Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A08-264  DC / DC Converter Status Circuit  


DESCRIPTION

The DC/DC converter converts the DC 144 V of the HV battery into DC 12 V in order to supply power to areas such as the vehicle's lighting, audio, and ECU systems. In addition, it charges the auxiliary battery. A transistor bridge circuit initially converts DC 144 V into alternating current, and a transformer lowers its voltage. Then, it is rectified and smoothed (into DC) and converted into DC 12 V. The DC/DC converter controls the output voltage in order to keep a constant voltage at the terminals of the auxiliary battery.

The power management control ECU uses the NODD signal line to transmit a stop command to the DC/DC converter and receive signals indicating the normal or abnormal condition of the 12 V charging system. If the vehicle is being driven with an inoperative DC/DC converter, the voltage of the auxiliary battery will drop, which will prevent the continued operation of the vehicle. Therefore, the power management control ECU monitors the operation of the DC/DC converter and alerts the driver if it detects a malfunction.

A280191E03
0.813,0.958 1.292,1.177 0.479,0.219 10 false DC/DC 0.719,2.604 1.375,2.833 0.656,0.229 10 false FL-MAIN 1.865,0.698 2.229,0.906 0.365,0.208 10 false AMD 0.865,3.094 1.51,3.531 0.646,0.438 10 false Auxiliary Battery 3.083,4.031 5.219,4.5 2.135,0.469 10 false Power Management Control ECU 1.885,3.469 3.281,4.042 1.396,0.573 10 false Inverter with Converter Assembly 2.229,2.438 3.406,2.708 1.177,0.271 10 false DC/DC Converter 3.396,2.208 3.844,2.417 0.448,0.208 10 false NODD 4.042,2.219 4.469,2.417 0.427,0.198 10 false VLO 4.938,2.219 5.344,2.438 0.406,0.219 10 false IGCT 6.177,2.531 6.906,2.969 0.729,0.438 10 false from IGCT Relay 5.146,0.313 5.802,0.552 0.656,0.24 10 false DC144 V

DTC No. INF Code DTC Detection Condition Trouble Area
P0A08 264 DC/DC converter malfunction or the auxiliary battery voltage drops to 11 V or less with the power switch on (READY).*1
(1 trip detection logic)
·

Wire harness or connector

·

Inverter cooling system

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Inverter with converter assembly

·

Fusible link (DC/DC)

·

Power management control ECU



WIRING DIAGRAM

A279003E06
2.26,5.99 4.427,6.396 2.167,0.406 10 false Power Management Control ECU 0.646,5.146 1.74,5.354 1.094,0.208 10 false Auxiliary Battery 5.677,5.99 7.063,6.667 1.385,0.677 10 false Inverter with Converter Assembly 2.583,3.198 3.021,3.375 0.438,0.177 10 false IGCT 1.406,2.604 2.177,2.781 0.771,0.177 10 false IGCT-MAIN 2.5,0.906 3,1.083 0.5,0.177 10 false DC/DC 0.552,4.24 1.208,4.417 0.656,0.177 10 false MAIN 3.958,4.177 4.427,4.354 0.469,0.177 10 false MREL 3.948,4.563 4.385,4.74 0.438,0.177 10 false NODD 4.177,5.521 4.427,5.698 0.25,0.177 10 false E1 6.042,4.573 6.542,4.75 0.5,0.177 10 false NODD 6.052,0.729 6.438,0.906 0.385,0.177 10 false AMD 6.052,2.458 6.469,2.635 0.417,0.177 10 false IGCT 5.656,2.448 5.979,2.625 0.323,0.177 10 false A47 5.667,4.646 5.958,4.823 0.292,0.177 10 false A47 4.458,4.177 4.729,4.354 0.271,0.177 10 false A39 4.458,4.646 4.771,4.823 0.313,0.177 10 false A38 4.448,5.604 4.74,5.781 0.292,0.177 10 false G57 3.479,4.844 3.938,5.021 0.458,0.177 10 false 100 Ω 2.917,4.917 3.375,5.094 0.458,0.177 10 false 47 kΩ 2.917,5.385 3.375,5.563 0.458,0.177 10 false 82 kΩ 4.479,0.74 4.74,0.917 0.26,0.177 10 false 1D 3.875,2.323 4.073,2.5 0.198,0.177 10 false 2 3.385,2.323 3.583,2.5 0.198,0.177 10 false 1 2.302,2.823 2.5,3 0.198,0.177 10 false 2 3.115,2.823 3.313,3 0.198,0.177 10 false 1 3.115,2.344 3.313,2.521 0.198,0.177 10 false 5 2.302,2.354 2.5,2.531 0.198,0.177 10 false 3 2.01,2.344 2.208,2.521 0.198,0.177 10 false 2 1.5,2.333 1.698,2.51 0.198,0.177 10 false 1 4.542,5.406 4.75,5.615 0.208,0.208 10 false 6 4.51,4.469 4.823,4.646 0.313,0.177 10 false 21 4.531,4 4.646,4.177 0.115,0.177 10 false 6 5.719,4.458 5.99,4.635 0.271,0.177 10 false 12 5.76,2.25 5.865,2.427 0.104,0.177 10 false 1 4.531,0.542 4.625,0.719 0.094,0.177 10 false 1 1.031,1.438 4.563,1.781 3.531,0.344 10 false Engine Room Relay Block and Junction block Assembly 0.656,3.531 4.906,3.719 4.25,0.188 10 false No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly 3.313,2.594 4.135,2.771 0.823,0.177 10 false IGCT NO. 4 0.802,0.74 1.063,0.917 0.26,0.177 10 false 1E 0.854,0.542 0.948,0.719 0.094,0.177 10 false 1

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

If there is a malfunction in the DC/DC converter internal circuit, P0A08-264 is stored within 2 minutes of the power switch being turned on (READY) regardless of the auxiliary battery voltage.

·

If the auxiliary battery voltage is low, the power switch will turn off regardless of DTCs being stored or not.

·

After repair, clear the DTCs, turn the power switch off and wait for 30 seconds or more and perform the following procedure to confirm that the auxiliary battery low voltage indicated by this DTC has been repaired.

(a)

Wait for 2 minutes with the shift lever in P, the power switch on (READY) and the following conditions met, then confirm that Data List item "+B" is between 13.0 and 15.0 V.

(If charging is not performed and the electrical load increases, +B voltage may not be steady and gradually drops.)

(1)

Headlight switch is in the HI position.

(2)

A/C blower fan switch is in the HI position.

(3)

Window defogger switch is turned on.




·

If the DC/DC converter has an internal malfunction, DTC P0A08-264 is stored regardless of the auxiliary battery voltage after performing this procedure.

·

If the auxiliary battery voltage drops, the power switch off regardless of DTCs being stored or not.

·

By performing the following procedure, the DC/DC converter function can be checked.

(a)

Connect the AC/DC 400 A probe to the positive auxiliary battery cable.

(1)

Turn the power switch on (READY) and leave the vehicle as it is until the electric current flowing into the auxiliary battery becomes 10 A or less.

(2)

Turn the power switch on (READY) and the headlight switch and A/C blower fan switch in the HI position, and the window defogger turned on.

(3)

Confirm that the current drawn from the auxiliary battery is 0 A or lower and the auxiliary battery voltage is between 13.0 and 15.0 V.




·

This DTC may be stored when a part other than the DC/DC converter is malfunctioning or depending on user operation.

Malfunction cases to store DTC P0A08-264
Malfunction Case Remarks Inspection Step
Fuse is blown. (DC/DC) - 4
High-voltage insulation between the inverter, generator (MG1), motor (MG2) and body ground is poor (body ground). DTC P0AA6 may be stored if the ground potential fluctuates due to a high-voltage insulation malfunction. 1
A signal connector of the power management control ECU or inverter is not connected securely. - 2. 3
The DC/DC converter is malfunctioning. Inspect the DC/DC converter function. 9
Control is suspended due to overheating. (The inverter water pump assembly is malfunctioning, the coolant is not sufficient, a hose is clogged, etc.) When the inverter is overheating, the DC/DC converter has self protection control that suspends the DC/DC converter control. As that time, this DTC may be stored.
The suspended DC/DC converter control will return to normal by clearing the DTCs and turning the power switch off.
10 to 13, 17


·

If this vehicle is used to jump start another vehicle with a discharged battery, a fuse may blow due to overcurrent or the DC/DC converter self-protection may be activated.

In addition, if this vehicle is jump started by a vehicle with a 24 V auxiliary battery or the auxiliary battery cables are connected to the opposite auxiliary battery terminals, the same malfunction may occur and this DTC may be stored. (The suspended DC/DC converter control will return to normal by clearing the DTCs and turning the power switch off.)


·

If the DC/DC converter is malfunctioning, the auxiliary battery cannot be charged. Therefore, once the power switch is turned off, it may be impossible to turn it on (READY) again if the auxiliary battery is completely discharged. In this case, charge the auxiliary battery. Be careful as charging is not performed during the inspection.

·

If the power switch turns off immediately after it is turned on (READY), the auxiliary battery voltage may be low. Charge the auxiliary battery.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A08-264 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B


DTC No. Relevant Diagnosis
P0A93-346 Inverter Cooling System Performance
P0A94-547, 548, 549 DC / DC Converter Performance
P0AA6-526, 613 Hybrid Battery Voltage System Isolation Fault
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE6-225 Hybrid Battery Precharge Contactor Control Circuit Low
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P3004-131, 803 High Voltage Power Resource
P314A-828 Inverter Coolant Pump Speed Signal


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK FUSIBLE LINK (DC/DC)

NG

CONNECT SECURELY

4.CHECK FUSIBLE LINK (DC/DC)
a.

Disconnect connector 1E from the engine room relay block and junction block assembly.


b.
U159096E02
1.083,0.25 1.302,0.417 0.219,0.167 10 false 1E 1.531,1.094 1.75,1.26 0.219,0.167 10 false 1D

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-1 - 1D-1 (AMD) Always Below 1 Ω



c.

Check the fusible link (DC/DC) in the engine room relay block and junction block assembly for improper installation.

OK:

The fusible link is installed securely.



d.

Connect the 1E connector to the engine room relay block and junction block assembly.



OK

5.CHECK CABLE AND WIRE HARNESS

NG

REPLACE FUSIBLE LINK (DC/DC)

5.CHECK CABLE AND WIRE HARNESS
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
U158995E02
3.115,0.865 2.99,0.927 false 1.938,0.625 1.854,0.49 true 1.042,1.115 1.208,1.281 0.167,0.167 10 true W 1.646,1.563 1.802,1.833 0.156,0.271 10 true V 1.813,1.667 1.99,1.865 0.177,0.198 10 true W 2.365,1.917 2.542,2.094 0.177,0.177 10 false V 2.094,1.813 2.281,2 0.188,0.188 10 false U 1.656,0.365 1.844,0.521 0.188,0.156 10 true *1 3.125,0.771 3.365,0.958 0.24,0.188 10 true *2 1.688,1.906 1.896,2.073 0.208,0.167 10 false a4 1.073,1.604 1.281,1.771 0.208,0.167 10 true a2 1.396,1.469 1.635,1.781 0.24,0.313 10 true U

Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a2-1 (W) - Body ground and shield ground Power switch off 1 MΩ or higher
a2-2 (U) - Body ground and shield ground Power switch off 1 MΩ or higher
a2-3 (V) - Body ground and shield ground Power switch off 1 MΩ or higher
a4-1 (W) - Body ground and shield ground Power switch off 1 MΩ or higher
a4-2 (U) - Body ground and shield ground Power switch off 1 MΩ or higher
a4-3 (V) - Body ground and shield ground Power switch off 1 MΩ or higher


Text in Illustration
*1 Motor Cable (for MG1)
*2 Motor Cable (for MG2)

HINT:

Perform this inspection while the motor cable (for MG1) and motor cable (for MG2) are connected.



e.

Install the inverter cover.


f.

Install the inverter terminal cover.



OK

6.CHECK AMD TERMINAL VOLTAGE (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

NG

14.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)
6.CHECK AMD TERMINAL VOLTAGE (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.
U159036E02
0.896,0.677 1.104,0.844 0.208,0.167 10 false 1D

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1D-1 (AMD) - Body ground Power switch off Same as auxiliary battery voltage



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.



OK

7.CHECK AMD TERMINAL CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK AMD TERMINAL CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A267465

Check that the bolt for the AMD terminal is tightened to the specified torque, the AMD terminal is connected securely, and there is no contact problem.

Torque:

T=8.0 N*m {82 kgf*cm, 71in.*lbf }


Result:
Result Proceed to
There are no arc marks. The terminal is connected securely and there is no contact problem. A
There are no arc marks. The terminal is not connected securely and there is a contact problem. B
There are arc marks. - C




A

8.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)

B

CONNECT SECURELY

C

REPLACE MALFUNCTIONING PARTS

8.CHECK HARNESS AND CONNECTOR (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.
U158868E01
0.102,0.067 0.285,0.232 0.183,0.165 10 *a 0.131,1.228 0.625,1.383 0.494,0.155 10 NODD 1.27,1.012 0.688,1.303 false 1.556,0.19 1.820,0.371 0.264,0.181 10 A47

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A47-12 (NODD) - Body ground Power switch off 110 to 150 kΩ


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Connect the inverter with converter assembly connector.



OK

9.CHECK DC/DC CONVERTER FUNCTION

NG

16.INSPECT POWER MANAGEMENT CONTROL ECU (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)
9.CHECK DC/DC CONVERTER FUNCTION
HINT:

The current at the AMD terminal cannot be measured directly because of space limitations. Measure the current flowing at the auxiliary battery instead.


a.
A174427E07
0.646,0.99 0.823,0.615 0.823,0.615 0.938,0.615 false 0.979,0.542 1.552,0.906 0.573,0.365 10 Probe Direction 0.167,1.646 1.406,2.156 1.24,0.51 10 Current Flowing into Auxiliary Battery

Connect the AC/DC 400 A probe to the positive auxiliary battery line.


b.

Install the service plug grip.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (READY) and leave the vehicle as it is until the electric current flowing into the auxiliary battery becomes 10 A or less.

HINT:

If the power switch turns off immediately after it is turned on (READY), auxiliary battery voltage may be low.

Recharge the auxiliary battery and perform this procedure again.



e.
A174428E05
0.698,0.844 0.885,0.479 0.885,0.479 1,0.479 false 1.073,0.385 1.667,0.729 0.594,0.344 10 Probe Direction 0.208,1.531 1.208,2.042 1,0.51 10 Current Flowing from Auxiliary Battery

Measure the current flowing from the auxiliary battery with the power switch on (READY), the headlight position switch and blower motor switch in the HI position, and the rear window defogger turned on.

Standard Current:
Item Condition Specified Condition
Current flowing from auxiliary battery Power switch on (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
0 A or less
(no current from auxiliary battery)



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Item Condition Specified Condition
Auxiliary battery voltage Power switch on (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
13 to 15 V



g.

Turn the power switch off.



OK

10.CHECK QUANTITY OF HV COOLANT

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

10.CHECK QUANTITY OF HV COOLANT

A

11.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR HV COOLANT LEAK AND ADD HV COOLANT

11.CHECK COOLANT HOSE

OK

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)

NG

CORRECT THE PROBLEM

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)

OK

13.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

13.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read the freeze frame data Ambient Temperature using the intelligent tester.


e.

Check if the freeze frame data Ambient Temperature is below freezing.

Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the HV coolant. A
Ambient Temperature value is below freezing temperature of the HV coolant. B


HINT:
·

HV coolant (SLLC) with a 30% concentration freezes at -15 °C (5°F) and HV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the HV coolant freezes in the HV radiator or HV water pump, the coolant temperature in the inverter with converter assembly rises because the HV coolant cannot circulate. As a result, a DTC may be set.

·

A DTC is set when the water pump impeller cannot rotate due to freezing of the HV coolant.

·

If a DTC is set due to freezing of HV coolant, the problem cannot be reproduced. Judge whether freezing of HV coolant occurred according to the freeze point of the HV coolant, HV coolant change history and ambient temperature when the DTC was set.




f.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

17.REPLACE HV COOLANT
14.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258645

Remove the inverter cover from the inverter with converter assembly.


d.
A258647

Disconnect the motor cable (for MG1) from the inverter with converter assembly.


e.
U159088E01
0.092,0.158 0.331,0.331 0.239,0.173 10 *a 0.384,0.811 0.581,0.984 0.197,0.173 10 *1 2.736,1.229 2.947,1.392 0.211,0.163 10 a2 1.103,1.909 1.282,2.074 0.179,0.165 10 W 1.627,1.909 1.806,2.074 0.179,0.165 10 U 2.159,1.915 2.338,2.080 0.179,0.165 10 V 1.298,1.745 1.238,1.892 false 1.699,1.746 1.699,1.892 false 2.096,1.746 2.174,1.892 false 0.859,0.892 0.582,0.892 false

Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a2-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
a2-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
a2-3 (V) - Body ground and shield ground Power switch off 100 MΩ or higher


Text in Illustration
*1 Shield Ground
*a Motor Cable (for MG1)
(Inverter with Converter Assembly Side)


f.

Connect the motor cable (for MG1).


g.

Install the inverter cover.


h.

Install the inverter terminal cover.



OK

15.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

18.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)
15.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258644

Remove the inverter terminal cover from the inverter with converter assembly.


c.
A258646

Disconnect the motor cable (for MG2) from the inverter with converter assembly.


d.
U159091E01
0.117,0.11 0.343,0.336 0.225,0.225 10 *a 0.324,0.878 0.570,1.059 0.246,0.181 10 *1 1.183,1.932 1.371,2.097 0.188,0.165 10 W 1.676,1.938 1.864,2.103 0.188,0.165 10 U 2.157,1.932 2.345,2.097 0.188,0.165 10 V 1.345,1.763 1.303,1.932 false 1.733,1.763 1.733,1.938 false 2.113,1.763 2.183,1.932 false 0.893,0.973 0.504,0.973 false 2.77,1.234 2.981,1.397 0.211,0.163 10 a4

Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
a4-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher
a4-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
a4-3 (V) - Body ground and shield ground Power switch off 100 MΩ or higher


Text in Illustration
*1 Shield Ground
*a Motor Cable (for MG2)
(Inverter with Converter Assembly Side)


e.

Connect the motor cable (for MG2).


f.

Install the inverter terminal cover.



OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

20.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)
16.INSPECT POWER MANAGEMENT CONTROL ECU (RESISTANCE VALUE OF NODD INSIDE POWER MANAGEMENT CONTROL ECU)
a.
U183172E02
0.865,1.958 1.094,2.396 true 1.823,1.833 2.063,2.396 true 0.688,1.156 0.958,1.323 0.271,0.167 10 false A38 1.906,1.156 2.198,1.323 0.292,0.167 10 false G57 0.177,0.229 0.365,0.417 0.188,0.188 10 false *a 0.833,2.417 1.271,2.604 0.438,0.188 10 false NODD 2.052,2.406 2.24,2.594 0.188,0.188 10 false E1

Disconnect all the connectors from the power management control ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-21 (NODD) - G57-6 (E1) Power switch off 110 to 150 kΩ


Text in Illustration
*a Component without harness connected
(Power Management Control ECU)


c.

Connect the power management control ECU connectors.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

18.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

A

19.CHECK MOTOR CABLE (FOR MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

20.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

A

21.CHECK MOTOR CABLE (FOR MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY