Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2014.12–2015.11
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0277909 SFI SYSTEM C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0115 (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P0115).

DTC No. DTC Detection Condition Trouble Area
P0116 When either of the following conditions is met (2 trip detection logic).
·

During engine warm up after cold engine starts, change in engine coolant temperature sensor output is below threshold

·

In duration between warmed engine stopped and next cold engine starts, change in engine coolant temperature sensor output below threshold


·

Water inlet with thermostat sub-assembly

·

Engine coolant temperature sensor



MONITOR DESCRIPTION

Engine Coolant Temperature Sensor Cold Start Monitor

The monitor runs when the engine is started cold. If the change in engine coolant temperature sensor output until the engine is warmed up completely is less than the threshold, it is determined that a malfunction has occurred in the engine coolant temperature sensor. When this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.


Engine Coolant Temperature Sensor Soak Monitor

The ECM compares the engine coolant temperature when the fully warmed up engine is stopped and when the engine is started on the next trip when 5 hours or more has elapsed since the engine was stopped. If the change in engine coolant temperature sensor output is less than the threshold, it is determined that a malfunction has occurred in the engine coolant temperature sensor. When this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.


MONITOR STRATEGY

Required Sensors/Components Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A378743E07
2.135,1.917 2.469,2.292 0.333,0.375 10 false [A] 4.208,0.292 6.01,0.594 1.802,0.302 10 false Total of 5 minutes or more 4.813,0.667 5.146,1.042 0.333,0.375 10 false [D] 6.156,2.865 6.49,3.24 0.333,0.375 10 false [E] 3.99,2.885 4.323,3.26 0.333,0.375 10 false [C] 3.198,1.635 3.531,2.01 0.333,0.375 10 false [B] 1.083,1.76 1.583,2.156 0.5,0.396 10 false Idling 0.573,2.042 1.438,2.563 0.865,0.521 10 false Power Switch on (IG) 0.917,1.156 2.615,1.563 1.698,0.406 10 false 40 km/h 2.74,2.552 4.063,2.938 1.323,0.385 10 false 5 minutes or more 1.375,3.167 6.729,3.542 5.354,0.375 10 false HINT: Start the engine when the engine coolant temperature is 60°C or less

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

4.

Check that the engine coolant temperature is 60°C (140°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the power switch off and wait for at least 30 seconds.

7.

Turn the power switch on (IG) and turn the tester on [A].

8.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

9.

Start the engine and idle it for 5 minutes or more [B].

HINT:

If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.


10.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0116.

14.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



15.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.


16.

Check the DTC judgment result again [E].

HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.



CAUTION / NOTICE / HINT

HINT:
·

If any of DTCs P0115, P0117 or P0118 are set simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When the DTC is output, check the engine coolant temperature using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0116 is output A
DTC P0116 and other DTCs are output B

HINT:

If any DTCs other than P0116 are output, troubleshoot those DTCs first.




A

2.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

B

2.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature) (See page Engine / Hybrid System>1NZ-FXE (COOLING)>THERMOSTAT>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).




OK

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY