Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2015.11
RM2170E _52 Drivetrain _057015 AXLE AND DIFFERENTIAL _0278002 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502E 1.INSTALL FRONT AXLE HUB BEARING

a.
C249888E01
2.543,2.778 1.802,2.778 1.802,2.778 2.438,3.355 false 1.441,2.695 1.735,2.845 0.294,0.150 10 SST

Using SST and a press, insert a new front axle hub bearing, with its magnetic rotor side facing the inside of the vehicle, until it reaches the end of the steering knuckle.

SST
09950-60020  (09951-00720)
09950-70010  (09951-07100)

Text in Illustration
V100135

Inside of the Vehicle
V100145

Magnetic Rotor Side

NOTICE:
·

Do not remove the inner race because the hub bearing is built into the oil seal.

·

Do not use bearings that have been removed.

·

Do not wipe off any grease that has been applied to new bearings.

·

Do not bring magnets close to the magnetic rotor surface of the bearing.

·

Keep the magnetic rotor surface of the bearing free of foreign matter.




Hide 43502C 2.INSTALL FRONT AXLE HUB SUB-ASSEMBLY

a.
C107983E05
0.948,1.833 0.948,1.74 false 0.875,0.917 0.635,0.771 0.635,0.771 0.802,1.146 true 0.313,0.656 0.677,0.823 0.365,0.167 10 false SST 0.813,1.865 1.177,2.031 0.365,0.167 10 true SST

Using SST and a press, press the axle hub into the steering knuckle.

SST
09608-32010  
09950-60010  (09951-00530)
09950-70010  (09951-07100)


Hide 43502G 3.INSTALL FRONT AXLE HUB HOLE SNAP RING

a.
C202605E05
2.417,1.677 2.594,1.854 0.177,0.177 10 false *a

Using snap ring pliers, install a new front axle hub hole snap ring, as shown in the illustration.

Text in Illustration
*a Speed Sensor Installation Gap

NOTICE:
·

Do not overlap the end of the snap ring and the installation hole in the front speed sensor on the steering knuckle side.

·

Do not damage the magnetic rotor surface of the bearing when installing the snap ring.




Hide 4.INSTALL FRONT AXLE ASSEMBLY

a.

Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

NOTICE:

When installing the nuts, keep the bolts from rotating.


HINT:

The bolt can be inserted in either direction, however, make sure that they are installed in the same direction.



Hide 43420 5.INSTALL FRONT DRIVE SHAFT ASSEMBLY

a.
C249882E02
2.875,0.719 2.563,0.719 2.563,0.719 2.563,1.646 true 3.052,1.083 2.563,1.083 true 2.479,1.667 2.635,1.823 0.156,0.156 10 false *a

Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and install the front drive shaft assembly to the front axle hub sub-assembly.

Text in Illustration
*a Matchmark

NOTICE:

Be careful not to damage the drive shaft boot or speed sensor rotor.



Hide 48069 6.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 45047 7.CONNECT TIE ROD END SUB-ASSEMBLY

Hide 9.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43502H 10.TEMPORARILY INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using a non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new drive shaft.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a socket wrench (30 mm), while applying the brakes, temporarily install the front axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

NOTICE:

Stake the front axle shaft nut after inspecting for looseness and runout in the following steps.


HINT:

Keep depressing the brake pedal to prevent the drive shaft from rotating.



Hide 11.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 12.REMOVE FRONT DISC

Hide 13.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 43512 15.INSTALL FRONT DISC

Hide 16.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 89543 17.INSTALL FRONT SPEED SENSOR

a.

Install the front speed sensor wire and front flexible hose to the front shock absorber assembly with the bolt.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Do not twist the front speed sensor and front flexible hose when installing it.



b.

Install the front speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.



Hide 43502H 18.INSTALL FRONT AXLE SHAFT NUT

a.
C249883

Using a chisel and hammer, stake the front axle shaft nut.


Hide 19.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 20.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>1NZ-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION).


b.

Connect the reservoir level switch connector.



Hide 21.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT