Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C73-776  Motor Electronics Coolant Pump "A" Control Performance  


DESCRIPTION

The water pump with motor assembly transmits rotation speed information to the power management control ECU (HV CPU). The power management control ECU (HV CPU) monitors the speed and detects malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P0C73 776 A speed or intermittent stop malfunction occurs in the inverter water pump assembly.
A revolution malfunction (speed is too high/low or stop) or an intermittent stop malfunction (operation stops intermittently when the revolution speed is abnormal) occurs in the inverter water pump assembly.
·

Inverter cooling system

·

Wire harness or connector

·

Inverter water pump assembly

·

Power management control ECU



HINT:

The inverter water pump assembly operates when the power switch is on (READY).


Related Data List
DTC No. INF Code Data List Item
P0C73 776
·

W/P Run Control Duty*1

·

Inverter W/P Revolution

·

Ready signal



*1: The inverter water pump assembly operates when the power switch is on (READY).


Related Active Test
DTC No. INF Code Active Test
P0C73 776 Activate the Water Pump*1

*1: This is an Active Test of the inverter water pump assembly.


WIRING DIAGRAM

A264130E09
1.406,3.302 1.833,3.49 0.427,0.188 10 false IGCT 0.271,2.75 1.021,2.938 0.75,0.188 10 false IGCT-MAIN 5.469,1.01 5.813,1.177 0.344,0.167 10 false IWP 4.271,0.99 4.615,1.156 0.344,0.167 10 false SWP 4.26,1.427 4.615,1.594 0.354,0.167 10 false NWP 3.552,1.427 3.896,1.594 0.344,0.167 10 false GND 3.552,1.01 3.969,1.177 0.417,0.167 10 false +BWP 5.469,1.458 5.917,1.625 0.448,0.167 10 false NIWP 5.469,2.979 5.917,3.146 0.448,0.167 10 false MREL 5.104,1 5.375,1.177 0.271,0.177 10 false A38 5.104,1.438 5.375,1.615 0.271,0.177 10 false A38 5.104,2.979 5.375,3.156 0.271,0.177 10 false A39 5.156,0.792 5.354,0.969 0.198,0.177 10 false 13 5.156,1.24 5.354,1.417 0.198,0.177 10 false 14 5.188,2.771 5.323,2.948 0.135,0.177 10 false 6 5.333,3.927 6.635,4.292 1.302,0.365 10 false Power Management Control ECU 4.688,0.885 4.823,1.063 0.135,0.177 10 false 3 4.688,1.333 4.823,1.51 0.135,0.177 10 false 2 3.375,0.906 3.51,1.083 0.135,0.177 10 false 4 3.375,1.313 3.51,1.49 0.135,0.177 10 false 1 3.604,1.906 4.708,2.281 1.104,0.375 10 false Inverter Water Pump Assembly 3.604,1.76 3.948,1.927 0.344,0.167 10 false A53 1.938,2.479 2.073,2.656 0.135,0.177 10 false 5 1.938,2.865 2.073,3.042 0.135,0.177 10 false 1 1.167,2.479 1.302,2.656 0.135,0.177 10 false 3 1.156,2.865 1.292,3.042 0.135,0.177 10 false 2 2.521,2 3.302,2.458 0.781,0.458 10 false IGCT NO. 3 5.49,3.458 5.833,3.625 0.344,0.167 10 false E1 5.198,3.26 5.333,3.438 0.135,0.177 10 false 6 5.104,3.469 5.396,3.646 0.292,0.177 10 false G57 2.229,1.813 2.365,1.99 0.135,0.177 10 false 2 2.229,2.135 2.365,2.313 0.135,0.177 10 false 1 0.26,3.75 3.646,4 3.385,0.25 10 false IWP: Inverter water pump assembly drive duty 0.25,4.115 3.635,4.365 3.385,0.25 10 false NIWP: Inverter water pump assembly speed signal

CAUTION / NOTICE / HINT

HINT:
·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (READY) and wait for 2 minutes or more.


·

If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the inverter water pump assembly may suspend control as a self-protection function and store DTC.

(When the auxiliary battery voltage returns to normal, the inverter water pump assembly will resume normal operation. In this case it is not necessary to replace the inverter water pump assembly.)



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:
·

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.

·

When the inverter water pump assembly operation command line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter W/P Revolution.


d.

Read the Data List.

Result:
Tester Display Switch Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 625 rpm or less


HINT:

When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" displays a value lower than 625 rpm.



e.

Turn the power switch off.



OK

2.CLEAR DTC

NG

5.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
2.CLEAR DTC

NEXT

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.


d.

Select Inverter W/P Revolution in the Data List.


e.

While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.

Result:
Tester Display Switch Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 2250 to 5625 rpm


HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" displays a value lower than 625 rpm.




f.

Turn the power switch off.



OK

4.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

5.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
4.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

A

11.REPLACE INVERTER WATER PUMP ASSEMBLY

B

REPLACE HV COOLANT

5.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

6.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
a.
A267464

Check the connector connections and contact pressure of the relevant terminals for the inverter water pump assembly connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect connector A38 from the power management control ECU.


b.

Disconnect connector A53 from the inverter water pump assembly.


c.

Measure the resistance according to the value(s) in the table below.

U158963E02
1.385,1.865 1.76,2.198 false 5.344,1.542 5.292,1.917 false 1.792,2.125 2.115,2.313 0.323,0.188 10 false IWP 5.104,1.948 5.5,2.135 0.396,0.188 10 false SWP 0.417,0.229 0.615,0.417 0.198,0.188 10 false *a 4.385,0.229 4.583,0.417 0.198,0.188 10 false *b 1.854,1.771 2.125,1.938 0.271,0.167 10 false A38 5.969,1.448 6.24,1.615 0.271,0.167 10 false A53

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A53-3 (SWP) - A38-13 (IWP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A53-3 (SWP) or A38-13 (IWP) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Connect the power management control ECU connector.


e.

Connect the inverter water pump assembly connector.



OK

8.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING INTELLIGENT TESTER (INVERTER W/P REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the intelligent tester to the DLC3.


b.

Remove the IGCT No. 3 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / ECU Data List / Inverter W/P Revolution.


e.

Read the Data List.

Result:
Tester Display Switch Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 125 rpm or less



f.

Turn the power switch off.


g.

Install the IGCT No. 3 fuse.



OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect connector A38 from the power management control ECU.


b.

Turn the power switch on (IG).


c.
U158836E02
0.792,2.438 1.302,2.583 false 1.833,1.396 2.094,2.094 false 0.76,2.99 1.031,3.156 0.271,0.167 10 false A38 1.333,2.521 1.656,2.688 0.323,0.167 10 false IWP 0.26,0.271 0.417,0.438 0.156,0.167 10 false *a 2.115,2.021 2.438,2.188 0.323,0.167 10 false E1 1.948,2.292 2.25,2.458 0.302,0.167 10 false G57

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-13 (IWP) - G57-6 (E1) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Connect the power management control ECU connector.



OK

10.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

NG

11.REPLACE INVERTER WATER PUMP ASSEMBLY
10.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Turn the power switch on (IG).


b.
U158919E02
1.823,1.698 2.188,2.365 false 0.781,1.771 1.104,2.375 false 1.906,0.99 2.188,1.156 0.281,0.167 10 false G57 0.656,0.99 0.938,1.156 0.281,0.167 10 false A38 0.177,0.188 0.448,0.354 0.271,0.167 10 false *a 2.125,2.385 2.438,2.552 0.313,0.167 10 false E1 0.979,2.385 1.292,2.552 0.313,0.167 10 false IWP

While turning the power switch on (IG), check the waveform between the power management control ECU terminals.

Item Content
Terminal A38-13 (IWP) - G57-6 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Power switch on (IG)

Text in Illustration
*a Component with Harness Connected
(Power Management Control ECU)

OK:

Waveform duty ratio is between 3% and 9%.



c.

Turn the power switch off.



OK

11.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

11.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

12.ADD HV COOLANT AND PERFORM AIR BLEEDING
12.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COOLANT(for Inverter)>REPLACEMENT



NEXT

COMPLETED