Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.12–2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A93-346  Inverter Cooling System Performance  


DESCRIPTION

The inverter converts the high-voltage direct current of the HV battery into the alternating current for MG1 and MG2. The inverter generates heat during the conversion process. Therefore, the inverter is cooled by a special cooling system consisting of the inverter water pump assembly, the cooling fan, and a radiator. This cooling system is independent of the engine cooling system. The hybrid vehicle control ECU monitors the inverter water pump assembly, cooling fan, and cooling system, and detects the following malfunctions.

A267468E03
5.479,1.354 6.01,1.188 false 4.031,2.063 2.042,0.49 true 2.208,4.604 1.927,5.021 false 4.292,3.896 4.563,5.323 true 1.854,0.375 2.104,0.604 0.25,0.229 10 false *3 1.76,4.979 2.01,5.208 0.25,0.229 10 false *4 4.51,5.344 4.76,5.573 0.25,0.229 10 false *1 6.042,1.083 6.292,1.313 0.25,0.229 10 false *2

Text in Illustration
*1 Inverter Water Pump Assembly *2 Inverter Reserve Tank Assembly
*3 Inverter with Converter Assembly *4 Radiator Assembly (HV)

DTC No. INF Code DTC Detection Condition Trouble Area
P0A93 346 Inverter cooling system malfunction
HV cooling temperature increases and the temperature of any inverter with converter assembly related parts increases.
(1 trip detection logic)
·

Inverter cooling system

·

Inverter water pump assembly

·

Inverter with converter assembly

·

Cooling fan system



Related Data List
DTC No. INF Code Data List Item
P0A93 346
·

Inverter Coolant Water Temperature

·

Inverter Temp-(MG1)

·

Inverter Temp-(MG2)

·

DC/DC Cnv Temp (Upper)

·

DC/DC Cnv Temp (Lower)

·

Inverter W/P Revolution



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform a road test according to the freeze frame data "Vehicle Spd" for approximately 15 minutes.

During the road test, check Data List items "Inverter Coolant Water Temperature", "Inverter Temp-(MG2)", "Inverter Temp- (MG1)" and "DC/DC Cnv Temp (Upper)" to prevent them from overheating.



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Make sure that the front side of the radiator grille is not blocked with anything.


b.

Ask the customer if the front side of the radiator grille was blocked with anything.

Result:
Result Proceed to
Not blocked. A
Is/was blocked. B


HINT:

If the radiator grille is blocked, the inverter coolant temperature will increase and this DTC may be stored.




A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

IF EQUIPPED, EXPLAIN TO CUSTOMER THAT OPTIONAL COVER WILL BE REMOVED

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A93-346 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A02-719 Motor Electronics Coolant Temperature Sensor Circuit Low
P0A03-720 Motor Electronics Coolant Temperature Sensor Circuit High
P0C73-776 Motor Electronics Coolant Pump "A" Control Performance
P314A-828 Inverter Coolant Pump Speed Signal

HINT:

P0A93-346 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.



e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK QUANTITY OF HV COOLANT

NG

CONNECT SECURELY

4.CHECK QUANTITY OF HV COOLANT

A

5.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR HV COOLANT LEAK AND ADD HV COOLANT

5.CHECK COOLANT HOSE

OK

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)

NG

CORRECT THE PROBLEM

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)

OK

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)

NG

7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.


d.

Select Inverter W/P Revolution in the Data List.


e.

While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.

Result:
Tester Display Switch Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 2250 to 5625 rpm


HINT:

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).



f.

Turn the power switch off.



OK

8.READ VALUE USING INTELLIGENT TESTER (DATA LIST)

NG

11.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
8.READ VALUE USING INTELLIGENT TESTER (DATA LIST)
a.

Turn the power switch off and leave the vehicle for at least 1 hour.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Coolant Water Temperature, Inverter Temp (MG2), Cnv Tmp (Upper), Cnv Temp (Lower), Inverter Temp (MG1).


e.

Read the Data List.

Result:
Result Proceed to
Other than below. A
"Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 20°C (36°F) or more. B


NOTICE:

The lower limit temperature that can be displayed for "Inverter Temp (MG1)", "Inverter Temp (MG2)", "Cnv Tmp (Upper)" and "Cnv Temp (Lower)" is 15°C (59°F). The lower limit temperature for "Inverter Coolant Water Temperature" is -40°C (-40°F). The "Inverter Coolant Water Temperature" value displayed on the intelligent tester may be lower than the others, but this is not a malfunction.



f.

Turn the power switch off.



A

9.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

9.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

A

10.REPLACE HV COOLANT

B

10.REPLACE HV COOLANT
11.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

12.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

12.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

OK

14.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)

OK

15.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

OK

16.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

NG

16.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

OK

NG