,4.573 0.615,0.198 10 false CA1L 1.792,3.615 2.104,3.813 0.313,0.198 10 false 16 1.792,4.208 2.104,4.406 0.313,0.198 10 false 15 2.531,3.604 2.688,3.802 0.156,0.198 10 false 4 2.469,4.219 2.781,4.417 0.313,0.198 10 false 13 3.802,3.615 3.958,3.813 0.156,0.198 10 false 4 3.771,4.219 4.083,4.417 0.313,0.198 10 false 13 5.781,4.906 6.865,5.427 1.083,0.521 10 false EV Control ECU 1.292,6.615 1.906,6.813 0.615,0.198 10 false CA2L 1.281,6.01 1.896,6.208 0.615,0.198 10 false CA2H 0.531,7.521 2.448,7.75 1.917,0.229 10 false : CAN Communication Line 1.802,5.802 1.958,6 0.156,0.198 10 false 6 1.802,6.396 1.958,6.594 0.156,0.198 10 false 5 5.583,0.354 5.74,0.552 0.156,0.198 10 false 1 5.573,0.802 5.729,1 0.156,0.198 10 false 7 5.531,1.208 5.875,1.417 0.344,0.208 10 false 21 5.583,3.552 5.896,3.75 0.313,0.198 10 false 2 5.594,4.146 5.906,4.344 0.313,0.198 10 false 3

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


Post-procedure1

a.

Turn the ignition switch off.



A

2.CONFIRM MODEL

B

2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

3.CHECK EV CONTROL ECU (VOLTAGE)

B

7.CHECK EV CONTROL ECU (VOLTAGE)
3.CHECK EV CONTROL ECU (VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.
A478491C28
2.031,1.01 2.406,1.26 0.375,0.25 2.594,1.01 2.969,1.26 0.375,0.25 1.938,2.604 2.417,1.667 true 2.99,2.583 2.625,1.677 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.813,2.646 2.333,2.833 0.521,0.188 10 false +B1 2.885,2.646 3.344,2.823 0.458,0.177 10 false +B2 2.094,1.073 2.469,1.25 0.375,0.177 10 false A17 2.698,1.063 3.104,1.229 0.406,0.167 10 false A8
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,A8)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-1 (+B1) - Body ground Ignition switch ON 11 to 14 V
A8-7 (+B2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C374188C21
1.531,0.24 1.969,0.469 0.438,0.229 0.677,1.802 1.594,1.385 true 0.677,0.646 1.594,1.115 true 0.25,0.573 0.865,0.771 0.615,0.198 10 false CA1H 0.26,1.781 0.875,1.979 0.615,0.198 10 false CA1L 1.594,0.281 2.052,0.479 0.458,0.198 10 false G156 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-4 (CA1H) - G156-13 (CA1L) Ignition switch off 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G156 No. 2 EV battery pack wire connector.


b.

Install the center No. 2 floor to brace extension.



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)

NG

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C374185C48
1.521,1.656 1.969,1.938 0.448,0.281 1.49,0.063 1.958,0.323 0.469,0.26 1.052,2.417 0.531,1.875 true 1.177,2.438 1.021,1.823 true 1.896,0.813 2.729,0.344 true 1.885,1.104 2.698,1.427 true 1.646,1.729 1.958,1.927 0.313,0.198 10 false z26 1.573,0.135 2.031,0.333 0.458,0.198 10 false G156 0.313,1.698 0.927,1.896 0.615,0.198 10 false CA1H 2.781,0.25 3.396,0.448 0.615,0.198 10 false CA1H 0.854,1.635 1.469,1.833 0.615,0.198 10 false CA1L 2.75,1.365 3.365,1.563 0.615,0.198 10 false CA1L 0.156,0.146 0.469,0.302 0.313,0.156 10 false *a 0.135,1.521 0.448,1.677 0.313,0.156 10 false *b
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26,G156)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

z26-16 (CA1H) - G156-4 (CA1H) Always Below 1 Ω
z26-15 (CA1L) - G156-13 (CA1L) Always Below 1 Ω
z26-16 (CA1H) or G156-4 (CA1H) - Body ground and other terminals Always 10 kΩ or higher
z26-15 (CA1L) or G156-13 (CA1L) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A8 EV control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the EV control ECU and battery ECU assembly is not loose or disconnected.




c.

Disconnect the D92 shift control ECU connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



e.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
A479529C02
1.521,0.281 2.063,0.625 0.542,0.344 2.521,1.979 2.969,2.292 0.448,0.313 0.771,0.75 1.688,1.188 true 0.792,1.656 1.688,1.365 true 2.573,4.344 3,3.615 true 2.292,4 2.927,3.615 true 1.615,0.375 2.229,0.573 0.615,0.198 10 false G156 0.375,0.677 0.99,0.875 0.615,0.198 10 false CA1H 0.375,1.583 0.99,1.781 0.615,0.198 10 false CA1L 2.656,2.052 3.063,2.25 0.406,0.198 10 false A8 2.375,4.385 2.99,4.583 0.615,0.198 10 false CA4H 2.125,4.042 2.74,4.24 0.615,0.198 10 false CA4L 0.135,0.177 0.448,0.375 0.313,0.198 10 false *a 0.146,1.979 0.458,2.177 0.313,0.198 10 false *b
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,A8)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G156-4 (CA1H) - A8-2 (CA4H) Ignition switch off Below 1 Ω
G156-13 (CA1L) - A8-3 (CA4L) Ignition switch off Below 1 Ω
G156-4 (CA1H) or A8-2 (CA4H) - Other terminals and body ground Ignition switch off 10 kΩ or higher
G156-13 (CA1L) or A8-3 (CA4L) - Other terminals and body ground Ignition switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery ECU assembly and EV control ECU is not loose or disconnected and its terminals are not deformed or corroded.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G156 No. 2 EV battery pack wire connector.


b.

Install the center No. 2 floor to brace extension.


c.

Reconnect the D92 shift control ECU connector.


d.

Reconnect the A8 EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK EV CONTROL ECU (VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.
A478491C10
2.031,1.01 2.406,1.26 0.375,0.25 2.594,1.01 2.969,1.26 0.375,0.25 1.938,2.604 2.417,1.667 true 2.99,2.583 2.625,1.677 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 1.813,2.646 2.333,2.833 0.521,0.188 10 false +B1 2.885,2.646 3.344,2.823 0.458,0.177 10 false +B2 2.094,1.073 2.469,1.25 0.375,0.177 10 false A17 2.656,1.063 3.063,1.229 0.406,0.167 10 false D15
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,D15)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

A17-1 (+B1) - Body ground Ignition switch ON 11 to 14 V
D15-7 (+B2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C374188C21
1.531,0.24 1.969,0.469 0.438,0.229 0.677,1.802 1.594,1.385 true 0.677,0.646 1.594,1.115 true 0.25,0.573 0.865,0.771 0.615,0.198 10 false CA1H 0.26,1.781 0.875,1.979 0.615,0.198 10 false CA1L 1.594,0.281 2.052,0.479 0.458,0.198 10 false G156 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-4 (CA1H) - G156-13 (CA1L) Ignition switch off 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G156 No. 2 EV battery pack wire connector.


b.

Install the center No. 2 floor to brace extension.



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)

NG

10.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
9.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307N11
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C374185C48
1.521,1.656 1.969,1.938 0.448,0.281 1.49,0.063 1.958,0.323 0.469,0.26 1.052,2.417 0.531,1.875 true 1.177,2.438 1.021,1.823 true 1.896,0.813 2.729,0.344 true 1.885,1.104 2.698,1.427 true 1.646,1.729 1.958,1.927 0.313,0.198 10 false z26 1.573,0.135 2.031,0.333 0.458,0.198 10 false G156 0.313,1.698 0.927,1.896 0.615,0.198 10 false CA1H 2.781,0.25 3.396,0.448 0.615,0.198 10 false CA1H 0.854,1.635 1.469,1.833 0.615,0.198 10 false CA1L 2.75,1.365 3.365,1.563 0.615,0.198 10 false CA1L 0.156,0.146 0.469,0.302 0.313,0.156 10 false *a 0.135,1.521 0.448,1.677 0.313,0.156 10 false *b
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26,G156)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

z26-16 (CA1H) - G156-4 (CA1H) Always Below 1 Ω
z26-15 (CA1L) - G156-13 (CA1L) Always Below 1 Ω
z26-16 (CA1H) or G156-4 (CA1H) - Body ground and other terminals Always 10 kΩ or higher
z26-15 (CA1L) or G156-13 (CA1L) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D15 EV control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the EV control ECU and battery ECU assembly is not loose or disconnected.




c.

Disconnect the D92 shift control ECU connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the center No. 2 floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



e.
C382281N05
2.688,0.25 3.146,0.479 0.458,0.229 2.74,0.281 3.115,0.448 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
A479529C01
1.521,0.281 2.063,0.625 0.542,0.344 2.521,1.979 2.969,2.292 0.448,0.313 0.771,0.75 1.688,1.188 true 0.792,1.656 1.688,1.365 true 2.573,4.344 3,3.615 true 2.292,4 2.927,3.615 true 1.615,0.375 2.229,0.573 0.615,0.198 10 false G156 0.375,0.677 0.99,0.875 0.615,0.198 10 false CA1H 0.375,1.583 0.99,1.781 0.615,0.198 10 false CA1L 2.615,2.052 3.021,2.25 0.406,0.198 10 false D15 2.375,4.385 2.99,4.583 0.615,0.198 10 false CA4H 2.125,4.042 2.74,4.24 0.615,0.198 10 false CA4L 0.135,0.177 0.448,0.375 0.313,0.198 10 false *a 0.146,1.979 0.458,2.177 0.313,0.198 10 false *b
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,D15)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

G156-4 (CA1H) - D15-2 (CA4H) Ignition switch off Below 1 Ω
G156-13 (CA1L) - D15-3 (CA4L) Ignition switch off Below 1 Ω
G156-4 (CA1H) or D15-2 (CA4H) - Other terminals and body ground Ignition switch off 10 kΩ or higher
G156-13 (CA1L) or D15-3 (CA4L) - Other terminals and body ground Ignition switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery ECU assembly and EV control ECU is not loose or disconnected and its terminals are not deformed or corroded.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G156 No. 2 EV battery pack wire connector.


b.

Install the center No. 2 floor to brace extension.


c.

Reconnect the D92 shift control ECU connector.


d.

Reconnect the D15 EV control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR