Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE SYSTEM
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278031 BRAKE SYSTEM G

BRAKE SYSTEM (OTHER)  BRAKE SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

A DTC may be stored during the inspection procedure. Be sure to clear the DTCs and check that no DTCs are output after the inspection is finished.


PROCEDURE

Hide 1.INSPECT PRESSURE SENSOR

a.

Check auxiliary battery voltage.

Standard voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge and SST, and connect the intelligent tester.

i.
C250042E01
0.84,0.371 0.639,0.371 false 2.052,0.371 1.934,0.371 false 2.781,0.371 2.634,0.371 false 0.84,0.287 1.001,0.434 0.161,0.147 10 *2 0.465,2.685 0.624,2.832 0.159,0.147 10 *3 2.87,2.523 3.034,2.670 0.164,0.147 10 *3 2.465,0.287 2.618,0.434 0.153,0.147 10 *2 2.052,0.287 2.203,0.434 0.151,0.147 10 *1 0.388,2.942 0.388,2.771 0.388,2.771 0.465,2.771 false 3.213,2.603 3.055,2.603 false

Set a pedal effort gauge and SST (LSPV gauge and No. 1 nipple).

SST
09709-29018  (09709-00060)

Text in Illustration
*1 Pedal Effort Gauge
*2 SST (LSPV Gauge)
*3 SST (No. 1 Nipple)


ii.

Connect the intelligent tester to the DLC3 with the power switch off, shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the intelligent tester on.


iv.

Bleed air from SST (LSPV gauge) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING).



c.

Inspect wheel cylinder pressure sensor and regulator pressure sensor.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test / Power Supply Air Bleeding Pattern 1.


ii.

Select "Wheel Cylinder Pressure Sensor" and "Regulator Pressure Sensor Output".


iii.

Check the value output from "Wheel Cylinder Pressure Sensor" and "Regulator Pressure Sensor Output" by depressing the brake pedal.

Standard Result:
Pedal Effort
N (kgf, lbf)
Regulator Pressure Sensor Output
(V)
Rear Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
Rear Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
50 (5, 11.2) 0.59 to 1.39 0.38 to 4.38 (3.9 to 44.6, 56 to 635) 0.38 to 4.38 (3.9 to 44.6, 56 to 635)
100 (10, 22.5) 1.55 to 2.35 5.08 to 9.08 (51.9 to 92.5, 737 to 1317) 5.08 to 9.08 (51.9 to 92.5, 737 to 1317)
150 (15, 33.7) 2.51 to 3.31 9.79 to 13.79 (99.9 to 140.6, 1421 to 2000) 9.79 to 13.79 (99.9 to 140.6, 1421 to 2000)
200 (20, 45.0) 3.47 to 4.27 14.49 to 18.49 (147.8 to 188.5, 2102 to 2681) 14.49 to 18.49 (147.8 to 188.5, 2102 to 2681)


Standard Result:
Pedal Effort
N (kgf, lbf)
Wheel Cylinder Pressure Sensor
(V)
Front Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
Front Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
50 (5, 11.2) 0.52 to 1.32 0.04 to 4.04 (0.5 to 41.1, 6 to 586) 0.04 to 4.04 (0.5 to 41.1, 6 to 586)
100 (10, 22.5) 1.34 to 2.14 4.06 to 8.06 (41.4 to 82.1, 589 to 1169) 4.06 to 8.06 (41.4 to 82.1, 589 to 1169)
150 (15, 33.7) 2.16 to 2.96 8.09 to 12.09 (82.5 to 123.2, 1174 to 1753) 8.09 to 12.09 (82.5 to 123.2, 1174 to 1753)
200 (20, 45.0) 2.98 to 3.78 12.09 to 16.09 (123.3 to 164.0, 1754 to 2333) 12.09 to 16.09 (123.3 to 164.0, 1754 to 2333)



iv.

After inspection, turn "Power Supply Air Bleeding Pattern 1" off.



d.

Remove pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed brake line (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING).



e.

Inspect accumulator sensor.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Accumulator Sensor".


ii.

Depress the brake pedal 4 or 5 times and operate the booster pump motor.


iii.

After confirming that the booster pump motor stops, check the output voltage.

Standard voltage:

2.9 to 4.2 V




Hide 47210L 2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.

Check auxiliary battery voltage.

Standard voltage:

11 to 14 V (while the power switch is off)



b.

Connect the intelligent tester and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the intelligent tester to the DLC3 with the power switch off, shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the intelligent tester on.




c.

Check operation without the brake booster.

i.

Inspect and adjust the brake pedal height.



ii.

Adjust the brake fluid level in the reservoir between the MIN line and the fluid level support line.

C256186E04
1.99,0.875 2.073,0.958 2.073,0.958 2.427,0.958 true 1.917,1.052 1.917,1.365 true 5.563,0.854 5.604,0.896 5.604,0.896 5.969,0.896 true 5.542,1.021 5.542,1.333 true 2.438,0.875 2.635,1.073 0.198,0.198 10 true *a 1.854,1.365 2.01,1.51 0.156,0.146 10 false *b 0.479,0.052 0.688,0.219 0.208,0.167 10 false *A 3.917,0.031 4.208,0.271 0.292,0.24 10 true *B 5.469,1.354 5.667,1.531 0.198,0.177 10 true *b 5.99,0.802 6.188,1 0.198,0.198 10 true *a

Text in Illustration
*A for LHD *B for RHD
*a Fluid Level Support Line *b MIN Line


iii.

Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility / Zero Down.

NOTICE:

Go to the next step without turning the power switch off.



iv.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Wheel Cylinder Pressure Sensor", "Stroke Sensor" and "Stroke Sensor 2".


v.

Check the value output from "Wheel Cylinder Pressure Sensor", "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort
N (kgf, lbf)
Wheel Cylinder Pressure Sensor
(V)
Stroke Sensor
(V)
Stroke Sensor 2
(V)
200 (20, 45.0) 0.51 to 1.31 1.13 to 1.83 3.17 to 3.87
500 (51, 112.4) 1.12 to 1.92 1.42 to 2.12 2.88 to 3.58



vi.

Turn the power switch off to finish "Zero Down".


vii.

Turn the power switch on (IG) and wait for 20 seconds, then enter the following menus: Chassis / ABS/VSC/TRC / Data List "Accumulator Sensor", and check the output voltage.

Standard voltage:

2.9 to 4.2 V




Hide 3.INSPECT STROKE SIMULATOR

a.

Check auxiliary battery voltage.

Standard voltage:

11 to 14 V (while the power switch is off)



b.

Connect the intelligent tester and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the intelligent tester to the DLC3 with the power switch off, the shift lever in P and the parking brake applied.


iii.

Turn the power switch on (IG) and turn the intelligent tester on.




c.

Check operation with the brake booster.

i.

Turn the power switch on (IG).


ii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor" and "Stroke Sensor 2".


iii.

Depress the brake pedal 4 or 5 times.


iv.

Check the value output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort
N (kgf, lbf)
Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 (5, 11.2) 1.29 to 1.99 3.01 to 3.71
100 (10, 22.5) 1.55 to 2.25 2.75 to 3.45
150 (15, 34.0) 1.71 to 2.41 2.59 to 3.29