Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR(for RHD)
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278021 BRAKE PEDAL STROKE SENSOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



a.

When installing a new brake pedal stroke sensor assembly:

NOTICE:

Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the bolt.


i.
C249815E02
1.625,1.177 1.5,1.833 true 1.615,1.083 0.5,0.417 true 1.406,1.865 1.844,2.094 0.438,0.229 10 false *1 0.323,0.292 0.677,0.521 0.354,0.229 10 false *a

Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 bolts.

Text in Illustration
*1 Brake Pedal Stroke Sensor Assembly Lever
*a Brake Pedal Groove

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.




ii.

Connect the connector.


iii.

Firmly depress the brake pedal and break the brake pedal stroke sensor assembly lever set pin.


iv.

Remove the broken lever set pin.



b.

When reusing the brake pedal stroke sensor assembly:

i.
C249815E02
1.625,1.177 1.5,1.833 true 1.615,1.083 0.5,0.417 true 1.406,1.865 1.844,2.094 0.438,0.229 10 false *1 0.323,0.292 0.677,0.521 0.354,0.229 10 false *a

Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 bolts.

Text in Illustration
*1 Brake Pedal Stroke Sensor Assembly Lever
*a Brake Pedal Groove

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.



HINT:

Fully tighten the 2 bolts when adjusting the brake pedal stroke sensor assembly.



ii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89510D 4.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:

When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor".


e.
C249817

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard voltage (without the brake pedal depressed):

0.8 to 1.2 V



f.
C249818

Tighten the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



g.

Turn the intelligent tester off and turn the power switch off.


h.

Disconnect the intelligent tester.


Hide 6.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE