Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1466/33  Rear Speed Sensor RH Circuit  C1467/34  Rear Speed Sensor LH Circuit  


DESCRIPTION

The speed sensor detects wheel speed and sends signals to the skid control ECU. These signals are used for ABS control.

DTCs C1273/73 and C1274/74 can be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273/73 and C1274/74 are output only in Test Mode.

C354548E01
1.583,0.854 1.583,0.438 1.583,0.438 1.74,0.438 false 1.802,0.354 2.938,0.698 1.135,0.344 10 false Speed Sensor 0.958,2.167 2.583,2.51 1.625,0.344 10 false Speed Sensor Rotor 4.031,2.146 5.365,2.469 1.333,0.323 10 false Low speed 4.99,2.135 5.844,2.427 0.854,0.292 10 false High speed 6.125,1.26 7.156,1.625 1.031,0.365 10 false 1.4 V 6.125,1.615 7.156,1.979 1.031,0.365 10 false 0.7 V

DTC No. INF Code DTC Detection Condition Trouble Area
C1466/33 521 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 522 A malfunction occurs in 2 or more wheels. ↑
↑ 523 An open is detected in the speed sensor signal circuit for 0.05 seconds or more.
·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 524 Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 526 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 527 While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor RH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 528 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


C1467/34 531 While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 532 A malfunction occurs in 2 or more wheels. ↑
↑ 533 An open is detected in the speed sensor signal circuit for 0.05 seconds or more.
·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 534 Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 536 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 537 While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.
·

Open or short in speed sensor

·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Rear speed sensor LH

·

Skid control ECU (Brake booster with master cylinder assembly)


↑ 538 When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.
·

Open or short in wire harness

·

Skid control ECU (Brake booster with master cylinder assembly)


C1273/73
C1274/74
- Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)



HINT:
·

DTCs C1466/33 and C1273/73 are for the rear speed sensor RH.

·

DTCs C1467/34 and C1274/74 are for the rear speed sensor LH.



WIRING DIAGRAM

C220952E20
0.927,1.385 2.448,1.552 1.521,0.167 10 false Rear Speed Sensor RH 2.229,0.875 2.344,1.042 0.115,0.167 10 false 1 1.063,0.875 1.177,1.042 0.115,0.167 10 false 2 0.938,3.365 2.458,3.531 1.521,0.167 10 false Rear Speed Sensor LH 2.229,2.813 2.344,2.979 0.115,0.167 10 false 1 1.063,2.813 1.177,2.979 0.115,0.167 10 false 2 4.99,3.979 7.104,4.365 2.115,0.385 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.771,0.969 5.948,1.115 0.177,0.146 10 false 9 5.979,0.521 6.302,0.667 0.323,0.146 10 false RR+ 5.698,0.406 5.875,0.552 0.177,0.146 10 false 22 5.979,1.094 6.271,1.24 0.292,0.146 10 false RR- 5.771,2.927 6,3.073 0.229,0.146 10 false 7 5.979,2.51 6.333,2.656 0.354,0.146 10 false RL+ 5.698,2.365 5.875,2.51 0.177,0.146 10 false 20 5.979,3.042 6.229,3.188 0.25,0.146 10 false RL- 0.979,1.115 1.271,1.281 0.292,0.167 10 false W1 4.25,1.49 4.917,1.656 0.667,0.167 10 false Shielded 4.25,3.469 4.917,3.635 0.667,0.167 10 false Shielded 4.667,3.979 4.969,4.125 0.302,0.146 10 false A41 1.344,1.115 1.667,1.26 0.323,0.146 10 false RR+ 1.75,1.115 2.042,1.26 0.292,0.146 10 false RR- 1.365,3.083 1.719,3.229 0.354,0.146 10 false RL+ 1.75,3.073 2,3.219 0.25,0.146 10 false RL- 2.99,0.281 3.104,0.448 0.115,0.167 10 false 1 2.99,0.854 3.104,1.021 0.115,0.167 10 false 2 2.177,1.115 2.469,1.281 0.292,0.167 10 false W1 0.677,1.698 2.542,1.865 1.865,0.167 10 false Skid Control Sensor Wire RH 2.875,0.563 3.271,0.729 0.396,0.167 10 false WM1 2.875,1.125 3.271,1.292 0.396,0.167 10 false WM1 1.01,3.073 1.26,3.24 0.25,0.167 10 false X1 2.208,3.073 2.458,3.24 0.25,0.167 10 false X1 0.677,3.635 2.583,3.802 1.906,0.167 10 false Skid Control Sensor Wire LH 2.99,2.24 3.104,2.406 0.115,0.167 10 false 1 2.99,2.813 3.104,2.979 0.115,0.167 10 false 2 2.896,2.5 3.219,2.667 0.323,0.167 10 false XM1 2.885,3.073 3.229,3.24 0.344,0.167 10 false XM1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection / Error or Normal Error: Momentary interruption
Normal: Normal
-

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
a.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


b.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.




OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off (lock).


b.

Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are cleared.




OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1466/33 and C1467/34 are not output. A
DTCs C1466/33 and/or C1467/34 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
5.CHECK REAR SPEED SENSOR INSTALLATION
a.
C144931E19
0.99,1.531 1.198,0.833 1.198,0.833 1.354,0.833 false 0.156,0.115 1.563,0.323 1.406,0.208 10 false Rear Speed Sensor: 1.396,0.74 2.281,0.927 0.885,0.188 10 false No clearance 0.885,2.823 1.146,3.01 0.26,0.188 10 false OK 2.323,2.823 2.583,3.01 0.26,0.188 10 false NG

Turn the power switch off (lock).


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle carrier.




OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)
a.
C354340E01
0.167,0.5 0.583,0.75 0.417,0.25 1.75,0.5 2.167,0.75 0.417,0.25 1.75,2.75 2.167,3 0.417,0.25 0.167,2.75 0.583,3 0.417,0.25 0.583,2.167 0.927,1.292 false 1.5,2.167 1.146,1.292 false 2.917,2.167 2.625,1.375 false 2.167,2.167 2.448,1.396 false 0.583,4.406 0.927,3.531 false 1.49,4.396 1.135,3.521 false 2.167,4.375 2.448,3.604 false 2.917,4.417 2.625,3.625 false 0.104,0.042 0.51,0.479 0.406,0.438 10 false *a 0.115,0.25 0.427,0.448 0.313,0.198 10 false *A 0.271,0.542 0.583,0.74 0.313,0.198 10 false W1 0.885,0.583 1.198,0.781 0.313,0.198 10 false *b 2.417,0.594 2.729,0.792 0.313,0.198 10 false *c 1.792,0.542 2.292,0.854 0.5,0.313 10 false WM1 1.406,2.198 1.802,2.438 0.396,0.24 10 false RR+ 0.302,2.792 0.615,2.99 0.313,0.198 10 false X1 1.823,2.792 2.229,3.042 0.406,0.25 10 false XM1 0.135,2.448 0.448,2.646 0.313,0.198 10 false *B 0.917,2.833 1.229,3.031 0.313,0.198 10 false *b 2.438,2.833 2.75,3.031 0.313,0.198 10 false *c 0.438,4.427 0.823,4.667 0.385,0.24 10 false RL- 1.385,4.427 1.771,4.667 0.385,0.24 10 false RL+ 2.01,4.427 2.396,4.667 0.385,0.24 10 false RL+ 2.823,4.427 3.208,4.667 0.385,0.24 10 false RL- 0.448,2.198 0.844,2.438 0.396,0.24 10 false RR- 2,2.198 2.396,2.438 0.396,0.24 10 false RR+ 2.802,2.188 3.198,2.427 0.396,0.24 10 false RR-

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the rear speed sensor connector and the skid control sensor wire.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
W1-2 (RR+) - WM1-1 (RR+) Always Below 1 Ω
W1-2 (RR+) - WM1-2 (RR-) Always 10 kΩ or higher
W1-2 (RR+) - Body ground Always 10 kΩ or higher
W1-1 (RR-) - WM1-2 (RR-) Always Below 1 Ω
W1-1 (RR-) - WM1-1 (RR+) Always 10 kΩ or higher
W1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
X1-2 (RL+) - XM1-1 (RL+) Always Below 1 Ω
X1-2 (RL+) - XM1-2 (RL-) Always 10 kΩ or higher
X1-2 (RL+) - Body ground Always 10 kΩ or higher
X1-1 (RL-) - XM1-2 (RL-) Always Below 1 Ω
X1-1 (RL-) - XM1-1 (RL+) Always 10 kΩ or higher
X1-1 (RL-) - Body ground Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Front view of skid control sensor wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)

NG

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A41-22 (RR+) - WM1-1 (RR+) Always Below 1 Ω
A41-22 (RR+) - Body ground Always 10 kΩ or higher
A41-9 (RR-) - WM1-2 (RR-) Always Below 1 Ω
A41-9 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A41-20 (RL+) - XM1-1 (RL+) Always Below 1 Ω
A41-20 (RL+) - Body ground Always 10 kΩ or higher
A41-7 (RL-) - XM1-2 (RL-) Always Below 1 Ω
A41-7 (RL-) - Body ground Always 10 kΩ or higher




OK

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
U183594E01
0.35,0.283 0.592,0.458 0.241,0.175 10 *a 1.178,2.677 1.531,2.828 0.353,0.151 10 RR+ 2.751,2.654 3.039,2.805 0.288,0.151 10 RL+ 0.317,1.101 0.659,1.252 0.342,0.151 10 WM1 1.773,1.101 2.078,1.252 0.304,0.151 10 XM1 2.694,2.172 2.889,2.639 false

Reconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
WM1-1 (RR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH:
Tester Connection Condition Specified Condition
XM1-1 (RL+) - Body ground Power switch on (IG) 5.7 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Sensor Wire)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

9.RECONFIRM DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.RECONFIRM DTC
a.

Turn the power switch off (lock).


b.

Reconnect the rear speed sensor connector and the skid control sensor wire.



d.

Turn the power switch on (ready).


e.

Perform a road test.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1466/33 and/or C1467/34 are output. A
DTCs C1466/33 and C1467/34 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY
a.

Turn the power switch off (lock).


b.

Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).

HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE).




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

b.

Turn the power switch on (ready).


c.

Perform a road test.


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1466/33 and/or C1467/34 are output (for LHD). A
DTCs C1466/33 and/or C1467/34 are output (for RHD). B
DTCs C1466/33 and C1467/34 are not output. C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

END