19100P
1. PERFORM SPARK TEST
Check for DTCs (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR).
If any DTC is output, perform troubleshooting procedures for that DTC.
Remove the ignition coil assemblies and spark plugs (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).
Disconnect the 4 injector connectors.
Set the vehicle to inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).(Step 3)
Install the spark plug into the ignition coil assembly, and then connect the ignition coil connector. (Step 4)
Ground the spark plug. (Step 5)
Check that spark occurs at each spark plug while the engine is being cranked. (Step 6)
Be sure to ground the spark plugs when checking them.
Do not crank the engine for more than 2 seconds.
Cranking will stop if the power switch is pushed again for models with cranking holding function.
If a spark plug has been struck or dropped, replace it.
If an ignition coil assembly has been struck or dropped, replace it.
Repeat steps 3 to 6 for each spark plug and ignition coil assembly.
If spark does not occur for any cylinder, perform the following Inspect Ignition Coil and Spark Test procedure.
Connect the 4 fuel injector connectors.
Install the spark plugs and ignition coil assemblies (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).
Check for DTCs (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR).
Clear the DTCs (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR).
19500
2.INSPECT IGNITION COIL AND SPARK TEST
Perform "Inspection After Repair" after replacing the spark plug and ignition coil assembly (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).
Check that the wire harness side connector of the ignition coil assembly is securely connected.
| Result | Action |
|---|---|
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each ignition coil assembly.
Replace the ignition coil assembly with a known good one.
Set the vehicle to inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Perform the spark test again.
| Result | Action |
|---|---|
| NG | Go to next step |
| OK | Replace ignition coil assembly |
Perform a spark test on each spark plug.
Replace the spark plug with a known good one.
Set the vehicle to inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
19100P
3.CHECK SPARK PLUG
Do not use a wire brush for cleaning.
Do not adjust the electrode gap of a used spark plug.
Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION).
Check the electrode using a megohmmeter:
| *a | Ground |
Using a megohmmeter, measure the insulation resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Spark plug (terminal part) - Body ground | Always | 10 MΩ or higher |
If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:
Quickly accelerate the engine to 2500 rpm 5 times.
Remove the spark plug (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its thread and insulator.
If there is any damage, replace the spark plug.
| Manufacturer | Spark Plug Type |
|---|---|
| DENSO | FK16R-A8 |
Reference:
Check the spark plug electrode gap.
1.1 mm (0.0433 in.)
If the gap is more than the maximum, replace the spark plug.
Never attempt to adjust the gap of a used plug.
0.7 to 0.8 mm (0.0276 to 0.0315 in.)
| *a | Spark plug electrode gap |
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
588 kPa (6.0 kgf/cm2, 85 psi)
20 seconds or less
Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
Install the spark plug (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).