Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT › 2011.12–2014.12
RM2170E _52 Drivetrain _057015 AXLE AND DIFFERENTIAL _0277998 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:
·

When the brake pedal is first depressed after replacing the brake shoes or pushing back the wheel brake cylinder piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake shoes are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE REAR WHEEL

Hide 42403 4.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

Hide 42312E 5.REMOVE REAR AXLE HUB BOLT

a.
C249954E02
1.313,1.5 1.313,1.969 false 1.208,0.865 1.052,0.865 true 1.979,1.396 2.5,1.396 false 1.219,1.958 1.438,2.135 0.219,0.177 10 true *1 0.875,0.792 1.052,0.958 0.177,0.167 10 true *1 2.51,1.313 2.833,1.469 0.323,0.156 10 false SST

Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Text in Illustration
*1 Service Nut

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 6.INSTALL REAR AXLE HUB BOLT

a.
C249955E02
0.802,0.74 0.802,0.219 0.802,0.219 0.875,0.219 true 0.521,0.615 0.521,0.208 0.521,0.208 0.417,0.208 true 0.24,0.125 0.396,0.271 0.156,0.146 10 false *2 0.896,0.146 1.115,0.344 0.219,0.198 10 true *1

Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.

Text in Illustration
*1 Service Nut
*2 Washer


b.

Install a washer and service nut to the new rear axle hub bolt as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42403 7.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

Hide 8.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>1NZ-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION).


b.

Connect the reservoir level switch connector.