Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › 2011.12–2014.12
RM2170E _53 Suspension _057018 REAR SUSPENSION _0278013 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  INSTALLATION  


PROCEDURE

Hide 48258C 1.INSTALL REAR LOWER COIL SPRING INSULATOR LH

a.

Install the rear lower coil spring insulator LH onto the rear axle beam assembly.


Hide 48258B 2.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as the LH side.


Hide 48259A 3.INSTALL REAR UPPER COIL SPRING INSULATOR LH

a.
C354547E01
2.323,0.5 2.635,0.698 0.313,0.198 10 false *a

Install the rear upper coil spring insulator LH so that its gap fits onto the end of rear coil spring LH.

Text in Illustration
*a Fit


Hide 48257C 4.INSTALL REAR UPPER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as the LH side.


Hide 48231B 5.INSTALL REAR COIL SPRING LH

a.

Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.


b.

Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Since stopper nuts are used, turn the bolts.



c.

Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.


d.
C233115

Install the rear coil spring LH onto the rear axle beam assembly.

Text in Illustration
V100144

Paint Mark

NOTICE:

The paint mark of the rear coil spring LH should be towards the underside and rear side of the vehicle.



e.

Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily install the rear axle beam assembly and rear coil spring LH with the 2 bolts and 2 nuts.


Hide 48231A 6.INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as the LH side.


Hide 47319F 7.INSTALL REAR FLEXIBLE HOSE LH

a.

Install the rear flexible hose LH onto the rear axle beam assembly with a new clip.

NOTICE:

Install the clip as far as it will go.



b.

Using a union nut wrench, install the rear flexible hose LH to the brake tube while holding the rear flexible hose LH with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 47318F 8.INSTALL REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as the LH side.


Hide 89516D 9.INSTALL SKID CONTROL SENSOR WIRE LH

a.

Install the skid control sensor wire LH to the rear axle beam assembly with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 89516C 10.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 89516C 12.CONNECT SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 13.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 42110F 15.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY

Hide 48540 16.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 17.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 18.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 19.BLEED BRAKE LINE

Hide 89407A 20.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)