Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2014.12–2015.11
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low . The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. more than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A254107E17
0.885,3.01 0.583,3.01 false 3.375,1.042 3.115,1.281 true 3.427,1.646 2.885,1.646 true 3.427,1.333 2.865,1.51 true 3.427,2.24 2.906,2.094 false 3.427,2.542 2.771,2.313 true 3.427,2.823 2.875,2.51 false 2.25,2.76 1.698,3.073 true 0.167,2.906 0.594,3.073 0.427,0.167 10 false Cover 1.24,3.073 2.125,3.25 0.885,0.177 10 false Exhaust Gas 1.792,0.885 2.646,1.083 0.854,0.198 10 false Atmosphere 3.396,0.948 3.979,1.156 0.583,0.208 10 false Housing 3.448,1.271 4.688,1.438 1.24,0.167 10 false Platinum Electrode 3.448,1.573 4.667,1.927 1.219,0.354 10 false Solid Electrolyte (Zirconia Element) 3.448,2.469 3.958,2.646 0.51,0.177 10 false Heater 3.448,2.75 4.635,2.958 1.188,0.208 10 false Coating (Ceramic) 3.448,2.167 4.688,2.333 1.24,0.167 10 false Platinum Electrode 4.115,0.948 5.094,1.146 0.979,0.198 10 false Output Voltage 4.802,2.927 6.844,3.146 2.042,0.219 10 false Richer - Air fuel Ratio - Leaner 5.115,0.792 6.479,1 1.365,0.208 10 false Ideal Air fuel Mixture

DTC No. DTC Detection Condition Trouble Area
P0136

Abnormal voltage output:

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage does not increase to 0.69 V or higher.


(b) Heated oxygen sensor voltage does not decrease to less than 0.21 V.



·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system

·

EGR valve assembly


P0137

Low voltage (open):

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is less than 0.21 V.


(b) Target air fuel ratio is rich.



·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leak from exhaust system

·

EGR valve assembly


P0138

High voltage (short):

During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is higher than 0.69 V.


(b) Target air fuel ratio is lean.



·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

ECM

·

EGR valve assembly



MONITOR DESCRIPTION

Active Air fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136)


While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not decrease to less than 0.21 V and does not increase to 0.69 V or higher during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136.

A377016E08
2.948,2.115 3.115,1.74 3.115,1.74 3.26,1.74 false 2.781,2.344 2.99,2.615 2.99,2.615 3.156,2.615 false 0.135,0.115 4.771,0.552 4.635,0.438 10 false Heated Oxygen Sensor Circuit Malfunction (P0136: Abnormal Voltage) 2.26,1.385 3.115,1.802 0.854,0.417 10 false OFF 0.104,1.375 2.563,1.99 2.458,0.615 10 false Active air fuel ratio control 0.125,2.531 2.688,3.156 2.563,0.625 10 false Heated oxygen sensor voltage 2.104,2.146 2.958,2.563 0.854,0.417 10 false 0.69 V 2.083,2.896 2.938,3.313 0.854,0.417 10 false 0.21 V 3.229,2.521 4.083,2.938 0.854,0.417 10 false Abnormal 3.323,1.646 4.177,2.063 0.854,0.417 10 false Normal 4.719,1.292 5.573,1.708 0.854,0.417 10 false Operation 4.208,0.813 6.229,1.313 2.021,0.5 10 false Approximately 30 seconds


Open or Short in Heated Oxygen Sensor Circuit (DTC P0137 or P0138)


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, the OSC indicated an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137. When the target air fuel ratio is lean and the voltage output is higher than 0.69 V (rich) during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormally high and stores DTC P0138.

*: The TWC has the capability to store oxygen. The OSC and the emissions purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P0420).

A152992E97
5.813,3.792 6.021,4.052 false 4.292,2.063 4.406,1.74 4.406,1.74 4.583,1.74 false 5.344,2.406 5.438,1.719 5.438,1.719 5.625,1.719 false 5.698,3.021 5.823,2.563 5.823,2.563 6,2.563 false 5.75,6.583 5.948,6.104 5.948,6.104 6.083,6.104 false 0.063,0.052 3.76,0.26 3.698,0.208 10 false Heated Oxygen Sensor Circuit Low Voltage (P0137: Open) 0.281,1.219 1.177,1.563 0.896,0.344 10 false Active air fuel ratio control 0.281,3.208 1.271,3.563 0.99,0.354 10 false Heated oxygen sensor voltage 0.281,2.083 1.552,2.281 1.271,0.198 10 false Target air fuel ratio 1.979,2.031 2.927,2.396 0.948,0.365 10 false Stoichiometric Air Fuel Level 2.771,1.365 3.135,1.563 0.365,0.198 10 false OFF 2.49,3.479 2.979,3.677 0.49,0.198 10 false 0.21 V 0.063,4.208 3.781,4.417 3.719,0.208 10 false Heated Oxygen Sensor Circuit High Voltage (P0138: Short) 0.281,4.854 1.177,5.229 0.896,0.375 10 false Active air fuel ratio control 0.281,6.906 1.24,7.271 0.958,0.365 10 false Heated oxygen sensor voltage 0.281,5.74 1.573,5.938 1.292,0.198 10 false Target air fuel ratio 2.094,5.688 3.021,6.052 0.927,0.365 10 false Stoichiometric Air Fuel Level 2.698,4.938 3.052,5.135 0.354,0.198 10 false OFF 3.99,0.313 5.646,0.51 1.656,0.198 10 false Approximately 30 seconds 4.521,1.302 5.281,1.5 0.76,0.198 10 false Operation 4.479,4.927 5.177,5.125 0.698,0.198 10 false Operation 4.708,5.74 5.104,5.938 0.396,0.198 10 false Lean 4.656,1.646 5.219,1.844 0.563,0.198 10 false Normal 6.146,6.01 6.833,6.208 0.688,0.198 10 false Abnormal 5.688,1.625 6.333,1.823 0.646,0.198 10 false Abnormal 6.063,4.063 6.802,4.26 0.74,0.198 10 false Abnormal 6.052,2.479 6.615,2.677 0.563,0.198 10 false Normal 4.781,2.438 5.146,2.635 0.365,0.198 10 false Rich 2.5,6.677 2.99,6.875 0.49,0.198 10 false 0.69 V


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 2)
Required Sensors/Components (Related) Crank position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Heated Oxygen Sensor Voltage Check (Voltage Malfunction, High Voltage and Low Voltage)
Active air fuel ratio control Executing
Active air fuel ratio control begins when all of following conditions met: -
Auxiliary battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 70%

TYPICAL MALFUNCTION THRESHOLDS

P0136: Heated Oxygen Sensor Voltage Check (Voltage Malfunction)
Either of following conditions is met 1 or 2
1. Both of following conditions are met -
(a) Commanded air fuel ratio 14.4 or less
(b) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.69 V
2. Both of following conditions are met -
(c) Commanded air fuel ratio 14.8 or more
(d) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.69 V

P0137: Heated Oxygen Sensor Voltage Check (Low Voltage)
Both of following conditions are met -
(a) Commanded air fuel ratio 14.4 or less
(b) Heated oxygen sensor voltage Less than 0.21 V

P0138: Heated Oxygen Sensor Voltage Check (High Voltage)
Both of following conditions are met -
(a) Commanded air fuel ratio 14.8 or more
(b) Heated oxygen sensor voltage Higher than 0.69 V

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A264212E03
4.025,0.715 4.252,0.867 0.228,0.152 10 [C] 3.487,2.905 4.721,3.057 1.235,0.152 10 10 minutes or more 1.096,1.355 1.700,1.508 0.604,0.152 10 60 km/h 2.043,2.42 2.271,2.572 0.228,0.152 10 [A] 1.024,0.482 1.628,0.634 0.604,0.152 10 100 km/h 1.248,2.225 1.625,2.377 0.377,0.152 10 Idling 0.061,2.736 1.394,2.889 1.333,0.152 10 Power Switch on (IG) 1.738,2.429 1.558,2.801 1.558,2.801 1.418,2.801 false 2.68,2.131 2.907,2.283 0.228,0.152 10 [B] 2.338,2.915 3.138,3.067 0.801,0.152 10 Warming up 5.007,3.309 5.235,3.462 0.228,0.152 10 [D]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on [A].

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

8.

With the shift lever in D, drive the vehicle at 60 to 100 km/h (37 to 62 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0136, P0137 or P0138.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.


1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the tester on.

4.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

5.

Start the engine.

6.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

HINT:

During charging control, the engine speed is set at idle, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.


7.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

8.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

9.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.


HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increase and decreases in the fuel injection volume.



Tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case Air Fuel Ratio Sensor (Sensor 1) Output Voltage Heated Oxygen Sensor (Sensor 2) Output Voltage Main Suspected Trouble Area
1
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373791E01
2.896,0.969 3.427,1.25 0.531,0.281 10 false OK 0.948,1.167 2.021,1.5 1.073,0.333 10 false Below 3.1 V 0.625,0.792 2.115,1.167 1.49,0.375 10 false Higher than 3.4 V 0.156,0.24 1.438,0.635 1.281,0.396 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373789E01
0.583,0.76 2.042,1.198 1.458,0.438 10 false Higher than 0.55 V 0.969,1.135 1.938,1.448 0.969,0.313 10 false Below 0.4 V 0.208,0.271 1.635,0.677 1.427,0.406 10 false Output Voltage 2.896,0.948 3.427,1.26 0.531,0.313 10 false OK

-
2
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373789E01
0.583,0.76 2.042,1.198 1.458,0.438 10 false Higher than 0.55 V 0.969,1.135 1.938,1.448 0.969,0.313 10 false Below 0.4 V 0.208,0.271 1.635,0.677 1.427,0.406 10 false Output Voltage 2.896,0.948 3.427,1.26 0.531,0.313 10 false OK

·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

Air fuel ratio sensor circuit


3
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373791E01
2.896,0.969 3.427,1.25 0.531,0.281 10 false OK 0.948,1.167 2.021,1.5 1.073,0.333 10 false Below 3.1 V 0.625,0.792 2.115,1.167 1.49,0.375 10 false Higher than 3.4 V 0.156,0.24 1.438,0.635 1.281,0.396 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

·

Heated oxygen sensor

·

Heated oxygen sensor heater

·

Heated oxygen sensor circuit


4
A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

A373788E05
0.135,0.302 1.719,0.76 1.583,0.458 10 false Injection Volume 1.375,0.75 2.26,1.083 0.885,0.333 10 false 12.5% 1.385,1.167 2.271,1.5 0.885,0.333 10 false -12.5%

A373790E01
2.875,1.052 3.427,1.333 0.552,0.281 10 false NG 0.51,1.156 1.823,1.521 1.313,0.365 10 false Almost no reaction 0.354,0.469 1.49,0.906 1.135,0.438 10 false Output Voltage

·

Fuel injector assembly

·

Fuel pressure

·

Gas leak from exhaust system (air fuel ratio extremely rich or lean)



HINT:
·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2; and then press the graph button on the Data List view.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0138 is output A
DTC P0137 is output B
DTC P0136 is output C
DTC P0136, P0137 or P0138 and other DTCs are output D

HINT:

If any DTCs other than P0136, P0137 or P0138 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S2)

B

11.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2.


g.

Allow the engine to idle.


h.

Read the heated oxygen sensor output voltage while idling.

Result
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Below 1.0 V B



A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
A213127E04
1.5,1.76 1.125,1.344 false 2.229,2.354 1.896,2.021 false 1.125,2.354 1.458,2.021 false 0.177,0.125 0.396,0.313 0.219,0.188 10 false *a 0.885,1.188 1.104,1.375 0.219,0.188 10 false +B 2.24,2.354 2.656,2.542 0.417,0.188 10 false OX1B 0.875,2.354 1.094,2.542 0.219,0.188 10 false E2

a.

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 4 (E2) Always 10 kΩ or higher
2 (+B) - 3 (OX1B) Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Heated Oxygen Sensor)



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the power switch off and wait for 5 minutes or more.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C10-22 (HT1B) - C10-103 (OX1B) Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C10-22 (HT1B) - C9-103 (OX1B) Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio) Alternates between higher than and below 3.3 V OK
Remains higher than 3.3 V NG
Remains below 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor (AFS Voltage B1S1) voltage remains either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E56
5.813,2.469 6.25,1.365 false 5.5,2.26 6.26,1.375 false 5.656,1.656 6.26,1.375 false 5.563,2.448 5.844,2.667 false 3.01,1.24 2.854,1.656 false 4.396,1.844 4.094,1.677 false 3.583,2.563 3.188,2.906 false 1.958,1.979 2.125,1.979 false 1.958,2.948 2.156,2.948 false 1.542,1.906 1.917,2.063 0.375,0.156 10 false 3.3 V 2.656,0.26 3.083,0.458 0.427,0.198 10 false 12.5% 4.125,1.125 4.792,1.333 0.667,0.208 10 false -12.5% 1.656,2.896 1.906,3.094 0.25,0.198 10 false 1 V 1.667,3.396 1.906,3.594 0.24,0.198 10 false 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 false Malfunction 5.875,2.615 6.604,2.792 0.729,0.177 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.646,2.479 5.656,2.688 2.01,0.208 10 false Heated Oxygen Sensor Output 6.302,1.208 7.146,1.854 0.844,0.646 10 false Air Fuel Ratio Sensor Output 4.417,1.792 4.865,2.156 0.448,0.365 10 true Normal



OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

19.REPLACE AIR FUEL RATIO SENSOR
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut. When the sensor is normal, the sensor current will indicate less than 2.2 mA in this test.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


f.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


g.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



h.

