Home › ENGINE › 1NZ-FXE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

for Preparation Click here


DESCRIPTION

When a misfire occurs in the engine, hydrocarbons (HC) enter the exhaust gas in high concentrations. If this HC concentration is high enough, there could be an increase in exhaust emissions levels. High concentrations of HC can also increase the temperature of the catalyst, possibly damaging the catalyst. To prevent this increase in emissions and limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the catalyst reaches a point of thermal degradation, the ECM will blink the MIL. For monitoring misfire, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. The misfire counter increments when crankshaft rotation speed variations exceed threshold values.
If the misfiring rate exceeds the threshold value and could cause emissions deterioration, the ECM illuminates the MIL.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Misfiring of random cylinders is detected during any particular 200 or 1,000 revolutions
1 trip detection logic: MIL blinks
2 trip detection logic: MIL illuminates
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connection
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV hose connection
  13. PCV hose
  14. ECM
P0301
P0302
P0303
P0304
  1. For any particular 200 revolutions of engine, misfiring is detected which can cause catalyst overheating (This causes MIL to blink)
  2. For any particular 1,000 revolutions of engine, misfiring is detected which causes a deterioration in emissions (2 trip detection logic)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connection
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV hose connection
  13. PCV hose
  14. ECM

NOTICE:
When several codes for a misfiring cylinder are recorded repeatedly but no random misfire code is recorded, it indicates that the misfires have been detected and recorded at different times.

Reference: Inspection using oscilloscope
With the engine idling, check the waveform between terminals #10 to #40 and E01 of the ECM connectors.

HINT:
The correct waveform is as shown.


A078423E05


MONITOR DESCRIPTION


A083872E03

The ECM illuminates the MIL (2 trip detection logic) if:
  1. The percent misfire exceeds the specified limit per 1,000 engine revolutions. One occurrence of excessive misfire during engine start will illuminate the MIL. After engine start, four occurrences of excessive misfire will illuminate the MIL.
The ECM blinks the MIL (immediately) if:
  1. The threshold for percent of misfire causing catalyst damage is reached 1 time per 200 engine revolutions at a high rpm, and 3 times in 200 engine revolutions at a normal rpm.
  2. The threshold for percent of misfire causing catalyst damage is reached.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
Required Sensors/Components (Main)
Crankshaft position sensor and camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature and intake air temperature sensors and mass air flow meter
Frequency of Operation
Continuous
Duration
1,000 to 4,000 crankshaft revolutions: Emission related misfire
200 to 600 crankshaft revolutions: Catalyst damaging misfire
MIL Operation
2 driving cycles: Emission related misfire
MIL flashes immediately: Catalyst damaging misfire
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
Monitor will not run if the following DTCs are present
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)
P0120 - P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for Closed Loop)
P0325- P0328 (Knock sensor)
P0335 (CKP sensor)
P0340, P0341(CMP sensor)
P0500 (VSS)
Battery voltage
8 V or more
Throttle position learning
Completed
VVT system
Not operated by scan tool
Engine RPM
850 to 5300 rpm
Both of the following conditions 1 and 2 are met
-
1. ECT
-10°C (14°F) or more
2. Either of following conditions (a) or (b) met
-
(a) ECT at engine start
More than -7°C (19°F)
(b) ECT
More than 20°C (68°F)
Fuel cut
OFF

Monitor period of emission-related misfire: 
First 1,000 revolutions after engine start, or check mode
Crankshaft 1,000 revolutions
Except above
Crankshaft 1,000 revolutions x 4

Monitor period of catalyst-damaging misfire (MIL blinks): 
All of following conditions 1, 2 and 3 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
3. Engine RPM
Less than 3400 rpm
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor period of emission-related misfire: 
Misfire rate
2% or more

Monitor period of catalyst-damaging misfire (MIL blinks): 
Number of misfire per 200 revolutions
108 or more (varies with intake air amount and RPM)

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM


A151890E02


CONFIRMATION DRIVING PATTERN

  1. Connect Techstream to the DLC3.
  2. Turn the power switch ON (IG).
  3. Turn the tester on.
  4. Record the DTC(s) and freeze frame data.
  5. Using the tester, switch the ECM (included in the hybrid vehicle control ECU) from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (CYL #1 to #4) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as an engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below, with the MISFIRE RPM and MISFIRE LOAD in the Data List.

    Engine RPM
    Duration
    Idling
    3.5 minutes or more
    1,000
    3 minutes or more
    2,000
    1.5 minutes or more
    3,000
    1 minute or more

  8. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the power switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the power switch off and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
    4. The problem is complex due to multiple factors.
  5. After finishing repairs, check that no misfires occur in each cylinder (CYL #1, #2, #3 and #4).
  6. Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern after the repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not set specific misfiring cylinder DTCs at a high engine RPM. If misfires only occur during high engine RPM driving, only DTC P0300 is set.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the tester.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not set.
  8. When either SHORT FT #1 or LONG FT #1 in the freeze frame data is outside the range of +-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).
  9. When the COOLANT TEMP in the freeze frame data is less than 75°C (167°F), misfires occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel which causes vibration may cause misfire DTCs to be detected.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0300, P0301, P0302, P0303 and/or P0304
    A
    P0300, P0301, P0302, P0303 and/or P0304 and other DTCs
    B

    HINT:
    If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.

  1. Read and note the MISFIRE RPM and MISFIRE LOAD (engine load) values.

    HINT:
    The MISFIRE RPM and MISFIRE LOAD values indicate the vehicle conditions under which the misfire occurred.


NEXT


3.CHECK PCV HOSE (HOSE CONNECTIONS)

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4.CHECK MISFIRE COUNT (CYL #1, #2, #3 AND #4)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Rate, #2, #3 and #4.

  1. Put the engine in inspection mode (Click here).

  1. Read each value for CYL #1 to #4 displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Shift the shift selector lever to the D position.

    2. Check CYL #1 to #4.

    3. If misfire counts are still not displayed, perform the following two steps and then check the misfire counts again.

  1. Drive the vehicle with the MISFIRE RPM and MISFIRE LOAD noted in the "READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)" procedures above.

  1. Read the CYL #1 to #4 or DTCs displayed on the tester.

    Result:

    Misfire Count
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item, MISFIRE MARGIN. Try to find vehicle driving conditions that lower the MISFIRE MARGIN value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the ECT is below 75°C (167°F), it may only be possible to detect the misfire when the engine is cold.
    3. If the freeze frame data's record of the ENGINE RUN TIME is below 120 seconds, misfire may be detected immediately after the engine is started.



B
Go to step 17
A


5.CHECK SPARK PLUG


    B002101E03
  1. Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Standard gap:
    0.7 to 0.8 mm (0.028 to 0.032 in.)

    Maximum electrode gap:
    1.16 mm (0.046 in.)

  1. Check the electrode for carbon deposits.
    Recommended spark plug: 
    Manufacturers
    Products
    DENSO
    SK16R11

    NOTICE:
    If the electrode gap is larger than the standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG
OK


6.CHECK FOR SPARK AND IGNITION
  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Fuel Cut All.

  1. Touch the spark plug tip to the cylinder head.

  1. Perform the Fuel Cut All operation (press the RIGHT or LEFT button to change to ON).

    NOTICE:
    When Fuel Cut All is OFF and the engine is cranked, fuel injection will occur.

  1. Crank the engine for less than 2 seconds and check for spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.



NG
Go to step 29
OK


7.CHECK CYLINDER COMPRESSION PRESSURE (MISFIRING CYLINDER)
  1. Measure the cylinder compression pressure of the misfiring cylinder.



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


8.INSPECT ECM TERMINAL VOLTAGE (MISFIRING CYLINDER)


    A124045E06
  1. Turn the power switch ON (IG).

  1. Measure the voltage between the terminals of the ECM connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    E4-2 (#10) - E4-7 (E01)
    9 to 14 V
    E4-3 (#20) - E4-7 (E01)
    9 to 14 V
    E4-4 (#30) - E4-7 (E01)
    9 to 14 V
    E4-5 (#40) - E4-7 (E01)
    9 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (INJECTOR - HYBRID VEHICLE CONTROL ECU)


    A180469E01
  1. Disconnect the injector connector (of the misfiring cylinder).

  1. Disconnect the E4 ECM connector.

  1. Turn the power switch ON (IG).

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connections
    Specified Conditions
    No. 1
    I5-1 - Ground
    9 to 14 V
    No. 2
    I6-1 - Ground
    9 to 14 V
    No. 3
    I7-1 - Ground
    9 to 14 V
    No. 4
    I8-1 - Ground
    9 to 14 V

    Standard resistance:
    Cylinder
    Tester Connections
    Specified Conditions
    No. 1
    I5-2 - Ground
    10 kΩ or higher
    I5-2 - E4-2 (#10)
    Below 1 Ω
    No. 2
    I6-2 - Ground
    10 kΩ or higher
    I6-2 - E4-3 (#20)
    Below 1 Ω
    No. 3
    I7-2 - Ground
    10 kΩ or higher
    I7-2 - E4-4 (#30)
    Below 1 Ω
    No. 4
    I8-2 - Ground
    10 kΩ or higher
    I8-2 - E4-5 (#40)
    Below 1 Ω

  1. Reconnect the injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK FUEL INJECTOR ASSEMBLY (MISFIRING CYLINDER)
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


11.CHECK VALVE CLEARANCE (MISFIRING CYLINDER)


NG
ADJUST VALVE CLEARANCE
OK


12.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


13.CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE OR FILTER
OK


14.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

  1. Measure the coolant temperature using a thermometer and compare the value with the value displayed on Techstream.

    Temperature value:
    Almost same as the actual engine coolant temperature.

    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F)
    B
    OK (Same as actual engine coolant temperature)
    C

    HINT:
    1. If there is an open circuit, Techstream indicates -40°C (-40°F).
    2. If there is a short circuit, Techstream indicates 140°C (284°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


15.READ VALUE USING TECHSTREAM (MAF)
  1. Connect Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

  1. Read its value using Techstream.

    Result:
    Air Flow Rate (g/sec.)
    Proceed to
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0 (*)
    C

    HINT:
    *: The value must be changed when the throttle valve is opened or closed.



NG
REPLACE MASS AIR FLOW METER
OK


16.CHECK VALVE TIMING


NG
ADJUST VALVE TIMING
OK

REPLACE ECM 

17.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


18.CHECK FUEL PRESSURE
  1. Check the fuel pressure.



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE OR FILTER
OK


19.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG).

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

  1. Measure the coolant temperature using a thermometer and compare the value with the value displayed on Techstream.

    Temperature value:
    Almost same as the actual engine coolant temperature.

    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F)
    B
    OK (Same as actual engine coolant temperature)
    C

    HINT:
    1. If there is an open circuit, Techstream indicates -40°C (-40°F).
    2. If there is a short circuit, Techstream indicates 140°C (284°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


20.READ VALUE USING TECHSTREAM (MAF)
  1. Connect Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Turn Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

  1. Read its value using Techstream.

    Result:
    Air Flow Rate (g/sec.)
    Proceed to
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0 (*)
    C

    HINT:
    *: The value must be changed when the throttle valve is opened or closed.



NG
REPLACE MASS AIR FLOW METER
OK


21.CHECK SPARK PLUG


    B002101E03
  1. Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Standard gap:
    0.7 to 0.8 mm (0.028 to 0.032 in.)

    Maximum electrode gap:
    1.16 mm (0.046 in.)

  1. Check the electrode for carbon deposits.
    Recommended spark plug: 
    Manufacturers
    Products
    DENSO
    SK16R11

    NOTICE:
    If the electrode gap is larger than the standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG
OK


22.CHECK SPARKS AND IGNITION
  1. Remove the ignition coil from the cylinder head.

  1. Install the spark plug onto the ignition coil.

  1. Connect Techstream to the DLC3.

  1. Turn the power switch ON (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Fuel Cut All.

  1. Touch the spark plug tip to the cylinder head.

  1. Perform the Fuel Cut All operation (press the RIGHT or LEFT button to change to ON).

    NOTICE:
    When Fuel Cut All is OFF and the engine is cranked, fuel injection will occur.

  1. Crank the engine for less than 2 seconds and check for spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.



NG
Go to step 29
OK


23.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder.



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


24.CHECK HARNESS AND CONNECTOR (INJECTOR - HYBRID VEHICLE CONTROL ECU)


    A180469E01
  1. Disconnect the injector connector (of the misfiring cylinder).

  1. Disconnect the E4 ECM connector.

  1. Turn the power switch ON (IG).

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connections
    Specified Conditions
    No. 1
    I5-1 - Ground
    9 to 14 V
    No. 2
    I6-1 - Ground
    9 to 14 V
    No. 3
    I7-1 - Ground
    9 to 14 V
    No. 4
    I8-1 - Ground
    9 to 14 V

    Standard resistance:
    Cylinder
    Tester Connections
    Specified Conditions
    No. 1
    I5-2 - Ground
    10 kΩ or higher
    I5-2 - E4-2 (#10)
    Below 1 Ω
    No. 2
    I6-2 - Ground
    10 kΩ or higher
    I6-2 - E4-3 (#20)
    Below 1 Ω
    No. 3
    I7-2 - Ground
    10 kΩ or higher
    I7-2 - E4-4 (#30)
    Below 1 Ω
    No. 4
    I8-2 - Ground
    10 kΩ or higher
    I8-2 - E4-5 (#40)
    Below 1 Ω

  1. Reconnect the injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


25.INSPECT ECM TERMINAL VOLTAGE (MISFIRING CYLINDER)


    A124045E06
  1. Turn the power switch ON (IG).

  1. Measure the voltage between the terminals of the ECM connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    E4-2 (#10) - E4-7 (E01)
    9 to 14 V
    E4-3 (#20) - E4-7 (E01)
    9 to 14 V
    E4-4 (#30) - E4-7 (E01)
    9 to 14 V
    E4-5 (#40) - E4-7 (E01)
    9 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


26.CHECK FUEL INJECTOR ASSEMBLY (MISFIRING CYLINDER)
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).



NG
REPLACE FUEL INJECTOR ASSEMBLY
OK


27.CHECK VALVE CLEARANCE (MISFIRING CYLINDER)


NG
ADJUST VALVE CLEARANCE
OK


28.CHECK VALVE TIMING


NG
ADJUST VALVE TIMING
OK

REPLACE ECM 

29.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER (MISFIRING CYLINDER)
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 30
OK

REPLACE SPARK PLUG 

30.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER


NG
REPLACE ECM
OK

REPLACE IGNITION COIL