These DTCs indicate malfunctions relating to the primary circuit.
If DTC P0351 is output, check the No. 1 ignition coil assembly circuit.
If DTC P0352 is output, check the No. 2 ignition coil assembly circuit.
If DTC P0353 is output, check the No. 3 ignition coil assembly circuit.
If DTC P0354 is output, check the No. 4 ignition coil assembly circuit.
A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0351
P0352 P0353 P0354 |
No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Ignition system ·
Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil assembly and ECM ·
No. 1 to No. 4 ignition coil assemblies ·
ECM |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
| ECM Terminal Name | CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling |
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
| Required Sensors/Components (Main) | Igniter |
| Required Sensors/Components (Related) | Crank position sensor |
| Frequency of Operation | Continuous |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG) and turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Idle the engine for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0351, P0352, P0353 or P0354.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the ignition coil assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-4 (GND) - Body ground | Always | Below 1 Ω |
| C6-4 (GND) - Body ground | Always | Below 1 Ω |
| C7-4 (GND) - Body ground | Always | Below 1 Ω |
| C8-4 (GND) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the ignition coil assembly connectors.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-1 (+B) - C5-4 (GND) | Power switch on (IG) | 11 to 14 V |
| C6-1 (+B) - C6-4 (GND) | Power switch on (IG) | 11 to 14 V |
| C7-1 (+B) - C7-4 (GND) | Power switch on (IG) | 11 to 14 V |
| C8-1 (+B) - C8-4 (GND) | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Ignition Coil Assembly) |
OK
NG
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-2 (IGF) - C10-102 (IGF1) | Always | Below 1 Ω |
| C6-2 (IGF) - C10-102 (IGF1) | Always | Below 1 Ω |
| C7-2 (IGF) - C10-102 (IGF1) | Always | Below 1 Ω |
| C8-2 (IGF) - C10-102 (IGF1) | Always | Below 1 Ω |
| C5-3 (IGT1) - C10-57 (IGT1) | Always | Below 1 Ω |
| C6-3 (IGT2) - C10-56 (IGT2) | Always | Below 1 Ω |
| C7-3 (IGT3) - C10-55 (IGT3) | Always | Below 1 Ω |
| C8-3 (IGT4) - C10-54 (IGT4) | Always | Below 1 Ω |
| C5-3 (IGT1) or C10-57 (IGT1) - Body ground | Always | 10 kΩ or higher |
| C6-3 (IGT2) or C10-56 (IGT2) - Body ground | Always | 10 kΩ or higher |
| C7-3 (IGT3) or C10-55 (IGT3) - Body ground | Always | 10 kΩ or higher |
| C8-3 (IGT4) or C10-54 (IGT4) - Body ground | Always | 10 kΩ or higher |
| C5-2 (IGF), C6-2 (IGF), C7-2 (IGF), C8-2 (IGF) or C10-102 (IGF1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-2 (IGF) - C9-102 (IGF1) | Always | Below 1 Ω |
| C6-2 (IGF) - C9-102 (IGF1) | Always | Below 1 Ω |
| C7-2 (IGF) - C9-102 (IGF1) | Always | Below 1 Ω |
| C8-2 (IGF) - C9-102 (IGF1) | Always | Below 1 Ω |
| C5-3 (IGT1) - C9-57 (IGT1) | Always | Below 1 Ω |
| C6-3 (IGT2) - C9-56 (IGT2) | Always | Below 1 Ω |
| C7-3 (IGT3) - C9-55 (IGT3) | Always | Below 1 Ω |
| C8-3 (IGT4) - C9-54 (IGT4) | Always | Below 1 Ω |
| C5-3 (IGT1) or C9-57 (IGT1) - Body ground | Always | 10 kΩ or higher |
| C6-3 (IGT2) or C9-56 (IGT2) - Body ground | Always | 10 kΩ or higher |
| C7-3 (IGT3) or C9-55 (IGT3) - Body ground | Always | 10 kΩ or higher |
| C8-3 (IGT4) or C9-54 (IGT4) - Body ground | Always | 10 kΩ or higher |
| C5-2 (IGF), C6-2 (IGF), C7-2 (IGF), C8-2 (IGF) or C9-102 (IGF1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR).
Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).
Do not change the location of the connectors.
Perform a simulation test.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Same DTC output | A |
| Different ignition coil DTC output | B |
Perform "Inspection After Repair" after replacing the ignition coil assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).
A
B
Disconnect the ignition coil assembly connectors.
Remove the No. 1 integration relay from the No. 2 engine room relay block and No. 2 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-1 (+B) - 2D-4 | Always | Below 1 Ω |
| C6-1 (+B) - 2D-4 | Always | Below 1 Ω |
| C7-1 (+B) - 2D-4 | Always | Below 1 Ω |
| C8-1 (+B) - 2D-4 | Always | Below 1 Ω |
| C5-1 (+B), C6-1 (+B), C7-1 (+B), C8-1 (+B) or 2D-4 - Body ground | Always | 10 kΩ or higher |
OK
NG