Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2014.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1203/95  ECM Communication Circuit Malfunction  


DESCRIPTION

The circuit is used to send TRC and VSC information from the skid control ECU to the hybrid vehicle control ECU, and hybrid control system information from the hybrid vehicle control ECU to the skid control ECU via the CAN communication system.

Identification information sent from other ECUs is stored when shipped from the factory and used as default values.

NOTICE:

DTC C1203/95 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from that stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.


DTC No. INF Code DTC Detection Condition Trouble Area
C1203/95 - Either of the following is detected:
1.

Identification information sent from other ECUs does not match with the value stored when shipped from the factory.

2.

No stored information for destination.


·

The wrong ECU was installed

·

Skid control ECU (Brake booster with master cylinder assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK PART NUMBER
a.

Check that the proper hybrid vehicle control ECU, main body ECU (multiplex network body ECU) and yaw rate and acceleration sensor (airbag sensor assembly) are installed.

OK:

Proper ECUs are installed.



b.

Check if the hybrid vehicle control ECU, main body ECU (multiplex network body ECU) and yaw rate and acceleration sensor (airbag sensor assembly) were replaced before the DTC was recorded.

OK:

ECU were not replaced.


Result:
Result Proceed to
OK A
NG (A proper hybrid vehicle control ECU is not installed and/or the hybrid vehicle control ECU was replaced.) B
NG (A proper main body ECU (multiplex network body ECU) is not installed and/or the main body ECU (multiplex network body ECU) was replaced.) C
NG (A proper yaw rate and acceleration sensor (airbag sensor assembly) is not installed and/or the yaw rate and acceleration sensor (airbag sensor assembly) was replaced.) D




A

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE

B

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
a.

Perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).

HINT:

Before performing initialization and calibration of the linear solenoid valve, C1203/95 will be output.




NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (IG).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1203/95 is output (for LHD). A
DTC C1203/95 is output (for RHD). B
DTC C1203/95 is not output. C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

END