Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.12–2014.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1211/25  SLA Linear Solenoid  C1212/26  SLR Linear Solenoid  C1225/31  SA1 Solenoid Circuit  C1226/32  SA2 Solenoid Circuit  C1227/33  SA3 Solenoid Circuit  C1228/34  STR Solenoid Circuit  C1352/21  FR Solenoid  C1353/23  RR Solenoid  C1356/22  FL Solenoid  C1357/24  RL Solenoid  


DESCRIPTION

Each solenoid adjusts pressure which affects each wheel cylinder according to signals from the skid control ECU and controls the vehicle.

The master cut solenoid is closed and blocks the regulator pressure from the electronically controlled brake system control pressure when the system is normal. The master cut solenoid is open and sends the master cylinder and regulator hydraulic pressure to the non-assisted brake wheel cylinders during fail-safe operation during a system malfunction.

HINT:

If the supply voltage decreases, a drop in current may cause a DTC to be stored.


DTC No. INF Code DTC Detection Condition Trouble Area
C1211/25 21 Excess current is applied for 0.05 seconds or more. Brake booster with master cylinder assembly
↑ 22 An open is detected for 0.05 seconds or more while the solenoid is OFF. ↑
↑ 23 An open is detected for 0.05 seconds or more while the solenoid is ON.
·

Supply voltage reduced

·

Brake booster with master cylinder assembly


↑ 24 A short to +B or voltage leak is detected for 0.05 seconds. Brake booster with master cylinder assembly
C1212/26 31 Excess current is applied for 0.05 seconds or more. Brake booster with master cylinder assembly
↑ 32 An open is detected for 0.05 seconds or more while the solenoid is OFF. ↑
↑ 33 An open is detected for 0.05 seconds or more while the solenoid is ON.
·

Supply voltage reduced

·

Brake booster with master cylinder assembly


↑ 34 A short to +B or voltage leak is detected for 0.05 seconds. Brake booster with master cylinder assembly
C1225/31 41 Excess current is applied for 0.05 seconds or more. Brake booster with master cylinder assembly
↑ 42 An open is detected for 0.05 seconds or more while the solenoid is OFF. ↑
↑ 43 An open is detected for 0.05 seconds or more while the solenoid is ON.
·

Supply voltage reduced

·

Brake booster with master cylinder assembly


↑ 44 A short to +B or voltage leak is detected for 0.05 seconds. Brake booster with master cylinder assembly
C1226/32 51 Excess current is applied for 0.05 seconds or more. Brake booster with master cylinder assembly
↑ 52 An open is detected for 0.05 seconds or more while the solenoid is OFF. ↑
↑ 53 An open is detected for 0.05 seconds or more while the solenoid is ON.
·

Supply voltage reduced

·

Brake booster with master cylinder assembly


↑ 54 A short to +B or voltage leak is detected for 0.05 seconds. Brake booster with master cylinder assembly
C1227/33 61 Excess current is applied for 0.05 seconds or more. Brake booster with master cylinder assembly
↑ 62 An open is detected for 0.05 seconds or more while the solenoid is OFF. ↑
↑ 63 An open is detected for 0.05 seconds or more while the solenoid is ON.
·

Supply voltage reduced

·

Brake booster with master cylinder assembly


↑ 64 A short to +B or voltage leak is detected for 0.05 seconds. Brake booster with master cylinder assembly
C1228/34 71 Excess current is applied for 0.05 seconds or more. Brake booster with master cylinder assembly
↑ 72 An open is detected for 0.05 seconds or more while the solenoid is OFF. ↑
↑ 73 An open is detected for 0.05 seconds or more while the solenoid is ON.
·

Supply voltage reduced

·

Brake booster with master cylinder assembly


↑ 74 A short to +B or voltage leak is detected for 0.05 seconds. Brake booster with master cylinder assembly
C1352/21 11
12
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. Brake booster with master cylinder assembly
C1353/23 15
16
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. Brake booster with master cylinder assembly
C1356/22 13
14
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. Brake booster with master cylinder assembly
C1357/24 17
18
When the solenoid relay contact on, open or short in solenoid circuit continues for 0.05 seconds or more. Brake booster with master cylinder assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK DTC

b.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

HINT:

If a DTC for undervoltage is output, first troubleshoot the power source system.


Result:
Result Proceed to
DTCs C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and C1357/24 are not output. A
A DTC C1241/41 for undervoltage is output. B
DTCs C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and/or C1357/24 are output (for LHD). C
DTCs C1211/25, C1212/26, C1225/31, C1226/32, C1227/33, C1228/34, C1352/21, C1353/23, C1356/22 and/or C1357/24 are output (for RHD). D




A

B

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

D

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY