Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A7A-122  Generator Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

If the generator inverter overheats, has a circuit malfunction, or has an internal short, the inverter transmits this information to the MG ECU via the generator inverter fail signal line.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A7A 122 Generator inverter fail signal detection (overcurrent due to system malfunction)
·

Power management control ECU

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Wire harness or connector

·

PCU fuse



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A1A-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200).

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P324E-788 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P324E-788).

Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 5 seconds or more.

2.

Drive the vehicle for approximately 10 minutes mainly using the engine.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A7A-122 is set before any of the DTCs in the table below are set. A
Any of the DTCs including pending DTCs in the table 1 below are set before P0A7A-122 is set. B
Any of the DTCs in the table 2 below are set before P0A7A-122 is set. C


Table 1
DTC No. Relevant Diagnosis
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P3004-803 High Voltage Power Resource

Table 2
DTC No. Relevant Diagnosis
P3011-123, P3012-123, P3013-123, P0314-123, P3015-123, P3016-123, P0317-123, P3018-123, P3019-123, P3020-123 Battery Block # Becomes Weak
P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance
P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low
P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range/Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AC6-123 Hybrid Battery Temperature Sensor "B" Range/Performance
P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low
P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High
P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance
P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low
P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P3065-123 Hybrid Battery Temperature Sensor Range/Performance Stuck "A"
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

HINT:
·

Refer to the Freeze Frame data to determine the order in which the DTCs were set.

·

P0A7A-122 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

C

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A7A-203 is not output. A
P0A7A-203 is also output. B


NOTICE:
·

If P0A7A-203 is output, troubleshoot it first. After completing the troubleshooting for P0A7A-203, return to perform troubleshooting for this DTC.

·

Parts repaired or replaced during troubleshooting for P0A7A-203 do not need to be re-inspected in this diagnosis procedure.




e.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (HYBRID CONTROL)

B

3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

HINT:
·

If P0A7A-203 was not output in step 2 of this diagnosis procedure, check Table 1 below.

·

If P0A7A-203 was output in step 2 of this diagnosis procedure, repair that DTC first, then check Table 2 below.



Result:
Result Proceed to
Only P0A7A-122 is output, or DTCs other than the ones in the table below are also output. A
Any of the DTCs including pending DTCs are also output. B


Table 1
DTC No. Relevant Diagnosis
P0A1A (all INF codes)*1 Generator Control Module
P0A1B (all INF codes)*1 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
P0A72 (all INF codes)*1 Generator Phase V Current
P0A75 (all INF codes)*1 Generator Phase W Current
P0A78-266, 267, 279, 287, 306, 503, 504, 505, 506, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
P0A7A-325, 344, 517, 518, 809, 810, 811 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0A94-442, 547, 548, 549, 554, 555, 556, 585, 587, 589, 590 DC/DC Converter Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P3004-803 High Voltage Power Resource

Table 2
DTC No. Relevant Diagnosis
P0A1A (all INF codes)*1 Generator Control Module
P0A1B (all INF codes)*1 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
P0A72-333 Generator Phase V Current
P0A75-341 Generator Phase W Current
P0A78-266, 267, 279, 287, 306, 503, 504, 505, 506, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
P0A7A-325, 517, 518, 809, 810, 811 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A94-442, 547, 548, 549, 554, 555, 556, 585, 587, 589, 590 DC/DC Converter Performance
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P3004-803 High Voltage Power Resource

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A7A-122 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

6.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK GENERATOR RESOLVER

OK

7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

21.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

8.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK MOTOR RESOLVER

OK

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

NG

23.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

A

10.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

10.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

A

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

12.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

28.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)
12.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

13.CHECK FUSE (PCU)

NG

30.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)
13.CHECK FUSE (PCU)

OK

14.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

25.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
14.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

OK

15.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

15.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

OK

16.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK POWER MANAGEMENT CONTROL ECU

OK

17.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

17.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

18.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

18.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

19.CHECK FOR INTERMITTENT PROBLEMS

NG

CONNECT SECURELY

19.CHECK FOR INTERMITTENT PROBLEMS

OK

20.SIMULATION TEST

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

20.SIMULATION TEST
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY) and wait for 5 seconds or more.


c.

Drive the vehicle for approximately 10 minutes mainly using the engine.


d.

Enter the following menus: Powertrain / Hybrid Control / DTC.


e.

Check if DTCs are output.

Result:
Result Proceed to
P0A7A-122 is output. A
P0A7A-122 is not output. B


HINT:

If the connector engagement check and cleaning caused the condition to return to normal, DTCs will not be output.



f.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

END

21.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

22.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

NG

CONNECT SECURELY

22.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

23.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

24.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

NG

CONNECT SECURELY

24.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

25.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)

OK

26.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

27.REPAIR OR REPLACE HARNESS OR CONNECTOR
26.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

REPLACE FUSE (PCU)

27.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (PCU)

28.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1) CONNECTION CONDITION)

A

29.CHECK MOTOR CABLE (FOR MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

30.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2) CONNECTION CONDITION)

A

31.CHECK MOTOR CABLE (FOR MG2)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY