Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277925 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AAE-123  Hybrid Battery Pack Air Temperature Sensor "A" Circuit Low  P0AAF-123  Hybrid Battery Pack Air Temperature Sensor "A" Circuit High  


DESCRIPTION

The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensor (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123). The battery smart unit uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.


DTC No. INF Code DTC Detection Condition Trouble Area
P0AAE
P0AAF
123 When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open circuit) or is higher than a predetermined limit (short circuit)
·

Hybrid battery thermistor

·

Battery smart unit

·

Wire harness or connector



HINT:

After confirming that DTC P0AAE-123 or P0AAF-123 is output, use the intelligent tester to check "Inhaling Air Temp" in the HV ECU data list.


Displayed Temperature Malfunction
-45 °C (-49 °F) or less Open or +B short circuit
95 °C (203 °F) or more GND short

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9C-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK FOR DTCS (HV)

A

2.CHECK CONNECTOR CONNECTION CONDITION

B

2.CHECK CONNECTOR CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.
A389836E01
1.323,1.854 1.635,2.073 0.313,0.219 1.417,1.885 1.729,2.083 0.313,0.198 10 false d1

Check the connections of the d1 connector of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.



d.

Install the No. 1 hybrid battery shield sub-assembly.



OK

3.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR

NG

CONNECT SECURELY

3.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A267373

Visually check the installation condition of the inlet air temperature sensor.

OK:

The inlet air temperature sensor is installed in the correct location and its claws are engaged securely.


Result:
Result Proceed to
The inlet air temperature sensor is installed in the correct location and its claws are engaged securely A
Claws are damaged. B
Inlet air temperature sensor is not installed correctly, but claws are not damaged. C



d.

Install the No. 2 hybrid battery shield sub-assembly.



A

4.CHECK HYBRID BATTERY THERMISTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)

B

C

INSTALL PARTS CORRECTLY

4.CHECK HYBRID BATTERY THERMISTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.

Disconnect connectors M39 and d1 from the battery smart unit.


d.
U158906E03
1.563,2.313 1.135,2.25 false 2.042,4.365 1.896,4.115 false 2.531,3.563 1.896,3.979 false 2.396,3.313 1.792,3.979 false 1.083,3.958 1.646,3.979 false 1.156,4.313 1.646,4.135 false 1.365,4.396 1.771,4.135 false 2.521,3.885 2.021,4.021 false 2.542,4.167 2.021,4.135 false 1.563,2.448 1.135,2.583 false 0.177,0.125 0.448,0.302 0.271,0.177 10 false *a 0.802,2.167 1.198,2.406 0.396,0.24 10 false IGCT 0.781,3.896 1.125,4.104 0.344,0.208 10 false TBO 2.448,3.146 2.781,3.354 0.333,0.208 10 false TB1 2.594,3.458 3.01,3.708 0.417,0.25 10 false TB2 0.792,4.26 1.146,4.458 0.354,0.198 10 false GBO 1.167,4.417 1.5,4.604 0.333,0.188 10 false GB1 1.969,4.385 2.281,4.563 0.313,0.177 10 false GB2 2.583,3.792 2.958,3.979 0.375,0.188 10 false TCO 2.594,4.083 2.969,4.292 0.375,0.208 10 false GCO 0.885,1.677 1.396,1.958 0.51,0.281 10 false M39 0.667,3.469 0.958,3.688 0.292,0.219 10 false d1 0.813,2.531 1.208,2.771 0.396,0.24 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (TCO) - d1-7 (GCO) 0°C (32°F) 26.7 to 27.8 kΩ
25°C (77°F) 9.9 to 10.1 kΩ
40°C (104°F) 5.73 to 5.92 kΩ


Text in Illustration
*a Rear view of wire harness connector
(to Battery Smart Unit)


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
d1-1 (TCO) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-1 (TCO) - M39-6 (GND) Power switch off 10 kΩ or higher
d1-7 (GCO) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-7 (GCO) - M39-6 (GND) Power switch off 10 kΩ or higher
d1-4 (TBO) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-4 (TBO) - M39-6 (GND) Power switch off 10 kΩ or higher
d1-10 (GBO) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-10 (GBO) - M39-6 (GND) Power switch off 10 kΩ or higher
d1-3 (TB1) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-3 (TB1) - M39-6 (GND) Power switch off 10 kΩ or higher
d1-9 (GB1) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-9 (GB1) - M39-6 (GND) Power switch off 10 kΩ or higher
d1-2 (TB2) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-2 (TB2) - M39-6 (GND) Power switch off 10 kΩ or higher
d1-8 (GB2) - M39-3 (IGCT) Power switch off 10 kΩ or higher
d1-8 (GB2) - M39-6 (GND) Power switch off 10 kΩ or higher



f.

Connect the battery smart unit connectors.


g.

Install the No. 1 hybrid battery shield sub-assembly.



OK

NG

5.CHECK HARNESS AND CONNECTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper hybrid battery cover sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Check the wire harness and connectors of the battery temperature sensor and inlet air temperature sensor for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.



d.

Install the upper hybrid battery cover sub-assembly.



OK

NG

REPAIR HARNESS OR CONNECTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)