Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module)
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM(w/o Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine fuel injection duration and to provide an appropriate air fuel ratio.

Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A275206E01
1.811,0.671 2.887,0.829 1.076,0.158 10 Power Transistor 1.615,0.223 1.872,0.380 0.257,0.158 10 +B 2.059,1.596 2.186,1.753 0.126,0.158 10 B 1.261,1.596 1.387,1.753 0.126,0.158 10 A 2.127,1.067 3.828,1.225 1.701,0.158 10 Platinum Hot Wire (Heater) 2.545,1.682 3.500,1.839 0.955,0.158 10 Output Voltage 2.274,2.361 3.961,2.519 1.687,0.158 10 Platinum Hot Wire (Heater) 4.28,2.361 6.381,2.519 2.100,0.158 10 Temperature Sensor (Thermistor) 4.341,1.529 3.741,2.339 false 2.092,1.16 1.893,1.555 false 4.514,1.679 4.769,2.321 false 0.16,0.185 0.974,0.820 0.814,0.634 10 Temperature Sensor (Thermistor) 1.536,1.544 1.168,0.257 1.168,0.257 0.981,0.257 false

DTC No. DTC Detection Condition Trouble Area
P0102 The mass air flow meter sub-assembly voltage is less than 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

No. 1 integration relay

·

ECM


P0103 The mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

No. 1 integration relay

·

ECM



HINT:

When any of these DTCs are output, check the air flow rate using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


Mass Air Flow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


271.0 or more
·

Open in E2G circuit



MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output voltage remains less than 0.2 V, or higher than 4.9 V for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0102 or P0103.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A275987E01
2.777,0.658 3.436,0.812 0.659,0.154 10 EFI NO. 2 3.414,1.726 3.694,1.878 0.279,0.152 10 C21 3.414,1.88 4.714,2.268 1.300,0.388 10 Mass Air Flow Meter Sub-assembly 0.579,2.32 1.131,2.650 0.552,0.330 10 Auxiliary Battery 0.945,1.531 2.572,1.700 1.627,0.170 10 No. 1 Integration Relay 1.531,1.188 2.183,1.342 0.652,0.154 10 EFI-MAIN 0.619,0.518 0.851,0.670 0.232,0.152 10 2E 0.661,0.339 0.761,0.491 0.100,0.152 10 1 0.719,1.322 0.919,1.473 0.200,0.152 10 2C 0.679,1.157 0.779,1.309 0.100,0.152 10 2 5.708,0.817 6.000,0.968 0.292,0.152 10 C10 5.764,0.638 5.937,0.790 0.173,0.152 10 91 5.708,1.321 5.981,1.473 0.274,0.152 10 C10 5.764,1.142 5.937,1.294 0.173,0.152 10 92 2.491,0.523 2.690,0.675 0.200,0.152 10 2C 2.534,0.344 2.634,0.496 0.100,0.152 10 4 6.04,2.367 6.450,2.518 0.410,0.152 10 MREL 6.315,3.058 6.649,3.210 0.334,0.152 10 ECM 3.463,0.416 3.654,0.568 0.191,0.152 10 +B 3.317,0.416 3.415,0.568 0.099,0.152 10 3 6.034,0.728 6.253,0.880 0.219,0.152 10 VG 6.034,1.233 6.329,1.385 0.295,0.152 10 E2G 4.387,0.735 4.606,0.887 0.219,0.152 10 VG 4.694,0.735 4.789,0.887 0.095,0.152 10 5 4.303,1.239 4.599,1.391 0.295,0.152 10 E2G 4.694,1.239 4.789,1.391 0.095,0.152 10 4 4.94,1.821 5.137,1.973 0.196,0.152 10 *3 5.705,2.597 5.992,2.749 0.287,0.152 10 A40 5.752,2.43 5.925,2.582 0.173,0.152 10 46 2.425,1.317 2.625,1.469 0.200,0.152 10 2C 2.401,1.164 2.501,1.316 0.100,0.152 10 3 0.363,1.046 0.622,1.232 0.258,0.185 10 P/I 0.419,1.689 0.808,1.841 0.389,0.152 10 MAIN 1.74,3.331 2.645,3.482 0.906,0.152 10 *1: for LHD 0.887,0.637 1.539,0.791 0.652,0.154 10 EFI-MAIN 5.425,0.817 5.717,0.968 0.292,0.152 10 C9 5.445,0.638 5.618,0.790 0.173,0.152 10 91 5.425,1.321 5.698,1.473 0.274,0.152 10 C9 5.445,1.142 5.618,1.294 0.173,0.152 10 92 5.764,0.994 5.937,1.146 0.173,0.152 10 *1 5.778,1.505 5.951,1.657 0.173,0.152 10 *1 5.444,0.985 5.617,1.136 0.173,0.152 10 *2 5.446,1.496 5.619,1.660 0.173,0.164 10 *2 2.895,3.331 3.800,3.482 0.906,0.152 10 *2: for RHD 4.122,3.331 5.027,3.482 0.906,0.152 10 *3: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0102 OR P0103)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
U158829E01
0.169,0.135 0.360,0.323 0.191,0.189 10 *a 0.262,2.106 0.603,2.287 0.340,0.181 10 C21 1.395,3.098 1.633,3.272 0.239,0.174 10 +B 1.786,2.423 1.541,3.08 false

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C21-3 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C21-5 (VG) - C10-91 (VG) Always Below 1 Ω
C21-4 (E2G) - C10-92 (E2G) Always Below 1 Ω
C21-5 (VG) or C10-91 (VG) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C21-5 (VG) - C9-91 (VG) Always Below 1 Ω
C21-4 (E2G) - C9-92 (E2G) Always Below 1 Ω
C21-5 (VG) or C9-91 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


b.

Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).


c.

Inspect the function of the mass air flow meter sub-assembly.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the tester on.


iv.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


v.

Start the engine.


vi.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


vii.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).





OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C21-4 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C21-4 (E2G) - C10-92 (E2G) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C21-4 (E2G) - C9-92 (E2G) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Remove the No. 1 integration relay and ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

HINT:

Remove the ENG W/PMP relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C21-3 (+B) - 2C-4 Always Below 1 Ω
C21-3 (+B) or 2C-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR