Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.12–2015.11
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C319941E07
5.031,3.958 7.146,4.375 2.115,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.031,3.771 5.344,3.927 0.313,0.156 10 false A41 0.25,4.042 2.448,4.271 2.198,0.229 10 false Combination Meter Assembly 0.25,3.875 0.563,4.031 0.313,0.156 10 false G1 5.969,0.906 6.417,1.063 0.448,0.156 10 false CA1L 5.969,1.76 6.417,1.917 0.448,0.156 10 false CA1H 5.698,0.813 5.917,0.969 0.219,0.156 10 false 38 5.698,1.625 5.917,1.781 0.219,0.156 10 false 37 0.885,0.927 1.333,1.083 0.448,0.156 10 false CANL 0.885,1.76 1.333,1.917 0.448,0.156 10 false CANH 1.385,0.823 1.604,0.979 0.219,0.156 10 false 32 1.385,1.615 1.604,1.771 0.219,0.156 10 false 31 5.969,2.875 6.417,3.031 0.448,0.156 10 false CSW 5.76,2.771 5.979,2.927 0.219,0.156 10 false 8 3.854,3.396 5.198,3.615 1.344,0.219 10 false VSC OFF Switch 3.854,3.24 4.427,3.396 0.573,0.156 10 false G76 4.833,2.76 5.052,2.917 0.219,0.156 10 false 6 3.781,2.76 4,2.917 0.219,0.156 10 false 3 4.667,3 4.885,3.156 0.219,0.156 10 false + 3.99,2.99 4.208,3.146 0.219,0.156 10 false E

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) , perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
Unknown: Unspecified
VSC OFF: VSC off mode
-


d.

Check the indicator light and mode condition on the intelligent tester changes according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (TRC OFF message) VSC OFF Indicator Light
Not pressed Normal Not displayed Does not come on
Pressing the VSC OFF switch TRC OFF Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF Displayed Comes on


Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display is normal C




A

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MULTI-INFORMATION DISPLAY (TRC OFF MESSAGE) AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MULTI-INFORMATION DISPLAY (TRC OFF MESSAGE) AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light Multi-information display (TRC OFF message) Display ON/OFF Observe combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly


b.

Check the multi-information display (TRC OFF message) and VSC OFF indicator light in the combination meter assembly turns on or off in accordance with intelligent tester operation.

OK:

The multi-information display (TRC OFF message) and VSC OFF indicator light turns on or off in accordance with intelligent tester operation.




OK

5.INSPECT VSC OFF SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VSC OFF SWITCH
a.
C239020E08
1.896,2.063 2.479,2.906 false 1.531,2.063 0.948,2.906 false 0.323,0.313 0.521,0.479 0.198,0.167 10 false *a 2.427,2.917 2.552,3.083 0.125,0.167 10 false E 0.854,2.917 0.979,3.083 0.125,0.167 10 false +

Turn the power switch off.


b.

Disconnect the VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (+) - 3 (E) Switch is pushed Below 1 Ω
6 (+) - 3 (E) Switch is not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(VSC OFF Switch)



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.

Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-8 (CSW) - G76-6 (+) Always Below 1 Ω
A41-8 (CSW) - Body ground Always 10 kΩ or higher
G76-3 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the power switch off.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The multi-information display and VSC OFF indicator light turns on or off in accordance with intelligent tester operation.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C