If a malfunction is detected in the power supply circuit, the skid control ECU power source voltage drops, or there is insufficient voltage to operate the ABS main relay, the skid control ECU will store these DTCs.
These DTCs may also be stored if the auxiliary battery voltage drops below 9.5 V.
DTC C1256/56 (Accumulator Low Pressure) may also be memorized if there is a drop in power source voltage.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1241/41 | 101 | Any of the following conditions when the BS terminal voltage is 9.3 V or less:
1.
Vehicle not decelerated (brake pedal is not depressed) for 3 seconds or more. 2.
While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A. 3.
Vehicle decelerated (brake pedal is depressed) for 0.06 seconds. |
·
Improperly connected connector, deformation or corrosion of terminals ·
Auxiliary battery ·
Hybrid control system (Charging circuit) ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 102 | Either of the following conditions when the ECU internal voltage is 6.3 V or less:
1.
When main relay ON is requested, voltage of the relay connection does not exceed 3.5 V for 0.22 seconds or more. 2.
Sensor supply voltage is 4.75 V or less, or 5.25 V or more for 0.06 seconds. 3.
Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more for 0.06 seconds. |
↑ |
| ↑ | 551 | When driving at 3 km/h (1.9 mph) or more, IG1 terminal voltage is 9.5 V or less, or VM1 voltage is 8.6 V or less for 10 seconds or more. | ↑ |
| ↑ | 552 | When VM1 voltage is 8.6 V or less, sensor supply voltage is low for 60 seconds or more. | ↑ |
| ↑ | 553 | VM1 voltage is 16.6 V or more for 0.8 seconds. | ↑ |
| C1242/42 | 111 | Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more) for 4 seconds or more. | ·
Open or short in IG1 circuit ·
Improperly connected connector, deformation or corrosion of terminals ·
Smart entry and start system (IG start circuit) ·
Auxiliary battery ·
Hybrid control system (Charging circuit) ·
Skid control ECU (Brake booster with master cylinder assembly) |
| ↑ | 112 | Voltage is not applied to the IG2 terminal (less than 3.5 V), and applied to the IG1 terminal (9.5 V or more) for 4 seconds or more. | ·
Open or short in IG2 circuit ·
Improperly connected connector, deformation or corrosion of terminals ·
Smart entry and start system (IG start circuit) ·
Auxiliary battery ·
Hybrid control system (Charging circuit) ·
Skid control ECU (Brake booster with master cylinder assembly) |
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Check if smart entry and start system (for start function) DTCs are output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output. | A |
| DTC is output. | B |
A
B
Check if hybrid control system DTCs are output (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output. | A |
| DTC is output. | B |
A
B
Check that no main relay DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Main relay malfunction DTC is not output. | A |
| Main relay malfunction DTC is output. | B |
A
B
Check the auxiliary battery voltage.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery | Power switch on (IG) | 11 to 14 V |
| Auxiliary battery | Power switch on (ready) | 11 to 15.5 V |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-14 (BI) - Body ground | Always | 11 to 14 V |
| A41-15 (BS) - Body ground | Always | 11 to 14 V |
| A41-16 (IG1) - Body ground | Power switch on (IG) | 11 to 14 V |
| A41-12 (IG2) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
OK
NG
Turn the power switch off (lock).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-28 (GND) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A41-27 (GND2) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A41-26 (GND3) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A41-25 (GND4) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A41-24 (GND5) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A41-23 (GND6) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
OK
NG
Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Perform a road test.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1241/41 and C1242/42 are not output. | A |
| DTCs C1241/41 and/or C1242/42 are output (for LHD). | B |
| DTCs C1241/41 and/or C1242/42 are output (for RHD). | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C