Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › from 2021.08
RM37H0E _55 Steering _095770 STEERING COLUMN _0449635 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  INSTALLATION  


CAUTION / NOTICE / HINT

C449474N01
3.167,1.813 4,1.979 0.833,0.167 3.083,1.729 4.083,2.063 1,0.333 5.51,1.76 5.74,1.406 5.74,1.406 5.906,1.406 true 4.24,0.479 4.438,0.948 4.438,0.948 4.604,0.948 true 6.635,0.167 6.885,0.167 false 2.823,1.896 3.167,1.896 false 6.458,0.063 7.01,0.417 0.552,0.354 18 false 1 6,1.292 6.552,1.646 0.552,0.354 18 false 3 3.229,1.823 4.208,1.99 0.979,0.167 8 false 35.3 (360, 26) 4.865,0.833 5.188,1.146 0.323,0.313 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - - - -
2 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -
3 FRONT WHEEL LH - - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

C447790N02
1,1.667 1.833,1.833 0.833,0.167 3.667,0.135 4.417,0.302 0.75,0.167 2.417,1.917 3.167,2.083 0.75,0.167 2.417,4.417 3.5,4.583 1.083,0.167 2.333,1.833 3.25,2.167 0.917,0.333 0.917,1.583 1.917,1.917 1,0.333 3.583,0.052 4.5,0.385 0.917,0.333 4.5,5.063 4.667,5.375 4.667,5.375 4.833,5.375 true 4.521,3.844 4.635,4.042 4.635,4.042 4.802,4.042 true 4.104,0.885 4.167,0.583 4.167,0.583 4.333,0.583 true 4.833,2.583 5,2.896 5,2.896 5.167,2.896 true 0.958,1.281 1.125,1.281 1.125,1.281 1.292,1.031 true 1.833,1.75 2.063,1.75 2.063,1.75 2.063,1.531 true 3.438,0.219 3.667,0.219 true 3.167,2 3.385,2 3.385,2 3.385,1.833 true 3.969,4.333 3.969,4.5 3.969,4.5 3.5,4.5 true 4.938,5.25 5.219,5.604 0.281,0.354 18 false 7 4.885,3.896 5.281,4.219 0.396,0.323 18 false 6 5.229,2.771 5.583,3.167 0.354,0.396 18 false 5 0.75,1.188 1.052,1.427 0.302,0.24 10 false *1 4.719,0.396 5.083,0.75 0.365,0.354 18 false 4 4.156,3.094 4.469,3.292 0.313,0.198 10 false x 2 3.531,1.698 3.844,1.896 0.313,0.198 10 false x 2 1.063,1.677 2.063,1.844 1,0.167 8 false 35.3 (360, 26) 3.74,0.146 4.51,0.313 0.771,0.167 8 false 36 (367, 27) 2.49,1.927 3.406,2.094 0.917,0.167 8 false 36 (367, 27) 2.49,4.427 3.573,4.594 1.083,0.167 8 false 9.8 (100, 87 in.*lbf) 4.094,4.208 4.5,4.417 0.406,0.208 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

4 STEERING COLUMN ASSEMBLY 45250 (Click here) - -
5 NO. 2 HEATER TO REGISTER DUCT 55844 - - -
6 AIR DUCT SUB-ASSEMBLY - - - -
7 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -

*1 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque

C449476N01
4.271,1.25 4.083,1.25 4.083,1.25 3.844,0.917 true 5,3.865 5.448,3.865 true 4.667,2.375 5.188,2.375 true 5.563,3.729 5.958,4.094 0.396,0.365 18 false 10 4.365,1.125 4.656,1.479 0.292,0.354 18 false 9 5.552,2.271 5.948,2.635 0.396,0.365 18 false 8 5.781,3.281 6.094,3.479 0.313,0.198 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

8 TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY - (Click here) - -
9 UPPER STEERING COLUMN COVER 45286B - - -
10 LOWER STEERING COLUMN COVER 45287 - - -

C449473N01
5.219,2.333 5.635,2.333 true 6.521,0.25 6.813,0.25 true 6.51,0.688 6.802,0.688 true 5.354,0.125 6.563,0.417 1.208,0.292 18 false 11, 12, 14 5.729,2.188 6.271,2.552 0.542,0.365 18 false 13 6.198,0.563 6.552,0.865 0.354,0.302 18 false 15

Procedure Part Name Code
Z101186

Z101188

Z101187

11 ALIGN FRONT WHEELS FACING STRAIGHT AHEAD - - - -
12 INSPECT AND ADJUST SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY 84306 (Click here)
13 STEERING WHEEL ASSEMBLY 45100 - - -
14 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -
15 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)
16 PERFORM INITIALIZATION - - - (Click here)

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45260 2.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C447804C01
2,1.417 1.875,1.063 true 2.167,1.417 2,1.417 2,1.417 1.833,1.104 true 2.271,1.313 2.479,1.531 0.208,0.219 10 true *a 3.75,0.083 4,0.417 0.25,0.333 18 false ii 0.396,0.031 0.698,0.313 0.302,0.281 18 false i 1.833,2.083 2.083,2.417 0.25,0.333 18 false iii
*a Matchmark - -


i.

Install the No. 2 steering intermediate shaft assembly to the rack and pinion power steering gear assembly.


ii.

Install the bolt.

Torque:
35.3 N*m (360 kgf*cm, 26 ft.*lbf)


iii.

Tighten the clamp.



Hide 3.INSTALL FRONT WHEEL LH

Hide 45250 4.INSTALL STEERING COLUMN ASSEMBLY

a.
C447805C02
1.24,0.448 1.073,0.875 1.073,0.875 1.344,0.49 true 0.938,0.906 1.167,1.104 0.229,0.198 10 true *a 0.406,0.052 0.625,0.354 0.219,0.302 18 true i 3.792,0 4.01,0.302 0.219,0.302 18 true ii 0.24,2.146 0.521,2.458 0.281,0.313 18 true iii 3.792,2.042 4.073,2.354 0.281,0.313 18 true iv
*a Matchmark - -


i.

Install the steering column assembly to the No. 2 steering intermediate shaft assembly.


ii.

Install the steering column assembly with the 2 nuts and bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Temporarily tighten the bolt, and then fully tighten the bolt and 2 nuts in the order of 2 nuts and bolt.



iii.

Install the bolt.

Torque:
35.3 N*m (360 kgf*cm, 26 ft.*lbf)


iv.

Connect each connector and engage each wire harness clamp to the steering column assembly.



Hide 55844 5.INSTALL NO. 2 HEATER TO REGISTER DUCT

Hide 6.INSTALL AIR DUCT SUB-ASSEMBLY

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

Hide 73900 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 8.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.




a.
C446728C01
0.313,0.208 0.594,0.563 0.281,0.354 18 false i 3.76,0.146 4.344,0.469 0.583,0.323 18 false ii, iii 1.844,3.031 2.104,3.385 0.26,0.354 18 false iv
V113147

Install in this Direction - -


i.

Using pliers, support the band clamp while loosened and set the turn signal switch assembly with spiral cable sub-assembly.


ii.

Engage the claw to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly as shown in the illustration.


iii.

Tighten the band clamp.


iv.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.



Hide 45286B 9.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 10.INSTALL LOWER STEERING COLUMN COVER

Hide 84306 12.INSPECT AND ADJUST SPIRAL CABLE SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 45100 13.INSTALL STEERING WHEEL ASSEMBLY

Hide 14. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Z101186

HINT:

Return the customization settings to the settings before changing them.




Hide 15. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART