Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2014.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.

WIRING DIAGRAM

C212028E29
5.969,0.719 6.365,0.875 0.396,0.156 10 false CA1L 5.698,0.583 5.979,0.74 0.281,0.156 10 false 38 5.698,1.49 5.885,1.646 0.188,0.156 10 false 37 4.198,0.469 4.385,0.625 0.188,0.156 10 false 24 4.198,1.396 4.385,1.552 0.188,0.156 10 false 25 2.948,0.938 3.135,1.094 0.188,0.156 10 false 11 5.969,1.635 6.385,1.792 0.417,0.156 10 false CA1H 3.635,0.719 4.031,0.875 0.396,0.156 10 false CA1L 3.615,1.635 4.031,1.792 0.417,0.156 10 false CA1H 0.948,1.188 1.156,1.344 0.208,0.156 10 false TC 3.302,1.208 3.51,1.365 0.208,0.156 10 false TC 1.25,1.031 1.427,1.188 0.177,0.156 10 false 13 1.25,2.969 1.354,3.125 0.104,0.156 10 false 4 0.948,3.104 1.188,3.26 0.24,0.156 10 false CG 0.479,4.146 0.698,4.302 0.219,0.156 10 false G4 0.729,4.146 1.115,4.302 0.385,0.156 10 false DLC3 3.052,4.135 4.354,4.51 1.302,0.375 10 false Power Management Control ECU 5,4.146 7.104,4.51 2.104,0.365 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.125,0.729 4.427,0.885 0.302,0.156 10 false G58 4.125,1.635 4.469,1.792 0.344,0.156 10 false G58 2.875,1.188 3.198,1.344 0.323,0.156 10 false G57 5.969,2.615 6.365,2.771 0.396,0.156 10 false CA2L 5.698,2.479 5.885,2.635 0.188,0.156 10 false 34 5.698,3.406 5.885,3.563 0.188,0.156 10 false 35 4.188,2.365 4.375,2.521 0.188,0.156 10 false 30 4.208,3.302 4.396,3.458 0.188,0.156 10 false 31 5.969,3.552 6.385,3.708 0.417,0.156 10 false CA2H 3.625,2.615 4.021,2.771 0.396,0.156 10 false CA3N 3.635,3.542 4.052,3.698 0.417,0.156 10 false CA3P 4.125,2.615 4.427,2.771 0.302,0.156 10 false G58 4.135,3.552 4.479,3.708 0.344,0.156 10 false G58 4.688,4.146 4.99,4.302 0.302,0.156 10 false A41

HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - POWER MANAGEMENT CONTROL ECU)

B

2.CHECK HARNESS AND CONNECTOR (TC of DLC3 - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-13 (TC) - G57-11 (TC) Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
U183512E02
1.646,1.958 2.375,1.01 false 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 2.323,0.833 2.563,1 0.24,0.167 10 false CG 0.302,1.042 0.521,1.188 0.219,0.146 10 false G4

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-4 (CG) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of DLC3



OK

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - BODY GROUND)
a.
U183513E01
0.263,0.249 0.446,0.419 0.184,0.170 10 *a 2.48,0.811 2.719,0.980 0.239,0.170 10 TC 0.315,1.039 0.570,1.190 0.256,0.151 10 G4 1.875,2.449 2.603,1.014 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-13 (TC) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of DLC3

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE WIRE HARNESS OR EACH ECU