Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277928 HV BATTERY A

HYBRID / BATTERY CONTROL  HV BATTERY  REMOVAL  


PROCEDURE

Hide 2.CHECK FOR DTCS

a.

Check for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).

NOTICE:

Confirm that P0AA6 (Hybrid Battery Voltage System Isolation Fault) is not output before removing or installing the HV battery. If this DTC is output, perform troubleshooting for this DTC first.



Hide 71033 5.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92F1 11.REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT

Hide G9230 12.REMOVE BATTERY COOLING BLOWER ASSEMBLY

NOTICE:
·

Be sure not to touch the fan part of the battery cooling blower assemblies.

·

Do not lift the battery cooling blower assemblies using the wire harness.



a.
A266759

Disconnect the battery cooling blower assembly connector and clamp.


b.
A266760

Remove the 2 bolts, nut and battery cooling blower assembly.


Hide G92N1A 13.REMOVE NO. 1 HYBRID VEHICLE BATTERY COVER PANEL LH

Hide 15.REMOVE WIRE HARNESS

a.
A266758

Disconnect the 2 connectors and 3 clamps as shown in the illustration.


b.
A266763

Disconnect the connector as shown in the illustration.


Hide G9510 17.REMOVE HV BATTERY

CAUTION:

Wear insulating gloves.


NOTICE:

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.


a.
A266765

Remove the 2 clips.


b.
A266766

Remove the 2 bolts and 2 nuts.


c.
A267090E02
0.708,0.448 1.563,0.792 true 1.26,0.375 1.604,0.719 true 1.958,0.365 1.729,0.729 true 2.552,0.448 1.76,0.792 true 1.531,2.125 1.844,2.292 false 1.708,4.083 2.125,4.208 false 2.469,3.948 2.323,4.208 false 1.583,0.74 1.76,0.958 0.177,0.219 10 false *a 1.854,2.198 2.031,2.417 0.177,0.219 10 false *a 2.167,4.135 2.344,4.354 0.177,0.219 10 false *b

Remove the HV battery.

Text in Illustration
*a Area A
*b Attachment

NOTICE:
·

When moving the HV battery, be sure to hold area A shown in the illustration.

·

Place the HV battery on the attachment.




Hide G92T9 18.REMOVE HYBRID BATTERY SERVICE PLUG COVER

Hide G920Q 19.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G920C 20.REMOVE NO. 2 HYBRID VEHICLE BATTERY CARRIER BRACKET SUB-ASSEMBLY

Hide G920R 22.REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Wear insulating gloves.


a.
A266775

Remove the 2 bolts, nut and No. 2 hybrid battery shield sub-assembly.


Hide G92Z0 23.REMOVE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

Hide G92E1 24.REMOVE NO. 1 HYBRID BATTERY COVER INTAKE DUCT

CAUTION:

Wear insulating gloves.


a.
A267085

Disconnect the HV battery thermistor.


b.

Remove the clip and No. 1 hybrid battery cover intake duct.


Hide G920N 25.REMOVE UPPER HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A267087

Remove the 5 nuts and upper hybrid battery cover sub-assembly.


Hide G92J5 26.DISCONNECT NO. 1 HYBRID BATTERY PACKING

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A267088

Disconnect the 2 clamps.


b.
A267089

Disconnect the 2 wire harnesses and remove the No. 1 hybrid battery packing.