Stop the vehicle.


i.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.


j.

Accelerate the vehicle to 60 km/h (37 mph) or more and decelerate for 5 seconds or more. Perform this 3 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


A152792E24
1.357,2.513 2.638,2.697 1.281,0.184 10 10 minutes or more 2.973,2.513 4.186,2.697 1.213,0.184 10 5 seconds or more 4.271,2.513 5.468,2.697 1.197,0.184 10 5 seconds or more 5.56,2.513 6.739,2.697 1.179,0.184 10 5 seconds or more 0.152,0.078 1.451,0.293 1.299,0.215 12 Driving Pattern: 0.348,1.224 1.006,1.602 0.658,0.378 10 60 km/h 0.348,2.055 0.884,2.415 0.536,0.360 10 0 km/h


k.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard current:

Less than 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the tester.





OK

14.REPLACE HEATED OXYGEN SENSOR

NG

19.REPLACE AIR FUEL RATIO SENSOR
7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2S B1S2.


g.

Change the fuel injection volume using the tester and monitor the voltage output of the heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.




OK

8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

11.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the tester.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio) Alternates between higher than and below 3.3 V OK
Remains higher than 3.3 V NG
Remains below 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor (AFS Voltage B1S1) voltage remains either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E56
5.813,2.469 6.25,1.365 false 5.5,2.26 6.26,1.375 false 5.656,1.656 6.26,1.375 false 5.563,2.448 5.844,2.667 false 3.01,1.24 2.854,1.656 false 4.396,1.844 4.094,1.677 false 3.583,2.563 3.188,2.906 false 1.958,1.979 2.125,1.979 false 1.958,2.948 2.156,2.948 false 1.542,1.906 1.917,2.063 0.375,0.156 10 false 3.3 V 2.656,0.26 3.083,0.458 0.427,0.198 10 false 12.5% 4.125,1.125 4.792,1.333 0.667,0.208 10 false -12.5% 1.656,2.896 1.906,3.094 0.25,0.198 10 false 1 V 1.667,3.396 1.906,3.594 0.24,0.198 10 false 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 false Malfunction 5.875,2.615 6.604,2.792 0.729,0.177 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.646,2.479 5.656,2.688 2.01,0.208 10 false Heated Oxygen Sensor Output 6.302,1.208 7.146,1.854 0.844,0.646 10 false Air Fuel Ratio Sensor Output 4.417,1.792 4.865,2.156 0.448,0.365 10 true Normal



OK

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)

NG

19.REPLACE AIR FUEL RATIO SENSOR
9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.





OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

10.INSPECT EGR VALVE ASSEMBLY
10.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

11.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C16-1 (HT1B) - C10-22 (HT1B) Always Below 1 Ω
C16-3 (OX1B) - C10-103 (OX1B) Always Below 1 Ω
C16-4 (E2) - C10-135 (EX1B) Always Below 1 Ω
C16-1 (HT1B) or C10-22 (HT1B) - Body ground Always 10 kΩ or higher
C16-3 (OX1B) or C10-103 (OX1B) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C16-1 (HT1B) - C9-22 (HT1B) Always Below 1 Ω
C16-3 (OX1B) - C9-103 (OX1B) Always Below 1 Ω
C16-4 (E2) - C9-135 (EX1B) Always Below 1 Ω
C16-1 (HT1B) or C9-22 (HT1B) - Body ground Always 10 kΩ or higher
C16-3 (OX1B) or C9-103 (OX1B) - Body ground Always 10 kΩ or higher




OK

14.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE HEATED OXYGEN SENSOR

NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136, P0137 or P0138.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136, P0137 or P0138 is output)
A
NORMAL
(DTC is not output)
B



A

17.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)

B

END

17.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.

·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).





OK

NG

18.INSPECT EGR VALVE ASSEMBLY
18.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly or air fuel ratio sensor (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

NG

19.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




NEXT

20.PERFORM CONFIRMATION DRIVING PATTERN
20.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138)
21.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136 or P0138.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136 or P0138 is output)
A
NORMAL
(DTC is not output)
B



A

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)

B

END

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.





OK

NG

23.INSPECT EGR VALVE ASSEMBLY
23.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

NG