Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2014.12–2015.11
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136 (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P0136).

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the power switch is turned off.

A269905E02
0.159,0.075 2.803,0.247 2.645,0.172 10 Reference (System Diagram of Sensor 2): 0.107,1.104 1.112,1.437 1.005,0.333 10 from Auxiliary Battery 3.249,1.989 4.737,2.171 1.488,0.181 10 Heated Oxygen Sensor 3.401,1.003 3.592,1.184 0.191,0.181 10 +B 3.795,0.789 4.230,0.970 0.436,0.181 10 Heater 3.781,1.279 4.240,1.460 0.459,0.181 10 Sensor 3.398,1.541 3.595,1.722 0.197,0.181 10 E2 4.43,1.01 4.810,1.191 0.380,0.181 10 HT1B 5,1.01 5.380,1.191 0.380,0.181 10 HT1B 4.43,1.539 4.859,1.720 0.429,0.181 10 OX1B 5,1.539 5.424,1.720 0.425,0.181 10 OX1B 5,2.089 5.384,2.270 0.385,0.181 10 EX1B 5.655,3.264 5.981,3.445 0.326,0.181 10 ECM 1.802,2.297 2.438,2.439 0.636,0.142 10 EFI-MAIN 1.089,1.28 1.721,1.422 0.631,0.142 10 EFI-MAIN 4.992,2.551 5.627,2.732 0.635,0.181 10 MREL


DTC No. DTC Detection Condition Trouble Area
P0037 Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

No. 1 integration relay

·

ECM


P0038 Heated oxygen sensor heater current reaches high limit.
(Hybrid IC high current limiter monitor input "Fail") (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

No. 1 integration relay

·

ECM


P102D Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037, P0038 and P102D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.




MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P0037
Time after heater on 10 seconds or more

P0038
Time after heater on 10 seconds or more

P102D
Time after heater on 10 seconds or more

CONFIRMATION DRIVING PATTERN

A198819E10
0.749,0.969 1.396,1.162 0.647,0.193 10 2500 rpm 0.946,1.739 1.352,1.900 0.406,0.161 10 Idling 0.423,2.006 1.301,2.333 0.878,0.327 10 Power Switch on (IG) 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.623 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.613,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on [A].

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and idle it for 5 minutes or more [B].

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 2500 rpm for 1 minute [C].

HINT:

During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform steps [C] and [D] after charging control has completed.


9.

Idle the engine for 5 minutes or more [D].

10.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0037, P0038 or P102D.

14.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A275986E08
2.385,0.625 2.615,0.802 0.229,0.177 10 false 2C 0.792,0.76 1.448,0.906 0.656,0.146 10 false EFI-MAIN 4.26,1.292 4.417,1.469 0.156,0.177 10 false 3 1.188,5.938 2.219,6.115 1.031,0.177 10 false Auxiliary Battery 0.458,0.625 0.667,0.802 0.208,0.177 10 false 2E 0.51,0.458 0.667,0.635 0.156,0.177 10 false 1 2.427,0.458 2.583,0.635 0.156,0.177 10 false 4 3.01,1.583 3.302,1.76 0.292,0.177 10 false C16 5.417,0.625 5.698,0.802 0.281,0.177 10 false C10 5.427,2.094 5.76,2.271 0.333,0.177 10 false C10 5.427,1.406 5.708,1.583 0.281,0.177 10 false C10 5.417,3.094 5.677,3.271 0.26,0.177 10 false A40 5.469,2.917 5.635,3.094 0.167,0.177 10 false 46 5.469,0.458 5.719,0.635 0.25,0.177 10 false 22 5.427,1.229 5.677,1.406 0.25,0.177 10 false 103 5.427,1.917 5.677,2.094 0.25,0.177 10 false 135 3.813,0.521 4.188,0.698 0.375,0.177 10 false HT1B 3.406,1.26 3.729,1.438 0.323,0.177 10 false E2 3.802,1.26 4.25,1.438 0.448,0.177 10 false OX1B 4.646,2.469 4.854,2.646 0.208,0.177 10 false *3 3,1.76 4.552,1.938 1.552,0.177 10 false Heated Oxygen Sensor 5.75,0.51 6.125,0.688 0.375,0.177 10 false HT1B 5.75,1.958 6.146,2.135 0.396,0.177 10 false EX1B 5.75,1.271 6.177,1.448 0.427,0.177 10 false OX1B 4.26,0.531 4.417,0.708 0.156,0.177 10 false 1 0.479,2.146 1.958,2.385 1.479,0.24 10 false No. 1 Integration Relay 6.177,4.875 6.542,5.052 0.365,0.177 10 false ECM 0.292,3.646 0.531,3.813 0.24,0.167 10 false P/I 1.49,1.229 2.125,1.375 0.635,0.146 10 false EFI-MAIN 3.917,6.281 4.75,6.469 0.833,0.188 10 false *3: Shielded 3.24,0.531 3.396,0.708 0.156,0.177 10 false 2 3.26,1.292 3.417,1.469 0.156,0.177 10 false 4 3.406,0.521 3.646,0.698 0.24,0.177 10 false +B 5.771,3.083 6.198,3.26 0.427,0.177 10 false MREL 1.021,5.073 1.396,5.229 0.375,0.156 10 false MAIN 1.927,1.948 2.156,2.125 0.229,0.177 10 false 2C 2.021,1.74 2.177,1.917 0.156,0.177 10 false 2 2.323,1.948 2.552,2.125 0.229,0.177 10 false 2C 2.458,1.74 2.615,1.917 0.156,0.177 10 false 3 5.146,0.625 5.365,0.802 0.219,0.177 10 false C9 5.146,2.094 5.365,2.271 0.219,0.177 10 false C9 5.146,1.406 5.396,1.583 0.25,0.177 10 false C9 5.156,0.448 5.406,0.625 0.25,0.177 10 false 22 5.125,1.229 5.375,1.406 0.25,0.177 10 false 103 5.115,1.917 5.365,2.094 0.25,0.177 10 false 135 5.479,0.813 5.656,0.99 0.177,0.177 10 false *1 5.49,1.583 5.667,1.76 0.177,0.177 10 false *1 5.479,2.26 5.656,2.438 0.177,0.177 10 false *1 5.177,0.813 5.354,0.99 0.177,0.177 10 false *2 5.188,1.573 5.365,1.75 0.177,0.177 10 false *2 5.167,2.25 5.344,2.427 0.177,0.177 10 false *2 3.917,5.969 4.75,6.156 0.833,0.188 10 false *2: for RHD 3.917,5.667 4.75,5.854 0.833,0.188 10 false *1: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2] (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DATA LIST / ACTIVE TEST).

·

When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
a.
U158895E04
2.344,2.01 1.875,2.219 false 2.406,1.927 2.677,2.125 0.271,0.198 10 false +B 0.208,0.156 0.427,0.375 0.219,0.219 10 false *a 0.594,2.198 1.01,2.49 0.417,0.292 10 false C16

Disconnect the heated oxygen sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C16-2 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C16-1 (HT1B) - C10-22 (HT1B) Always Below 1 Ω
C16-1 (HT1B) or C10-22 (HT1B) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C16-1 (HT1B) - C9-22 (HT1B) Always Below 1 Ω
C16-1 (HT1B) or C9-22 (HT1B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.


j.

Read the pending DTCs.


Result
Result Proceed to
DTC is not output A
DTC P0037, P0038 or P102D is output B


A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the No. 1 integration relay and ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

HINT:

Remove the ENG W/PMP relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-2 (+B) - 2C-4 Always Below 1 Ω
C16-2 (+B) or 2C-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR